한국기준 표준화된 A급 목재 및 B급 유류 화재 시험에서 룸코너시험기(RCT)를 사용하여 연소유독가스의 생성을 정량적으로 알아보고, 시험자들에게 미치는 인체유해성을 확인하였다. 그 결과 A급의 경우 유독가스가 시험자들에 직접적으로 노출되는 초기 3분 동안, 분당호흡량(RMV) 2단계에서 40% 카복시헤모글로빈(COHb)가 넘어가는 경우는 A급 9, 10단위에 해당하며, RMV 3단계에서 A급 5~10 단위까지가 모두 40% COHb을 초과함을 확인하였다. 한편 B급의 경우 유독가스가 시험자에게 직접 노출되는 초기 1분 동안은 A급에 비해 다소 안전하나 총 연소시간에는 RMV 3단계에서 B급 16~20 단위까지가 모두 20% COHb을 초과한 수치가 나옴을 확인하였다. 따라서 이 연구에서는 시험자들은 소화시험의 단위수를 고려하여 자급 호흡보조기나 그와 동일한 기능의 장치를 착용하는 규정을 제안한다.
무기재로서 질석은 친환경적인 특성과 내화, 단열, 흡음 뿐 만 아니라 결로방지, 탈취 및 미관 등이 우수하므로 건축마감재로서 활용될 경우 효용성이 높을 것으로 판단된다. 본 연구에서는 질석을 주원료로 하여 미네랄 루즈울(Mineral Loose Wool) 또는 미네랄 파우더(Mineral Powder)를 혼입한 건축용 마감보드를 개발하고 불연시험과 단열시험을 수행하였다. 시험결과 두 개의 질석보드 모두 불연재로서 성능을 확보하였으며 열전도율 0.086 및 $0.092W/m{\cdot}K$로 나타났다. 또한 개발된 두 개의 질석보드를 경골목구조 내화벽체 표준상세(KS F 1611-1)의 마감재로 적용하여 내화시험을 수행하였다. 내화시험결과 VB-L 시험체가 VB-P시험체 보다 내화성능이 다소 높게 나타났으며 두 개의 질석보드 모두 두께 30 mm로도 내화성능 2시간 확보가 충분한 것으로 나타났다.
연기독성생성물로 인한 인명피해가 주요한 화재피해로 보고되고 있다. 화재로 인한 연기독성을 평가하기 위해 국내외의 다양한 시험이 있으며, 국내에서는 KS F 2271의 가스유해성시험으로 건축마감재료의 유해성을 평가하고 있다. 현행 가스유해성시험은 발연가스를 설치류(실험용 흰 쥐)에 노출시켜 행동시간을 측정하여 연소가스 독성을 평가한다. 본 연구에서는 가연성 고분자소재(우레탄 및 고무바닥재)를 대상으로 가스유해성시험을 수행하고 이때 발생되는 가스를 FT-IR로 정량분석하였다. 정량분석결과는 BS6853에서 규정하는 기준값과 비교하여 독성지수(R)를 산정하였다. 동물시험과 독성지수의 상대적 비교를 통해 두 시험법의 상관성을 분석하여 다양한 독성평가를 시도하고자 하였다.
국내 건축물에 사용되는 내화도료는 품질시험을 통하여 내화구조로 인정받아야 사용할 수 있다. 품질시험은 내화시험 및 부가시험이며 내화도료의 부가시험 항목은 가스유해성과 부착강도이다. 이중 가스유해성의 경우 관련 KS 등에 따라 동물실험을 하며 매건 16마리의 살아있는 쥐가 희생된다. 이에 실험자는 윤리적 부담을 느끼게 되며 실험기관은 관련 법률에 따른 실험동물운영위원회 운영 등 행정적 부담을 지게 된다. 이에 연소 가스의 성분 분석을 통한 유해성 측정 등 상기 동물실험을 대체하려는 연구와 노력이 지속되고 있으나 현재까지는 동물실험이 유지되고 있다. 연소가스의 유해성 평가 시 시험체 가열에 따라 발생하는 배기온도가 측정되는데 특정 타입 내화도료에 대한 배기온도를 분석하여 유의한 초기 반응 양상을 파악할 수 있다면 동물실험 대체에 기여할 수 있을 것이라 사료된다. 이에 본 논문을 통하여 가스유해성 시험 시 쥐의 행동정지시간과 배기온도와의 관계를 파악하여 현 동물실험의 개선점을 찾아보고자 하였다.
The flammable liquid conductivity is an important factor in determining the generation of electrostatic in fire and explosion hazardous areas, so it is necessary to study the physical properties of flammable liquids. In particular, the relevant liquid conductivity in the process of handling flammable liquids in relation to the risk assessment and risk control in fire and explosion hazard areas, such as chemical plants, is classified as a main evaluation item according to the IEC standard, and it is necessary to have flammable liquid conductivity measuring devices and related data are required depending on the handling conditions of the material, such as temperature and mixing ratio for preventing the fire and explosion related to electrostatic. In addition, IEC 60079-32-2 [Explosive Atmospheres-Part 32-2 (Electrostatic hazards-Tests)] refers to the measuring device standard and the conductivity of a single substance. It was concluded that there is no measurement data according to the handling conditions such as mixing ratio of flammable liquid and temperature together with the use and measurement examples. We have developed the measurement reliability by improving the structure, material and measurement method of measuring device by referring to the IEC standard. We have developed a measurement device that is developed and manufactured by itself. The test results of flammable liquid conductivity measurement and the data of the NFPA 77 (Recommended Practice on Static Electricity) Annex B Table B.2 Static Electric Characteristic of Liquids were compared and verified by conducting the conductivity measurement of the flammable liquid handled in the fire and explosion hazardous place by using Measuring / Data Acquisition / Processing / PC Communication. It will contribute to the prevention of static electricity related disaster by taking preliminary measures for fire and explosion prevention by providing technical guidance for static electricity risk assessment and risk control through flammable liquid conductivity measurement experiment. In addition, based on the experimental results, it is possible to create a big data base by constructing electrostatic physical characteristic data of flammable liquids by process and material. Also, it is analyzed that it will contribute to the foundation composition for adding the specific information of conductivity of flammable liquid to the physical and chemical characteristics of MSDS.
열감지기는 화재시 발생되는 열을 감지하는 것으로 모든 소방대상물에 일반적으로 사용되는 자동화재탐지설비의 중요한 핵심 요소이다. 열감지기는 스포트(spot)형과 분포형으로 구분되며, 스포트형에는 차동식과 정온식이 있다. 이러한 열감지기는 실제 화재시 작동시간 및 작동온도 등 반응의 민감도에 따라 인명과 재산 손실에 큰 영향을 준다. 국내에서는 스프링클러 헤드제품에 응답시간지수를 도입하여 사용하고 있으나, 열감지기에 대해서는 현재 적용이 되어지지 않고 있으며, 반응의 민감도를 표시하는 응답시간지수의 도입이 필수적으로 본 연구에서는 국내 생산된 정온식 스포트형 열감지기와 다이아프램형 및 반도체 형식의 차동식 스포트형 열감지기에 대하여 풍동실험 및 화재실험을 통하여 응답시간지수, 작동시간, 작동온도 등에 대하여 연구하였다. 응답시간지수를 적용한 열감지기를 설치하여 신속한 경보로 인한 국민의 생명과 재산손실을 줄이는데 도움을 주고자 한다.
본 논문은 오염물질에 따른 HFIX 절연전선 피복의 특성변화에 관한 연구이다. HFIX 절연전선 피복을 오염시키기 위해 전선의 내수성시험 항목인 KS C IEC 60811-1-3 규격을 인용, 오염물질을 선정하고 선정된 오염물질에 시료를 노출시켜 주차 별 최대 4주간 노출된 실험시료를 제작하였다. 그 후 주차 별 시료들을 대상으로 최대인장하중 및 신장률을 측정하였다. 오염노출 기간이 길어짐에 따라 최대인장하중이 상온시료의 경우 6.22%, 고온시료 6.52%, 방청윤활제 19.94% 감소하였고, 신장률 또한 급격하게 감소하여 피복 특성저하가 뚜렷하게 나타났다. 추가적인 주사전자현미경을 이용한 표면 분석결과 오염기간이 길어짐에 따라 천공, 갈라짐, 용융 등의 구조 변경 현상이 발생되어 기계적 특성이 감소되는 것으로 나타났다. 따라서 절연전선의 성능저하를 방지하기 위해 검사주기 및 보수시기의 마련이 필요할 것으로 생각된다.
Estimates of wind-induced wind effects on tall buildings are based largely on 1980s technology. Such estimates can vary significantly depending upon the wind engineering laboratory producing them. We describe an efficient database-assisted design (DAD) procedure allowing the realistic estimation of wind-induced internal forces with any mean recurrence interval in any individual member. The procedure makes use of (a) time series of directional aerodynamic pressures recorded simultaneously at typically hundreds of ports on the building surface, (b) directional wind climatological data, (c) micrometeorological modeling of ratios between wind speeds in open exposure and mean wind speeds at the top of the building, (d) a physically and probabilistically realistic aerodynamic/climatological interfacing model, and (e) modern computational resources for calculating internal forces and demand-to-capacity ratios for each member being designed. The procedure is applicable to tall buildings not susceptible to aeroelastic effects, and with sufficiently large dimensions to allow placement of the requisite pressure measurement tubes. The paper then addresses the issue of accounting explicitly for uncertainties in the factors that determine wind effects. Unlike for routine structures, for which simplifications inherent in standard provisions are acceptable, for tall buildings these uncertainties need to be considered with care, since over-simplified reliability estimates could defeat the purpose of ad-hoc wind tunnel tests.
The purpose of this study is to examine the cause of damage to electrolytic capacitors and to present the heat generation mechanism in order to prevent the occurrence of similar problems. From the analysis results of electrolytic capacitors collected from accident sites, the fire causing area can be limited to the primary power supply for the initial accident. From the tests performed by applying overvoltage, surge, etc., it is thought that the fuse, varistor, etc., are not directly related to the accidents that occurred. The analysis of the characteristics using a switching regulator showed that the charge and discharge characteristics fell short of standard values. In addition, it is thought that heated electrolytic capacitors caused thermal stress to nearby resistances, elements, etc. It can be seen that the heat generation is governed by the over-ripple current, application of AC overvoltage, surge input, internal temperature increase, defective airtightness, etc. Therefore, when designing an electrolytic capacitor, it is necessary to comprehensively consider the correct polarity arrangement, appropriate voltage application, correct connection of equivalent series resistance(ESR) and equivalent series inductance(SEL), rapid charge and discharge control, sufficient margin of dielectric tangent, etc.
성능위주설계의 설계화원 정보는 피난안전성 평가에 직접적인 영향을 미치기 때문에, 실물화재 실험에 근거한 설계화원의 설정이 매우 중요하다. 복합영상관에 대한 성능위주설계의 신뢰성을 개선시키기 위하여, 상영관 의자에 대한 화재실험을 통해 열발생률과 화재확산속도 등의 화재거동에 관한 정보를 제공한다. 이를 위하여 실제 상영관과 유사하게 배열된 다수의 객석 의자가 적용되었다. 주요 결과로서, 객석의자 1개에 대하여 최대 열발생률과 단위 질량당 발열량은 각각 415~988 kW와 15.2~23.8 MJ/kg의 범위를 갖는다. 신형과 구형 객석의자의 평균 단위 질량당 발열량은 각각 23.6 MJ/kg과 16.7 MJ/kg으로 측정되었다. 즉, 신형의자의 증가된 플라스틱 및 쿠션재의 함량으로 인하여, 신형이 구형에 비해 화재위험성이 높은 것으로 확인되었다. 추가로 객석의자가 일렬로 배치될 때, 점화위치와 상관없이 0.39~0.42 m/min의 화재확산속도가 관찰되었다. 마지막으로 복합영상관의 성능위주설계를 위하여 객석의자의 최대 열발생률과 화재성장률로 구성된 화재성장곡선이 제안되었다.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.