• The Journal of Korean Academy of Prosthodontics
• /
• v.41 no.6
• /
• pp.762-771
• /
• 2003

Statement of problem. In dentistry, the minimally prepared inlay resin-bonded fixed partial denture (FPD) made of new ceromer / fiber-reinforced composite (FRC) was recently introduced. However, the appropriate dimensions for the long-term success and subsequent failure strength are still unknown. Purpose. The aim of this study was to investigate the most fracture-resistible thickness combination of the ceromer / FRC using a universal testing machine and an AE analyzer. Material and Methods. A metal jig considering the dimensions of premolars and molars was milled and 56-epoxy resin dies, which had a similar elastic modulus to that of dentin, were duplicated. According to manufacturer's instructions, the FRC beams with various thicknesses (2 to 4 mm) were constructed and veneered with the 1 or 2 mm-thick ceromers. The fabricated FPDs were luted with resin cement on the resin dies and stored at room temperature for 72 hours. AE (acoustic emission) sensors were attached to both ends, the specimens were subjected to a compressive load until fracture at a crosshead speed of 0.5 mm/min. The AE and failure loads were recorded and analyzed statistically. Results. The results showed that the failure strength of the ceromer/FRC inlay FPDs was affected by the total thickness of the connectors rather than the ceromer to FRC ratio or the depth of the pulpal wall. Fracture was initiated from the interface and propagated into the ceromer layer regardless of the change in the ceromer / FRC ratio. Conclusion. Within the limitations of this study, the failure loads showed significant differences only in the case of different connector thicknesses, and no significant differences were found between the same connector thickness groups. The application of AE analysis method in a fiber-reinforced inlay FPD can be used to evaluate the fracture behavior and to analyze the precise fracture point.

• The Journal of Korean Academy of Prosthodontics
• /
• v.41 no.3
• /
• pp.379-386
• /
• 2003

Statement of problem. Resin cements are widely used in adhesive dentistry specially on all ceramic restorations. It is needed to find out adequate bonding strength between different porcelain surface treatments, commercially available porcelains, and different resin cement systems. Purpose. The purpose of this study was to evaluate shear bond strength of resin cements bonded to porcelains in three different modalities; 5 different porcelain surface treatments, 3 different resin cement systems and 3 different commercially available pressable porcelains. Material and Method. This study consisted of 3 parts. Part I examined the effect of five different surface treatments on the pressable porcelain. Fifty discs (5 mm in diameter and 3 mm in height) of Authentic porcelain were randomly divided into 5 groups (n = 10). The specimens were sanded with 320 grit SiC paper followed by 600 grit SiC paper. The specimens were treated as follow: Group 1-Sandblasting (aluminum oxide) only, Group 2 - sandblasting/ silane, Group 3 - sandblasting/ acid etching/ silane, Group 4 - acid etching only, Group 5 - acid etching/ silane. Part II examined the shear bond strength of 3 different resin cement systems (Duolink, Variolink II, Rely X ARC) on acid etching/ silane treated Authentic pressable porcelain. Part 3 examined the shear bond strength of Duolink resin cement on 3 different pressable porcelains (Authentic, Empress I, Finesse). All cemented specimens were stored in distilled water for 2 hours and tested with Ultradent shear bond strength test jig under Universal Instron machine until fracture. An analysis of variance(ANOVA) test was used to evaluate differences in shear bond strength. Result. The shear bond strength test resulted in the following: (1) Acid etched porcelains recorded greater shear bond strength values to the sandblasted porcelains. (2) Silane treated porcelains recorded greater shear bond strength values to non-silane treated porcelains. (3) There was no significant difference between sandblasting/ acid etching/ silane treated and acid etching/ silane treated porcelains. However those values were much higher than other three groups. (4) The shear bond strength with Variolink II was lower than the value of Duolink or Rely X ARC. (5) The shear bond strength of Finesse was lower than the value of Authentic or Empress I.

• The Journal of Advanced Prosthodontics
• /
• v.1 no.1
• /
• pp.10-18
• /
• 2009

STATEMENT OF PROBLEM. Despite an improved bone reactions of Mg-incorporated implants in the animals, little yet has been carried out by the experimental investigations in functional loading conditions. PURPOSE. This study investigated the clinical and histologic parameters of osseointegrated Mg-incorporated implants in early loading conditions. MATERIAL AND METHODS. A total of 36 solid screw implants(diameter 3.75 mm, length 10 mm) were placed in the mandibles of 6 beagle dogs. Test groups included 18 Mg-incorporated implants. Turned titanium implants served as control. Gold crowns were inserted 4 weeks after implant placement and the dogs were immediately put on a food diet. Implants were observed for 10 weeks after loading. Radiographic assessments and stability tests were performed at the time of fixture installation, $2^{nd}$ stage surgery, 4 weeks after loading, and 10 weeks after loading. Histological observations and morphometrical measurements were also performed. RESULTS. Of 36 implants, 33 displayed no discernible mobility, corresponding to successful clinical function. There was no statistically significant difference between test implants and controls in marginal bone levels(P=.46) and RFA values. The mean BIC % in the Mg-implants was $54.5{\pm}8.4%$. The mean BIC % in the turned implant was $45.3{\pm}12.2%$. These differences between the Mg-implant and control implant were statistically significant(P=.005). CONCLUSIONS. The anodized, Mg-incorporated implant demonstrated significantly more bone-to-implant contact(BIC) in early loading conditions. CLINICAL IMPLICATIONS. The results of this study in beagle dogs suggest the possibility of achieving predictable stability of early loaded free-standing dental implants with Mg-incorporated surface.

• The Journal of Advanced Prosthodontics
• /
• v.1 no.1
• /
• pp.37-40
• /
• 2009

STATEMENT OF PROBLEM. Implant drivers are getting popular in clinical dentistry. Unlike to implant systems with external hex connection, implant drivers directly engage the implant/abutment interface. The deformation of the implant/abutment interface can be introduced while placing an implant with its implant driver in clinical situations. PURPOSE. This study evaluated the change of rotational freedom between an implant and its abutment after application of different insertion torques. MATERIAL AND METHODS. Three kinds of internal connection implants were utilized for the current study($4.5{\times}12\;mm$ Xive, $4.3{\times}11.5\;mm$ Inplant Magicgrip, $4.3{\times}12\;mm$ Implantium MF). An EstheticBase, a 2-piece top, a Dual abutment was used for its corresponding implant system. The rotational freedom between an implant and its abutment were measured before and after applying 45, 100 Ncm insertion torque. Repeated measures ANOVA was used for statistical analysis. RESULTS. Under 45 Ncm insertion torque, the rotational freedom between an implant and its abutment was significantly increased in Xive(P = .003). However, no significant change was noted in Inplant Magicgrip and Implantium MF. Under 100 Ncm torque, both in Xive(P = .0005) and Implatium MF(P = .03) resulted in significantly increased rotational freedom between the implant and its abutment. DISCUSSION. The design of the implant/implant driver interface effectively prevented the deformation of implant/abutment interface. Little change was noted in the rotational freedom between an implant and its abutment, even though the insertion torque was far beyond clinical application. CONCLUSIONS. The implant/abutment joint of internally connecting implants were quite stable under insertion torque in clinical situation.

• The Journal of Korean Academy of Prosthodontics
• /
• v.44 no.1
• /
• pp.10-19
• /
• 2006

Statement of problem : The various kinds of properties of post and core may affect the stress distribution to the root of endodontically treated teeth Purpose: To evaluate the influence of various kinds of properties of post and core to the stress distribution to the root of endodontically treated teeth. Material and methods: Mandibular first premolar, prepared by general shape of post and core with gold crown, was used to two dimensional axisymmetric modeling for finite element analysis. Then property values of 8 different kinds of post and core was substituted for each. Finally, stress distribution shown areas around the root of post and core was analysed after applying 50N of vortical and oblique load. Results: 1. Stress value of oblique load was much higher than the maximum stress value of vertical load. 2. Under oblique load, very concentrated stress was located on post periapical area and variations in stress were very severe. Contrary to this, stress distribution was relatively uniform in vertical load. 3. Post materials with higher elastic modulus showed relatively more apically focused stress, and post materials with lower elastic modulus showed stress focused on cervical area on the axial wall of post. 4. Stress change according to the properties of core was shown only in the cervical area of post and below core as the higher elastic modulus, then increased in stress. 5. Post and core with medium value of elastic modulus showed relatively uniform stress distribution. Conclusions: Post materials with higher elastic modulus showed relatively more apically focused stress, and post materials with lower elastic modulus showed stress focused on cervical area on the axial wall of post. Stress change according to the properties of core was shown only in the cervical area of post and below core.

• 대한공업교육학회지
• /
• v.39 no.1
• /
• pp.66-84
• /
• 2014

The purpose of this study is to develop STEAM hand-on activity task for middle school manufacturing & automation unit. This study was conducted following three stages. First of all, I carried out documents research and requirements analysis. And the goals for STEAM hand-on activity were set at this stage. Second, topics for STEAM hand-on activity were selected, and the organized for designing hand-on activity related STEAM in the development step. Finally, pilot and field test were conducted in order to amend and/or complement in improvement step. The theme and/or title of the hand-on activities were 'Making the print using wood', 'Making the close up photography & telephoto lens for smart phone'. The STEAM hand-on activities were designed for ten hours for each subject respectively. Each hand-on activity consists of problem situation, objectives statement, materials and tools, an evaluating criteria, related knowledge, portfolio and so on.

• Nutrition Research and Practice
• /
• v.9 no.5
• /
• pp.517-522
• /
• 2015

BACKGROUND/OBJECTIVES: The objective of this study was to investigate food allergens and prevalence rates of food allergies, followed by comparison of consumer attitudes and preferences regarding food allergy labeling by diagnosis of food allergies. SUBJECTS/METHODS: A total of 543 individuals living in Seoul and Gyeonggi area participated in the survey from October 15 to 22 in 2013. RESULTS: The results show that the prevalence of doctor-diagnosed food allergies was 17.5%, whereas 6.4% of respondents self-reported food allergies. The most common allergens of doctor-diagnosed and self-reported food allergy respondents were peaches (30.3%) and eggs (33.3%), respectively, followed by peanuts, cow's milk, and crab. Regarding consumer attitudes toward food labeling, checking food allergens as an item was only significantly different between allergic and non-allergic respondents among all five items (P < 0.001). All respondents reported that all six items (bold font, font color, box frame, warning statement, front label, and addition of potential allergens) were necessary for an improved food allergen labeling system. PLSR analysis determined that the doctor-diagnosed group and checking of food allergens were positively correlated, whereas the non-allergy group was more concerned with checking product brands. CONCLUSIONS: An effective food labeling system is very important for health protection of allergic consumers. Additionally, government agencies must develop policies regarding prevalence of food allergies in Korea. Based on this information, the food industry and government agencies should provide clear and accurate food labeling practices for consumers.

• Journal of the Korea Convergence Society
• /
• v.10 no.10
• /
• pp.21-26
• /
• 2019

At present, it is indispensable to utilize data as an information society. Therefore, the database is used to manage large amounts of data. In real life, most of the data in a database is the personal information of a group of members. Because personal information is sensitive data, the role of the database administrator who manages personal information is important. However, there is a growing number of attacks on databases to use this personal information in a malicious way. SQL Injection is one of the most known and old hacking techniques. SQL Injection attacks are known as an easy technique, but countermeasures are easy, but a lot of efforts are made to avoid SQL attacks on web pages that require a lot of logins, but some sites are still vulnerable to SQL attacks. Therefore, this study suggests effective defense measures through analysis of SQL hacking technology cases and contributes to preventing web hacking and providing a secure information communication environment.

• Journal of the Korean Society of Earth Science Education
• /
• v.11 no.3
• /
• pp.237-243
• /
• 2018

The purpose of this study is to analyze the contents related to a subject 'Earth and Mooon' from elementary science textbooks of the 2009 revised curriculum and elementary science textbooks of the 2015 revised curriculum. For the research, the team selected and analyzed the contents of the 'Earth and Moon' unit in the elementary science textbooks of the 2009 revised curriculum and 2015 revised curriculum. As a result of the research, first, there has been no significant change in achievement standards of the curriculum as the science textbook revised from 2009 curriculum to 2015 curriculum. Second, the two curriculum did not differ much in specific textbook contents statement or development, but they showed much change in presentation of exploration activities in curriculum as well as the specific exploration activities presented in the textbooks. Third, compared to science textbooks of the 2009 revision the 2015 revision used more pictures and illustrations. Forth, there have been few changes related to experimental observation, but the activities to organize the unit in 2015 revision have been strengthened compared to the 2009 revision.

• 한국노년학
• /
• v.36 no.4
• /
• pp.959-979
• /
• 2016

This study was performed to explore the life experience as a teacher was dissolved in life aimed at elementary school female teachers. The selection of the four-year teaching career more than 35 years, from January to November 2015 and retired teacher retirement not more than three years to 2015, five people in the study participants were conducting research. Research method was approached narrative interview method of qualitative research, Sch?tze of biographical research methods utilized in exploring how narratives. Results from this study showed the biographical curve through the 'biographical statement', 'experience the life of a female teacher','difficulties experienced in the reality of female teachers', 'reward as a teacher', divided into the categories' 'post-retirement life adaptation types'. These findings are in accordance with the retirement teacher pointed out the lack of social adaptation programs, such as training or preparation for life after retirement, With the increasing need for pre-retirement training is to prepare for life after retirement were suggestions that the government offers programs and information about the life after retirement is necessary.