• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2004년도 춘계학술대회논문집
• /
• pp.315-319
• /
• 2004

Static and dynamic responses of micro cantilever beam structures undertaking electrostatic forces are obtained employing Galerkin's method based on Euler beam theory. Variations of static and dynamic responses as well as resonant frequencies are estimated for several sets of beam properties and applied voltages. It is shown that the applied voltage influences the deflection and the modal characteristics significantly. Such information can be usefully employed for the design of MEMS structures.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2004년도 춘계 학술발표대회 개요집
• /
• pp.290-292
• /
• 2004

In this paper, static and fatigue load tests for the specimens, components and carbody were carried out to investigate the strength of welded joints in aluminum rolling stock. Tensile load test results showed that the static strength of welded joint for heat-treated alloys is reduced significantly and fatigue strengths are scattered by the welding imperfections. Component and whole carbody fatigue test results showed agreements with the design fatigue strength standards for specimens of same joint detail. Test results revealed that full penetration welding and strict management of welding procedure are crucial for securing strength of welded joint in aluminum carbody.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2006년도 제37회 하계학술대회 논문집 B
• /
• pp.960-961
• /
• 2006

In this paper, a static var compensator using three phase PWM Watkins-Johnson AC-AC converter is presented. The PWM Watkins-Johnson AC-AC converter is modelled by using circuit DQ transformation whereby the basic DC characteristics equation is analytically obtained. Finally, the PSIM simulation shows the validity of the modelling and analysis.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1995년도 하계학술대회 논문집 A
• /
• pp.46-49
• /
• 1995

This paper deals with characteristics of magnet that the levitation and guidance forces at static state and we tested and evaluated its. Also we compared to effect of levitation force with material and shape of guide way, focus on evaluation and method of test for the magnet of Urban Transit Maglev vehicle.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2001년도 제33회 춘계학술대회 개최
• /
• pp.224-230
• /
• 2001

A numerical analysis for the gas lubricated flexure-pivot tilting pad journal bearing has been accomplished. The film pressure are obtained by Newton-Raphson method and the dynamic coefficients are evaluated by the pad assembly method. The effects of the pivot position of the pad on the static and dynamic characteristics are presented for three pads journal bearing with LBP. The optimum pivot positions for the static performance is different from that of the dynamic performance.

• 한국자기학회지
• /
• 제5권5호
• /
• pp.567-569
• /
• 1995

By using the ac field source which can change the applied field magnitude, frequency and dc offset field, the dynamic magnetoresistance characteristics of permalloy based multilayers which have different R-H(resistance-magnetic field) curves were monitored and compared with static magnetoresistance curves that were measured with electromagnet of VSM. Output of each sample according to the external field strength was identified and optimum bias position could be obtained.

• 대한인간공학회지
• /
• 제17권2호
• /
• pp.25-32
• /
• 1998

A combined PC and TV monitor has been developed in several companies. The characteristics of physical user interface in this monitor are likely to vary from existing monitors. Therefore, two experiments to investigate the physical interface characteristics of this monitor were conducted. The first experiment was to investigate the characteristics of color perception with monitor coating (coating vs. non-coating) and screen brightness (30fL vs. 35fL) in the PC mode. The second experiment was to investigate the characteristics of luminance contrast with monitor coating and image movement (static vs. dynamic) in the TV mode. Twenty-three subjects (male 12, female 11) were participated in this experiment. In the first experiment, average color temperatures were obtained in all experimental conditions. There was a significant difference between coating and non-coating screen at 0.1 level. In the second experiment, average luminance contrasts were obtained in all experimental conditions. There was a significant difference between coating and non-coating screen at 0.05 level. In addition, there was a significant difference between static picture and dynamic picture at 0.1 level.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2007년도 제38회 하계학술대회
• /
• pp.1793-1794
• /
• 2007

Since it has an advantage of possibility to control using experimentally given coefficient, PID Control is the most widely used method of control in the field of industry. However, since PID controller is not able to reflect the inherent characteristics of individual systems, it needs to be accompanied by additional techniques to supplement. Also, it has disadvantage that it is hard to find a satisfactory coeffi cient when the state of the system's dynamic characteristics and static characteristics are different each other. When the dynamic one shows up, it means the state of system shows a great amount of difference from that of desired such as the moment of beginning control or change of desired state. But, if the state of the system comes close to the desired state, the static characteristics shows up in the system. There are many solutions suggested to overcome problems according to the conversion of two examples of motion shown above. This paper is to confirm PID control's integration ingredient windup phenomenon, and experiment through technique of pre vention of windup actually using PLC(Programmable Logic Co ntroller), and to verify the change in characteristics of control.

• 대한기계학회논문집A
• /
• 제33권12호
• /
• pp.1401-1409
• /
• 2009

All the forces in the real world act dynamically on structures. Design and analysis should be performed based on the dynamic loads for the safety of structures. Dynamic (transient or vibrational) responses have many peaks in the time domain. Topology optimization, which gives an excellent conceptual design, mainly has been performed with static loads. In topology optimization, the number of design variables is quite large and considering the peaks is fairly costly. Topology optimization in the frequency domain has been performed to consider the dynamic effects; however, it is not sufficient to fully include the dynamic characteristics. In this research, linear dynamic response topology optimization is performed in the time domain. First, the necessity of topology optimization to directly consider the dynamic loads is verified by identifying the relationship between the natural frequency of a structure and the excitation frequency. When the natural frequency of a structure is low, the dynamic characteristics (inertia effect) should be considered. The equivalent static loads (ESLs) method is proposed for linear dynamic response topology optimization. ESLs are made to generate the same response field as that from dynamic loads at each time step of dynamic response analysis. The method was originally developed for size and shape optimizations. The original method is expanded to topology optimization under dynamic loads. At each time step of dynamic analysis, ESLs are calculated and ESLs are used as the external loads in static response topology optimization. The results of topology optimization are used to update the design variables (density of finite elements) and the updated design variables are used in dynamic analysis in a cyclic manner until the convergence criteria are satisfied. The updating rules and convergence criteria in the ESLs method are newly proposed for linear dynamic response topology optimization. The proposed updating rules are the artificial material method and the element elimination method. The artificial material method updates the material property for dynamic analysis at the next cycle using the results of topology optimization. The element elimination method is proposed to remove the element which has low density when static topology optimization is finished. These proposed methods are applied to some examples. The results are discussed in comparison with conventional linear static response topology optimization.

• 한국가정과학회지
• /
• 제7권3호
• /
• pp.15-33
• /
• 2004

A precise understanding of the human form in static pose serves as the basis of designing clothing. When the human body is in motion, however, even an article of clothing designed to fit the human form in static pose can pull and change, thus restricting the body. In order to increase the fit of the clothing, which may be termed the second skin, its form and measurements therefore must be determined in correlation not only with the formal characteristics of the human body, in static pose but also with its functional characteristics in motion, as caused by the movements of the human body. In this study, the motion factor was selected as the primary basis for designing slacks with good fit in both static and moving states. By indentifying the areas in which lower limb movement cause significant changes in body surface lines, we suggest several application methods for designing slacks. Using unmarried female university students aged 18 - 24 as subjects, a total of 32 body surface categories (15 body surface lines and 17 body surface segment lines) were measured in one static and 9 movement poses. In particular, expansion and contraction levels and rates were measured and used in the analysis. The analysis first involved the calculation of the average measurement per body part in body surface line in static pose as well as of the average expansion and contraction levels and rates in 9 lower limb movements. Two-way MANOVA and multiple comparison analysis (Tukey) were conducted on movements and individual somatotypes regarding measurement per body part and expansion and contraction rates. Body parts whose measurements of body surface lines differed significantly in body surface line in static pose versus in movement were then identified. The results of this study are as follows. First, changes in body surface lines caused by lower limb movements were significant in all body surface lines of the lower trunk, both horizontal and vertical, with the exception of abdomen girth, midway thigh girth, ankle girth, hip length, and posterior knee girth. Second, significantly expanded 10 body surface lines in moving pose were detected and illustrated in table 4. These body parts should be studied in designing or pattern designing, especially for close-fitting pants, in using stretch fabric, and in sensory evaluation of good fit during movement.