• Proceedings of the KIEE Conference
• /
• 2006.10b
• /
• pp.154-158
• /
• 2006

The switching-mode power converter has been widely used because of its features of high efficiency and small weight and size. These features are brought by the ON-OFF operation of semiconductor switching devices. However, this switching operation causes the surge and EMI(Electromagnetic Interference) which deteriorate the reliability of the converter themselves and entire electronic systems. This problem on the surge and noise is one of the most serious difficulties in AC-to-DC converter. Random Pulse Width Modulation (RPWM) is peformed by adding a random perturbation to switching instant while output-voltage regulation of converter is performed. RPWM method for reducing conducted EMI in single switch three phase discontinuous conduction mode boost converter is presented. The more white noise is injected, the more conducted EMI is reduced. But output-voltage is not sufficiently regulated. This is the reason why carrier frequency selection topology is proposed. In the case of carrier frequency selection, output-voltage of steady state and transient state is fully regulated. A RPWM control method was proposed in order to smooth the switching noise spectrum and reduce it's level. Experimental results are verified by converter operating at 300v/1kW with $5%{\sim}30%$ white noise input. Spectrum analysis is performed on the Phase current and the CM noise voltage. The former is measured with Current Probe and the latter is achieved with LISN, which are connected to the spectrum analyzer respectively.

• Journal of Power Electronics
• /
• v.16 no.2
• /
• pp.542-552
• /
• 2016

Central 60° synchronous modulation is an easy pulse-width modulation (PWM) method to implement for the traction inverters of urban rail trains at a very low switching frequency. Unfortunately, its switching patterns are determined by a Fourier analysis of assumed steady-state voltages. As a result, its transient responses are not very good with over-currents and high instantaneous torque pulses. In the proposed solution, the switching patterns of the conventional central 60° modulation are modified according to the dynamic error between the target and actual stator flux. Then, the specific trajectory of the stator flux and current vector can be guaranteed, which leads to better system transients. In addition, stator flux control is introduced to get smooth mode switching between the central 60° modulation and the other PWMs in this paper. A detailed flow chart of the control signal transmission is given. The target flux is obtained by an integral of the target voltage. The actual PMSM flux is estimated by a minimum order flux state observer based on the extended flux model. Based on a two-level inverter model, improved rules in the α-β stationary coordinate system and equations of the switching patterns amendment are proposed. The proposed method is verified by simulation and experimental results.

• Nuclear Engineering and Technology
• /
• v.49 no.1
• /
• pp.209-215
• /
• 2017

Fast neutron irradiation was used to improve the switching speed of a 600-V nonpunch-through insulated gate bipolar transistor. Fast neutron irradiation was carried out at 30-MeV energy in doses of $1{\times}10^8n/cm^2$, $1{\times}10^9n/cm^2$, $1{\times}10^{10}n/cm^2$, and $1{\times}10^{11}n/cm^2$. Electrical characteristics such as current-voltage, forward on-state voltage drop, and switching speed of the device were analyzed and compared with those prior to irradiation. The on-state voltage drop of the initial devices prior to irradiation was 2.08 V, which increased to 2.10 V, 2.20 V, 2.3 V, and 2.4 V, respectively, depending on the irradiation dose. This effect arises because of the lattice defects generated by the fast neutrons. In particular, the turnoff delay time was reduced to 92 nanoseconds, 45% of that prior to irradiation, which means there is a substantial improvement in the switching speed of the device.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.35 no.4
• /
• pp.348-352
• /
• 2022

Resistive switching behaviors of a co-sputtered zinc silicate thin film (ZnO and SiO₂ targets) have been investigated. We fabricated an Ag/ZnSiO_x/highly doped n-type Si substrate device by using an RF magnetron sputter system. X-ray diffraction pattern (XRD) indicated that the Zn₂SiO₄ was formed by a post annealing process. A unique morphology was observed by scanning electron microscope (SEM) and atomic force microscope (AFM). As a result of annealing process, 50 nm sized nano clusters were formed spontaneously in 200~300 nm sized grains. The device showed a unipolar resistive switching process. The average value of the ratio of the resistance change between the high resistance state (HRS) and the low resistance state (LRS) was about 106 when the readout voltage (0.5 V) was achieved. Resistance ratio is not degraded during 50 switching cycles. The conduction mechanisms were explained by using Ohmic conduction for the LRS and Schottky emission for the HRS.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.25 no.8
• /
• pp.899-905
• /
• 1988

In this paper, we suggest a new quasi-sliding mode condition with a wighting factor which guarantees all the states to reach switching planes and improves the convergence of the state trajectories. The result of computer simulation shows that by the suitable selection of a weighting factor, all the state trajectories reach switching planes and enter the sliding mode having the property of the insensitivity to parameter variation and disturbances.

• Journal of the Korean Operations Research and Management Science Society
• /
• v.4 no.1
• /
• pp.41-51
• /
• 1979

The Classical multi-server heterogeneous queuing system can be more generalized by using the concept of the switching rules. The descriptions of these systems, the relations among the state probebilities at the various points of interest, and comparisons with the single-server system will be presented. Instead of using the imbedded markov chain we set up the simultaneous equations for the state probabilites by the supplementary variable method.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2005.07a
• /
• pp.105-108
• /
• 2005

We demonstrate an electro-optical device based on the flexoelectric effect of a short-pitched cholesteric liquid crystal. By using a dual-frequency switchable nematic, a small amount of chiral dopant and a small amount of phase-separated polymer localized on the surface, we were able to create a device that operates in amplitude (flexoelectric) and phase(dielectric) modes. At high frequency the dual frequency liquid crystal suppresses the phase mode at higher voltage, which improves the switching speed, and thereby preserving the in-plane-switching mode.

• Journal of information and communication convergence engineering
• /
• v.8 no.4
• /
• pp.421-426
• /
• 2010

This paper presents a method of design the counter using sequential system based on synchronous techniques. For the design the counter, first of all, we derive switching algebras and their operations. Also, we obtain the next-state functions, flip-flop excitations and their input functions from the flip-flop. Then, we propose the algorithm which is a method of implementation of the synchronous sequential digital logic circuits. Finally, we apply proposed the sequential logic based on synchronous techniques to counter.

• Proceedings of the Korean Magnestics Society Conference
• /
• 2002.12a
• /
• pp.186-187
• /
• 2002

Recently, there has been much interest in magnetic thin film patterned in submicron scale because of possible ultrahigh density storage media or logical device applications [1-3]. Various geometries such as rectangle, circle, ring and ellipse type dots have been studied to find the shape showing stable switching behavior from repeated cycles. However, rectangle and circle types may not be suitable for device applications because they have two uncontrollable different magnetization reversal modes: C state and S state, resulting in different coercivity and irreproducible switching[4]. (omitted)

• Proceedings of the KIPE Conference
• /
• 1998.07a
• /
• pp.85-89
• /
• 1998

A switching power stage is a very nonlinear system because it has two or more operation modes in one switching cycle. To model a switching power stage, the state space averaging method has been developed. Though it allows a unified treatment of a large variety of switching power stages, the model it yields is always very nonlinear. So, it is required to linearize the averaged model. But it is well known that a controller for a nonlinear plant designed by the linearization frequently fails in showing satisfactory control performance. Hence it is very natural to try to design a nonlinear controller for a switching power stage. In design of a switching power system, nonlinear control approaches such as adaptive control and fuzzy control have been widely studied so far. In this research, a recently developed control method, time delay control is briefly studied and a design example for a ZVS PWM half bridge converter is given. The performance of the time delay controller is compared to its conventional counterpart, PI controller by computer simulations.