• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2005년도 춘계학술발표대회 논문집
• /
• pp.141-145
• /
• 2005

Since the electromagnetic properties of fiber reinforced polymeric laminate composite can be tailored effectively by adjusting its composition and regulating the stacking sequence, it is plausible material for fabricating the radar absorbing structures (RAS) of desired performance. In order to design the effective electromagnetic wave (EM) absorber with the fiber reinforced polymeric laminate composite, its electromagnetic characteristics should be available and could be regulated easily in the target frequency bands. In this study, dielectric characteristics of the E-glass/epoxy laminate composites were measured by the free space method in the X-band frequency range ($8.2\;{\sim}\;12.4\;GHz$). In order to describe the dielectric behavior of laminate composites of arbitrary stacking sequences, the equivalent circuit model and the laminating equations for estimating dielectric properties were proposed, and experimentally verified. From the comparison of the predicted and measured data, the proposed method predicted well the experimentally measured data.

• 한국생산제조학회지
• /
• 제21권4호
• /
• pp.608-612
• /
• 2012

To reduce these costs and time by finite element analysis program has been much research (3~4). At virtual CAE program as like Abaques, Ansys, Ls-dyna and Nastran, the input data of material is got bellow coupon test. In case of carbon composite, it is also put in lamina/laminate properties. There have big problem. If you want to simulate FW(filament winding or wind blade) how do you input material data. Each area of FW is different stacking conditions. It's too hard that each area is tested for inputting lamina or laminate properties. The composite structure increasing load is applied occurred as the matrix dependence of the crack-induced nonlinearity and nonlinear mobility appears since the initial damage. And uni-direction for this research applies the theory to have been confined to. On this study, we are going to get basically fiber properties and matrix than carbon composite properties for simulating according stacking method by GENOA-MCQ. It is help to simulate easily composite material. Also Calculate the matrix nonlinear for simulating non-linear.

• Bulletin of the Korean Chemical Society
• /
• 제32권9호
• /
• pp.3255-3260
• /
• 2011

Two novel binuclear metal-organic coordination complexes $[Cd_2(L)_2(bpy)_2(H_2O)_2]{\cdot}6H_2O$ (1), $[Cd_2(L)_2(phen)_2-(H_2O)_2]{\cdot}2H_2O$ (2) (where L = 2-methylquinoline-3,4-dicarboxylate dianion, bpy = 2,2'-bipyridine, phen = 1,10-phenanthroline) have been synthesized under hydrothermal conditions and characterized by single crystal Xray diffraction, spectral method (IR), elemental analysis and thermal gravimetric analysis (TGA). Both 1 and 2 consist of two Cd(II) atoms bridged by two monoatomic bridging carboxylate groups from two L ligands, and the second carboxylate group of each L is monodentately coordinated to Cd(II), creating a sevenmembered chelating ring. The coordination at each metal nucleus is completed by a water molecule and a chelating bidentate molecule. The 3D structures of the complexes are stabilized by ${\pi}-{\pi}$ stacking interactions and hydrogen-bonds.

• 한국공작기계학회논문집
• /
• 제17권3호
• /
• pp.34-39
• /
• 2008

In this study, CFRP(Carbon Fiber Reinforced Plastics) that has high specific strength and elastic modulus and low thermal strain was used as a material for the lightweight structural member. CFRP is a fiber material as anisotropic material. The anisotropic material is characterized by the change of its mechanical properties according to stacking orientation angle. CFRP orientation angle was oriented in [A/B]s in order to examine the effect of CFRP orientation angle on the characteristics of energy absorption. CFRP is very weak to the impact from the outside. So, when impact is applied to CFRP, its strength is rapidly lowered. The hybrid material was manufactured by combining CFRP to aluminum which is lightweight and widely used for structural members of the automobile. The hybrid member was shaped as a side member that could support the automobile engine and mount and absorb a large amount of impact energy at the front-end in case of automobile collision. The bending test device was manufactured in accordance with ASTM standard, and mounted to UTM for bending test. For comparing bending characteristics of the hybrid member with those of Aluminum and CFRP member, tests were performed for aluminum, CFRP and hybrid member, respectively.

• Steel and Composite Structures
• /
• 제19권6호
• /
• pp.1501-1510
• /
• 2015

The frequency selective surface (FSS) embedded hybrid composite materials have been developed to provide excellent mechanical and specific electromagnetic properties. Radar absorbing structures (RASs) are an example material that provides both radar absorbing properties and structural characteristics. The absorbing efficiency of an RAS can be improved using selected materials having special absorptive properties and structural characteristics and can be in the form of multi-layers or have a certain stacking sequence. However, residual stresses occur in FSS embedded composite structures after co-curing due to a mismatch between the coefficients of thermal expansion of the FSS and the composite material. In this study, to develop an RAS, the thermal residual stresses of FSS embedded composite structures were analyzed using finite element analysis, considering the effect of stacking sequence of composite laminates with square loop (SL) and double square loop (DSL) FSS patterns. The FSS radar absorbing efficiency was measured in the K-band frequency range of 21.6 GHz. Residual stress leads to a change in the deformation of the FSS pattern. Using these results, the effect of transmission characteristics with respect to the deformation on FSS pattern was analyzed using an FSS Simulator.

• 한국해양공학회지
• /
• 제27권2호
• /
• pp.8-12
• /
• 2013

Four kinds of silicon nitride composites with tri-laminate structure were prepared by stacking tapes with aligned ${\beta}-Si_3N_4$ whisker seeds. The composites were fabricated using a modified tape casting method for enhanced alignment of the whisker seeds. The relative densities of all four samples reached 99% at room temperature. The three-point flexural strengths of the samples according to the stacking sequences were measured at both room temperature and 1723 K. The high temperature strength of sample WWW was $457{\pm}14$ MPa. The fracture of sample WWW occurred mainly along the grain boundary. The room temperature strengths of samples OOO, OWO, WOW, and WWW were $430{\pm}32$ MPa, $470{\pm}19$ MPa, $700{\pm}14$MPa, and $940{\pm}14$ MPa, respectively.

• Bulletin of the Korean Chemical Society
• /
• 제34권2호
• /
• pp.374-378
• /
• 2013

Two novel binuclear metal-organic coordination complexes [$Cd_2(Hdpa)_4(bpy)_2$] (1), [$Dy_2(dpa)_2(bpy)_2(NO_3)_2-(H_2O)_2$](bpy) (2) (where $H_2dpa$ = biphenyl-2,2'-dicarboxylic acid, bpy = 2,2'-bipyridine) have been synthesized under hydrothermal conditions and characterized by single crystal X-ray diffraction, spectral method (IR), elemental analysis (EA), powder X-ray diffraction (XRD), electronic spectra (UV-vis), fluorescent in the solid state and thermogravimetric analysis (TGA). Complexes 1-2 crystallizes isomorphously in the Triclinic space group P-1. The ${\pi}-{\pi}$ stacking interactions and hydrogen-bonds play a vital role in determining the crystal packing and construction of the extended 3-D supramolecular network.

• 한국안전학회지
• /
• 제27권6호
• /
• pp.20-25
• /
• 2012

Currently, the most important purpose in designing automobile is environment-friendly and safety performance aspect. CFRP(Carbon Fiber Reinforced Plastics) of the advanced composite materials as structure materials for vehicles, has a wide application in lightweight structural materials of air planes, ships and automobiles because of high strength and stiffness. In this study, experimental investigations are carried out for CFRP single and double hat shaped section member in order to study the effect of various stacking condition. They were cured by heating to the appropriate curing temperature($130^{\circ}C$) by means of a heater at the vacuum bag of the autoclave. The stacking conditions were selected to investigate the effect of the interface numbers. The CFRP single and double hat shaped section members which manufactured from unidirectional prepreg sheets were made of 8ply. The static collapse tests performed and the collapse mode and energy absorption capability were analyzed according to interface number.

• 한국염색가공학회지
• /
• 제31권2호
• /
• pp.65-76
• /
• 2019

A multi-point touch input sensor having different sizes or different capacitance touch points connected by only one pair of signal transmission lines was fabricated using a polyimide film coated with a thin copper plate. The capacitance increases with the decrease in the number of sheets of fabric spacers placed between the two sheets of the polyimide film. Therefore, the touch input sensor could be manufactured without fabric spacers, which was possible by the action of the polyimide film as a dielectric material in the capacitor. On the multi-point touch sensor, higher capacitance was obtained when pressing wider-area touch points with 10mm to 25mm diameter on average. However, the capacitance of a system comprising two sheets of touch sensors was considerably low, causing a serious overlap of the capacitance values according to the data collected from the reliability test. Although the capacitance values could be increased by stacking several sheets of touch sensors, the overlap of data was still observed. After reducing the size of all touch points to 10mm and stacking up to eight sheets of sensors, reliable and consistent capacitance data was obtained. Five different capacitance signals could be induced in the sensors by pushing touch points simultaneously.

• 마이크로전자및패키징학회지
• /
• 제28권2호
• /
• pp.1-12
• /
• 2021

3차원 인쇄 기술은 제품의 설계를 3차원으로 하여 조립없이 제품의 생산까지의 시간을 획기적으로 줄이고 복잡한 구조도 구현할 수 있어 미래의 기술로 각광받고 있다. 본 논문은 3차원 인쇄기술을 이용한 전자소자에 대한 최근 연구동향을 알아보면서 구성품, 전원공급장치와 회로에서의 연결과 3차원 인쇄기술 PCB의 응용한 연구논문들을 소개하고 있다. 3차원 인쇄기술로 제작한 전자소자는 원스톱으로 전자소자, 솔더링(soldering), 스태킹(stacking), 회로의 봉지막(encapsulation)까지 제작함으로써 생산설비의 단순화와 전자기기를 개인 맞춤형을 할 수 있는 가능성을 보여주었다.