• New & Renewable Energy
• /
• v.10 no.2
• /
• pp.5-11
• /
• 2014

Squirrel cage induction motor is the main driving system of industrial field and familiar with its use in a large variety of applications. The structure and operating characteristics of induction generator is almost identical to induction motor, but the induction generator part is used restrictively from hydropower power and wind power development etc. Recently induction generator is commonly used for micro & small hydro power applications due to its simplicity, reliability, low cost and robustness. Input and output of induction motor has turned against at the induction generator operation. Rotation speed of induction generator is small faster than synchronous speed of induction motor. As output of induction machines increases with the increasement of speed, so loss is same. Actually, generator efficiency is lower than motor at this condition. If induction generator is connected with mechanical load such as increaser, total efficiency is decreased. Consequently the quality in compliance with an induction motor parameter applying like that in the generator is a possibility of having the error of some. In this paper, we analyzed that input, output, torque and efficiency of induction machine is different from each other above and below synchronous speed.

• Proceedings of the Korean Society of Applied Pharmacology
• /
• 2007.04a
• /
• pp.25-44
• /
• 2007

The glucocorticoid receptor (GR) is an intracellular protein that is widely distributed throughout hippocampal and neocortical brain tissue. Mifepristone (RU486) is a potent GR antagonist that has also been shown to exhibit partial agonist-like effects. The precise location of the GR domain involved in the agonist-like activity of RU486 is unknown. Here, we examine this aspect of GR signaling by comparing human GR (hGR) construct with a Guyanese squirrel monkey GR (gsmGR) construct in which nuclear translocation and transactivation are known to be impaired. Using an objective translocation scoring method, we found that both hGR and gsmGR are translocated by RU486, and that nuclear translocation of hGR is significantly increased compared to gsmGR at 10 nM, 100 nM and 1000 nM RU486 in transiently transfected COS1 cells. While addition of RU486 to the cells transfected with hGR results in a 16-fold dose-dependent increase in transactivation compared to non-treated cells, no significant change in transactivation is observed with gsmGR at doses up to 100 nM RU486. Further experiments using six GR chimeras indicate that replacement of the hGR carboxyl-terminus of tau-1 transactivation domain (C-AF1, amino acids 132-428) with that from gsmGR diminishes hGR transactivation by RU486. These results demonstrate that RU486-induced transactivation of GR is determined in part by amino acids in the C-AF1 domain.

• Journal of Korea Foundry Society
• /
• v.26 no.1
• /
• pp.40-45
• /
• 2006

Most of the work reported concerned the semi-solid processing of low melting point alloys, and in particular light alloys of aluminum and magnesium. The purpose of this paper is to develop a semi-solid microstructure of Cu alloys using electromagnetic stirring applicable for squirrel cage rotor of induction motor. The size of primary solid particle and the degree of sphericity as a function of the variation in cooling rate, stirring speed, and holding time were observed. By applying electromagnetic stirring, primary solid particles became finer and rounder relative to as-cast sample. As the input frequency increased from 30 to 40 Hz, particle size decreased. The size of primary solid particle was found to be decreased with increasing cooling rate. Also, it decreased with stirring up to 3 minutes but increased above that point. The degree of sphericity became closer to be 1 with hold time. Semi-solid microstructure of Cu alloys, one of the high melting point alloys, could be controlled by electromagnetic stirring.

• Proceedings of the KIEE Conference
• /
• 2006.07b
• /
• pp.739-740
• /
• 2006

According to the rapid growth of high speed and precise industry, the application of synchronous motor has been increased. In the application fields, the large synchronous motor is not a self-starting motor. The rotor is heavy and, from a dead stop, it is impossible to bring the rotor into magnetic lock with the rotating magnetic field for this reason, all synchronous motor have some kinds of starting device. A simple starter is another motor which brings the rotor up to approximately 96 percent of it synchronous speed. The starting motor is disconnected and the rotor locks in step with the rotating field. The more commony used starting method is to have the rotor to include a squirrel cage indution winding. This indution winding brings the rotor almost to synchronous speed as an induction motor. So, this paper describes excessive condition interpretation of a exciter circuit to prevent starting failure of large synchronous motor. the large synchronous motor needs safety of it in accordance with operating frequent start and stop. the operating Problem point of synchronous motor appears potential element damage of Exciter circuit because synchronous motor is caused synchronous separation. hence we eliminate it and improve starting toque.

• Proceedings of the KIEE Conference
• /
• 1994.07a
• /
• pp.150-152
• /
• 1994

In this paper, the optimum shape design of stator slot of induction motors for iron loss reduction is proposed. To obtain the flux distribution in induction motors, 2-D finite element method with voltage source is employed. The iron loss is calculated from the iron loss data given by the iron manufacturer. To calculate the sensitivity of iron loss to shape variation, the sensitivity analysis of discrete approach is used. The proposed algorithm is applied to a 3-phase squirrel cage induction motor. The nodes at stator slot boundary of the induction motor are defined as design parameters. By controlling these parameters under the constant volume of iron, we can minimize the iron loss. Furthermore, the stator copper loss is reduced by increasing the slot area. So the stator slot area is determined at the point that the summation of iron loss and copper loss of stator is minimized. Since the constraint of constant volume of iron is nonlinear to the design parameters, the Gradient Projection method is used as an optimization algorithm.

• Proceedings of the KIEE Conference
• /
• 1994.07a
• /
• pp.208-210
• /
• 1994

In this paper, the design sensitivity evaluation based on the 2-dimensional finite clement discretization is presented for the voltage source and eddy current problem. And it is applied to the two shape design problems of the rotor slot of 3-phase squirrel cage induction motors. The first is to increase the starting torque while keeping the rated torque fixed. The other is only to increase the torque at the rated speed while keeping the starting torque fixed. As an optimization method, the Gradient Projection method is used to control casily the torques for various speeds of rotor. One fourth of rotor is analyzed by using a semi-periodic boundary condition. Because the shape of rotor slot has much influence on the slip torque characteristic, the 10 design parameters are taken on the interface between rotor core and rotor bar. The initial shape of rotor slot is the trapezoidal typo with rounding corners.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.35 no.1
• /
• pp.26-35
• /
• 1986

In this paper, non-linear state equations for a 3-phase, 220V, 0.4 KW, squirrel cage induction motor have been derived using the d-q transformation and then these equations have been linearized around an operating point by a small perturbation method. Root loci on the s-plane with repect to the changes of slip S and supply frequency f have been studied. Based on the above results, the derived linear state equations have been augmented to the 6th order, including the output velocity feedback and a discrete PI speed controller. Using the new state equations, stability regions on the Kp-Kl plane have been investigated for slip S and sampling time T. In designing a discrete PI controller, the coefficients Kp and Kl around the normal operating point (220V,1,692rpm,60Hz)have been chosen under the assumptions that each response to a perturbation input of reference speed and load torque be underdamped and dominated by a pair of complex poles. Step responses in the experimental system using an Intel SDK-86 and an optimized PWM inverter show satisfactory results that the maximum overshoots and damped frequency are well coincided with ones from the computer simulation.

• Proceedings of the KSME Conference
• /
• 2004.04a
• /
• pp.1058-1063
• /
• 2004

This paper presents a new approach regarding thermal characteristics associated with a design of the high efficiency motor. Electrical conduction materials, such as coil and aluminum embedded in the core generate high heat exerting negative influence on both lifetime and performance of machine. Thus, it is necessary to design high efficiency motor considering heat transfer in order to improve motor performance and to be protected against overheating. In this paper, firstly, numerical analysis of electromagnetic field is carried out by the nonlinear transient finite element method (FEM). Secondly, the linear static FEA of magneto-thermal field is implemented by applying source current computed by the nonlinear transient analysis. FE results are validated in terms of electromagnetics and heat transfer by experiments. And then, the pseudo-transient topology optimization using a multi-objective function is performed. The proposed method is applied to a squirrel cage single-phase induction motor of the scroll compressor.

• The Korean Journal of Zoology
• /
• v.32 no.1
• /
• pp.14-21
• /
• 1989

Four external and 22 cranial characters of 279 specimens representing 24 species of six orders of Korean mammals were measured. The data were analyzed by phenetic methods such as ordination as well as clustering techniques. Morphological distances were also calculated. Phenetic studies yield taxonomic placements of Siberian mink, Palearetic squirrel, and big white-toothed shrew which are incorrect. Morphological differences among Korean mammals at ordinal level in the taxonomic hierarchy are larger than those among other mammals: morphological differences below ordinal level are comparable to those among other mammals. Average taxonomic distances and morphological differences among Korean mammals at various levels in the taxonomic hierarchy are jointly monotonic, although the value of Pearson's product-moment correlation coefficient between average taxonomic distance matrix and morphological difference marrix is 0.59.

• Animal cells and systems
• /
• v.7 no.2
• /
• pp.123-125
• /
• 2003

We studied the nectar secretion of the Japanese Camellia (Camellia japonica L.), an evergreen tree and observed its floral visitors during the day. The mean volume of nectar secreted, during daylight (08:31 to 16:30 h) was 30.26$\pm8,29ml$ (SD) (n = 27). During the late afternoon and overnight (16:31 to 08:30 following day), 100.54$\pm54.85$(n = 27) of nectar was secreted. Total volume measured when flowers were sampled once every two hours for an eight-hour period was approximately one-half the volume which was measured when the flowers were sampled only once after eight hours. The mean nectar volume secreted was 8.55$\pm8.3ml$(n = 30) between 08:31 to 10:30, 4.38$\pm$6.1 ml (n = 30) between 10:31 to 12:30, 4.6$\pm5.4ml$(n = 30) between 12;31 to 14:30, and 4.02$\pm3.5ml$(n = 30) between 14:31 to 16:30 hours. During the day, Japanese Camellia flowers were principally visited by the Japanese white-eye (Zosterops erythropleura erythropleura 5.), a native bird, although insects and squirrels also visited to a lesser degree.