• Journal of radiological science and technology
• /
• v.39 no.4
• /
• pp.615-622
• /
• 2016

The 18~20G needle is used to computer tomography (CT) contrast examination. Therefore, a patient has to apply a self-administering hemostasis (conventional method: CM) and often experience bleeding in the course. Thus, we developed the new disposable transparent tourniquet (TT) for reducing. This study was to compare the usefulness between the proposed transparent tourniquet and the existing hemostatic methods. A Satisfaction survey was conducted by 50 patients and 25nurses. The survey contained the satisfaction of the convenience, safety, sanitation, and wearing sensation of transparent tourniquet. We employed face-to-face interview on 5 points likert scales. And Chi-square, paired T-test were used for the statistics verification. As for the patients, the satisfaction levels were measured for each category with the gender, age. Patients evaluation, overall satisfaction high average sore used TT and there were statistical significance by paired T-test(p<0.05). The following is the average satisfaction level for each category: $4.4{\pm}0.53$ in; $4.28{\pm}0.57$ in safety; $4.52{\pm}0.54$ in sanitation; $4.16{\pm}0.54$ in wearing sensation. So the overall satisfaction level is measured at $4.34{\pm}0.51$. As for the nurses, CT work experience and the current satisfaction with tourniquet were counted as variables. The satisfaction level for each category is: $3.8{\pm}0.7$ in; $3.6{\pm}0.68$ in safety; $3.4{\pm}0.5$ in sanitation; $3.9{\pm}0.49$ in hemostasis. The overall satisfaction level is $3.8{\pm}0.3$. Patients' satisfaction levels were very high with little difference among variables. Nurses' satisfaction levels were different with the TT depending on their work experience but their overall satisfaction was high. This TT will be a starting point to minimizing patient's inconvenience and more studies are necessary to enhance their satisfaction.

• Korean Journal of Agricultural and Forest Meteorology
• /
• v.13 no.4
• /
• pp.176-184
• /
• 2011

Cold air on sloping surfaces flows down to the valley bottom in mountainous terrain at calm and clear nights. Based on the assumption that the cold air flow may be the same as the water flow, current models estimate temperature drop by regarding the cold air accumulation at a given location as the water-like free drainage. At a closed catchment whose outlet is blocked by man-made obstacles such as banks and roads, however, the water-like free drainage assumption is no longer valid because the cold air accumulates from the bottom first. We developed an empirical model to estimate quantitatively the effect of cold pool on nocturnal temperature in a closed catchment. In our model, a closed catchment is treated like a "vessel", and a digital elevation model (DEM) was used to calculate the maximum capacity of the cold pool formed in a closed catchment. We introduce a topographical variable named "shape factor", which is the ratio of the cold air accumulation potential across the whole catchment area to the maximum capacity of the cold pool to describe the relative size of temperature drop at a wider range of catchment shapes. The shape factor is then used to simulate the density profile of cold pool formed in a given catchment based on a hypsometric equation. The cold lake module was incorporated with the existing model (i.e., Chung et al., 2006), generating a new model and predicting distribution of minimum temperature over closed catchments. We applied this model to Akyang valley (i.e., a typical closed catchment of 53 $km^2$ area) in the southern skirt of Mt. Jiri National Park where 12 automated weather stations (AWS) are operational. The performance of the model was evaluated based on the feasibility of delineating the temperature pattern accurately at cold pool forming at night. Overall, the model's ability of simulating the spatial pattern of lower temperature were improved especially at the valley bottom, showing a similar pattern of the estimated temperature with that of thermal images obtained across the valley at dawn (0520 to 0600 local standard time) of 17 May 2011. Error in temperature estimation, calculated with the root mean square error using the 10 low-lying AWSs, was substantially decreased from $1.30^{\circ}C$ with the existing model to $0.71^{\circ}C$ with the new model. These results suggest the feasibility of the new method in predicting the site-specific freeze and frost warning at a closed catchment.

• Korean Journal of Agricultural and Forest Meteorology
• /
• v.18 no.4
• /
• pp.233-241
• /
• 2016

Experiments were carried out to quantify the topographic effects on attenuation of sunshine in complex terrain and the results are expected to help convert the coarse resolution sunshine duration information provided by the Korea Meteorological Administration (KMA) into a detailed map reflecting the terrain characteristics of mountainous watershed. Hourly shaded relief images for one year, each pixel consisting of 0 to 255 brightness value, were constructed by applying techniques of shadow modeling and skyline analysis to the 3m resolution digital elevation model for an experimental watershed on the southern slope of Mt. Jiri in Korea. By using a bimetal sunshine recorder, sunshine duration was measured at three points with different terrain conditions in the watershed from May 15, 2015 to May 14, 2016. The brightness values of the 3 corresponding pixel points on the shaded relief map were extracted and regressed to the measured sunshine duration, resulting in a brightness-sunshine duration response curve for a clear day. We devised a method to calibrate this curve equation according to sky condition categorized by cloud amount and used it to derive an empirical model for estimating sunshine duration over a complex terrain. When the performance of this model was compared with a conventional scheme for estimating sunshine duration over a horizontal plane, the estimation bias was improved remarkably and the root mean square error for daily sunshine hour was 1.7hr, which is a reduction by 37% from the conventional method. In order to apply this model to a given area, the clear-sky sunshine duration of each pixel should be produced on hourly intervals first, by driving the curve equation with the hourly shaded relief image of the area. Next, the cloud effect is corrected by 3-hourly 'sky condition' of the KMA digital forecast products. Finally, daily sunshine hour can be obtained by accumulating the hourly sunshine duration. A detailed sunshine duration distribution of 3m horizontal resolution was obtained by applying this procedure to the experimental watershed.

• Journal of the Korean Institute of Gas
• /
• v.17 no.4
• /
• pp.58-69
• /
• 2013

This paper presents production data analysis for two production wells located in the shale gas field, Canada, with the proper analysis method according to each production performance characteristics. In the case A production well, the analysis was performed by applying both time and superposition time because the production history has high variation. Firstly, the flow regimes were classified with a log-log plot, and as a result, only the transient flow was appeared. Then the area of simulated reservoir volume (SRV) analyzed based on flowing material balance plot was calculated to 180 acres of time, and 240 acres of superposition time. And the original gas in place (OGIP) also was estimated to 15, 20 Bscf, respectively. However, as the area of SRV was not analyzed with the boundary dominated flow data, it was regarded as the minimum one. Therefore, the production forecasting was conducted according to variation of b exponent and the area of SRV. As a result, estimated ultimate recovery (EUR) increased 1.2 and 1.4 times respectively depending on b exponent, which was 0.5 and 1. In addition, as the area of SRV increased from 240 to 360 acres, EUR increased 1.3 times. In the case B production well, the formation compressibility and permeability depending on the overburden were applied to the analysis of the overpressured reservoir. In comparison of the case that applied geomechanical factors and the case that did not, the area of SRV was increased 1.4 times, OGIP was increased 1.5 times respectively. As a result of analysis, the prediction of future productivity including OGIP and EUR may be quite different depending on the analysis method. Thus, it was found that proper analysis methods, such as pseudo-time, superposition time, geomechanical factors, need to be applied depending on the production data to gain accurate results.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2000.11a
• /
• pp.3-4
• /
• 2000

Many researchers are interested in the synthesis and characterization of carbon nitride and diamond-like carbon (DLq because they show excellent mechanical properties such as low friction and high wear resistance and excellent electrical properties such as controllable electical resistivity and good field electron emission. We have deposited amorphous carbon nitride (a-C:N) thin films and DLC thin films by shielded arc ion plating (SAIP) and evaluated the structural and tribological properties. The application of appropriate negative bias on substrates is effective to increase the film hardness and wear resistance. This paper reports on the deposition and tribological OLC films in relation to the substrate bias voltage (Vs). films are compared with those of the OLC films. A high purity sintered graphite target was mounted on a cathode as a carbon source. Nitrogen or argon was introduced into a deposition chamber through each mass flow controller. After the initiation of an arc plasma at 60 A and 1 Pa, the target surface was heated and evaporated by the plasma. Carbon atoms and clusters evaporated from the target were ionized partially and reacted with activated nitrogen species, and a carbon nitride film was deposited onto a Si (100) substrate when we used nitrogen as a reactant gas. The surface of the growing film also reacted with activated nitrogen species. Carbon macropartic1es (0.1 -100 maicro-m) evaporated from the target at the same time were not ionized and did not react fully with nitrogen species. These macroparticles interfered with the formation of the carbon nitride film. Therefore we set a shielding plate made of stainless steel between the target and the substrate to trap the macropartic1es. This shielding method is very effective to prepare smooth a-CN films. We, therefore, call this method "shielded arc ion plating (SAIP)". For the deposition of DLC films we used argon instead of nitrogen. Films of about 150 nm in thickness were deposited onto Si substrates. Their structures, chemical compositions and chemical bonding states were analyzed by using X-ray diffraction, Raman spectroscopy, X-ray photoelectron spectroscopy and infrared spectroscopy. Hardness of the films was measured with a nanointender interfaced with an atomic force microscope (AFM). A Berkovich-type diamond tip whose radius was less than 100 nm was used for the measurement. A force-displacement curve of each film was measured at a peak load force of 250 maicro-N. Load, hold and unload times for each indentation were 2.5, 0 and 2.5 s, respectively. Hardness of each film was determined from five force-displacement curves. Wear resistance of the films was analyzed as follows. First, each film surface was scanned with the diamond tip at a constant load force of 20 maicro-N. The tip scanning was repeated 30 times in a 1 urn-square region with 512 lines at a scanning rate of 2 um/ s. After this tip-scanning, the film surface was observed in the AFM mode at a constant force of 5 maicro-N with the same Berkovich-type tip. The hardness of a-CN films was less dependent on Vs. The hardness of the film deposited at Vs=O V in a nitrogen plasma was about 10 GPa and almost similar to that of Si. It slightly increased to 12 - 15 GPa when a bias voltage of -100 - -500 V was applied to the substrate with showing its maximum at Vs=-300 V. The film deposited at Vs=O V was least wear resistant which was consistent with its lowest hardness. The biased films became more wear resistant. Particularly the film deposited at Vs=-300 V showed remarkable wear resistance. Its wear depth was too shallow to be measured with AFM. On the other hand, the DLC film, deposited at Vs=-l00 V in an argon plasma, whose hardness was 35 GPa was obviously worn under the same wear test conditions. The a-C:N films show higher wear resistance than DLC films and are useful for wear resistant coatings on various mechanical and electronic parts.nic parts.

• Journal of The Korean Society of Grassland and Forage Science
• /
• v.31 no.3
• /
• pp.295-304
• /
• 2011

This study was carried out to investigate the effect of harvest stage of Sorghum ${\times}$ Sorghum Hybrid (SSH) and manufacture methods of SSH silage on nutritive values and quality of SSH silage manufactured with SSH grown in paddy land of Department of Animal Resources Development, National Institute of Animal Science, RDA. SSH "SS405" was harvested at two different growth stages (heading and ripen stage) and ensiled at each harvest stages. The content of crude protein in both square baled SSH silage (SBSS) and bag silage (BS) increased with delayed harvest maturity, but the contents of ADF (acid detergent fiber), NDF (neutral detergent fiber) decreased. The contents of ADF and NDF was not influenced by the inoculation of lactic bacteria. The contents of TDN (total digestible nutrient) in both stage and in vitro dry matter digestibility (IVDMD) in heading stage was not influenced by the harvest stage of SSH. The pH in all SSH silage ranged from 3.8 to 4.4 at two different harvest stages, and pH in heading stage was higher than that of ripen stage (P<0.05). The content of lactic acid of all SSH silage increased with delayed harvest maturity (P<0.05), but the content of acetic acid decreased (P<0.05). The contents of lactic acid and acetic acid in ripen stage were not influenced by manufacture method of silage. The content of lactic acid in both SBSS was higher than that of both BS and RBSS in heading and ripen stage (P<0.05), but the content of acetic acid decreased (P<0.05). The contents of lactic acid and acetic acid in BS were similar as compared to that of RBSS. Therefore, we suggest that the quality of SSH silage in both heading and ripen stage can be improved by manufacture methods of SBSS and BS.

• Korean Journal of Optics and Photonics
• /
• v.28 no.3
• /
• pp.108-115
• /
• 2017

We report the assembly procedure and performance evaluation of a visible and near-infrared spectrometer in the wavelength region of 400-900 nm, which is later to be combined with fore-optics (a telescope) to form a f/2.5 imaging spectrometer with a field of view of ${\pm}7.68^{\circ}$. The detector at the final image plane is a $640{\times}480$ charge-coupled device with a $24{\mu}m$ pixel size. The spectrometer is in an Offner relay configuration consisting of two concentric, spherical mirrors, the secondary of which is replaced by a convex grating mirror. A double-pass test method with an interferometer is often applied in the assembly process of precision optics, but was excluded from our study due to a large residual wavefront error (WFE) in optical design of 210 nm ($0.35{\lambda}$ at 600 nm) root-mean-square (RMS). This results in a single-path test method with a Shack-Hartmann sensor. The final assembly was tested to have a RMS WFE increase of less than 90 nm over the entire field of view, a keystone of 0.08 pixels, a smile of 1.13 pixels and a spectral resolution of 4.32 nm. During the procedure, we confirmed the validity of using a Shack-Hartmann wavefront sensor to monitor alignment in the assembly of an Offner-like spectrometer.

• Journal of Korea Water Resources Association
• /
• v.54 no.12
• /
• pp.1243-1254
• /
• 2021

For water resources operation or agricultural water management, it is important to accurately predict evapotranspiration for a long-term future over a seasonal or monthly basis. In this study, reference evapotranspiration forecast (up to 12 months in advance) was performed using statistically predicted monthly temperatures and temperature-based Hamon method for the Han River basin. First, the daily maximum and minimum temperature data for 15 meterological stations in the basin were derived by spatial-temporal downscaling the monthly temperature forecasts. The results of goodness-of-fit test for the downscaled temperature data at each site showed that the percent bias (PBIAS) ranged from 1.3 to 6.9%, the ratio of the root mean square error to the standard deviation of the observations (RSR) ranged from 0.22 to 0.27, the Nash-Sutcliffe efficiency (NSE) ranged from 0.93 to 0.95, and the Pearson correlation coefficient (r) ranged from 0.97 to 0.98 for the monthly average daily maximum temperature. And for the monthly average daily minimum temperature, PBIAS was 7.8 to 44.7%, RSR was 0.21 to 0.25, NSE was 0.94 to 0.96, and r was 0.98 to 0.99. The difference by site was not large, and the downscaled results were similar to the observations. In the results of comparing the forecasted reference evapotranspiration calculated using the downscaled data with the observed values for the entire region, PBIAS was 2.2 to 5.4%, RSR was 0.21 to 0.28, NSE was 0.92 to 0.96, and r was 0.96 to 0.98, indicating a very high fit. Due to the characteristics of the statistical models and uncertainty in the downscaling process, the predicted reference evapotranspiration may slightly deviate from the observed value in some periods when temperatures completely different from the past are observed. However, considering that it is a forecast result for the future period, it will be sufficiently useful as information for the evaluation or operation of water resources in the future.

• (The)Study of the Eastern Classic
• /
• no.68
• /
• pp.173-208
• /
• 2017

This study sorted out the political methods of the typical shell-and-bone inscriptions during early Western Zhou, the shapes and arrangements of Chan, Chak, and Jak, and the characteristics and description methods of shell-and-bone characters and also investigated the formation backgrounds and changing patterns of shell-and-bone inscriptions with a focus on the transmitted literature and actual shell-and-bone inscriptions. First, the transmitted literature contained records saying that Gogongdanbu told fortunes by burning tortoise shells during Proto-Zhou, but no Bokgap from those days had been excavated yet. The content of the divination focused on the periods of Kings Wen, Wu, and Cheng of Zhou, and the shell-and-bone characters of Juwon contained much content about Jugong those days. Second, there were some differences in the processing methods between Bokgap and Bokgol, but their origin could basically be found in the Joyeongjang form during middle Shang. In addition, it was found that they directly accepted the Bukchon type of Seomseo during late Shang and the divination method of the Proto-Zhou culture. Third, all of Bokgaps had a set of square Chan and rectangular Chak installed on the back, whereas all of Bokgols had a set of circular Chan and vertically thin Chak and were in the shape of a cat's eye. In terms of the Chan, Chak, and Jak arrangement, the Bokgaps were similar to those of Yinxu during late Shang, whereas the Bokgols had the characteristics of the Joyeongjang type during middle Shang. Finally, there were differences in the description methods of shell-and-bone characters according to the arrangement methods of shell-and-bone inscriptions. Some rules were found according to each of the parts. Bokgaps were placed horizontally so that Gapsu would face sideways. The middle sections of Bokgols were mostly placed horizontally with the Byeongbu and Seonbu facing downwards at Golgu to write downwards from right to left. This method was estimated to have something to do with "Sigo" in the divination process in The Rites of Zhou. It was inferred that the perceptions of divination changed in the process of arranging the rites and music institutions during early Western Zhou.

• Proceedings of the Korean Society of Crop Science Conference
• /
• 2022.10a
• /
• pp.19-19
• /
• 2022

Hulled and naked oat is a perspective crop for the low input production systems due to its low requirements for soil quality and nutrition. Oats have good competitive ability against weeds and can provide appropriate yield in organic farming in comparison with other cereal species such as wheat or barley. It is a perspective crop from the point of view of use in the food industry too. The aim of our study was to compare the production and quality parameters of naked and hulled oat grown in both organic (OF) and conventional fields (CF). Small plot trials were conducted in two locations in the Czech Republic (České Budějovice, Prague) for four years (2018-2021) in two production systems (OF, and CF). We used four varieties of hulled oat (Korok, Kertag, Raven, Seldon) and one variety of naked oat (Patrik). During the vegetation, agronomically important data were recorded. After harvest samples were processed in the laboratory and analyzed selected quality parameters of grain dry matter (the protein content was determined by the Kjeldahl method, starch content in grain according to Ewers, fat content in grain dry matter by the modified method according to Soxhlet, and ash content in grain dry matter). The data were evaluated using the program STATISTICA version 13.2, StatSoft, Inc., California, USA. It is clear from the results that the number of panicles before the harvest was influenced by the location, cultivation system, year, and, to a lesser extent, the influence of the variety. The number of panicles in OF averaged 340 per square meter, which was 90% of the value of CF. For thousand grain weight (TGW), a significantly predominant effect of year was found. The independent effect of location on TGW was statistically not significant. Grain yield was predominantly influenced by cultivation system and location. In OF, it reached an average of 3.97 t.ha^-1, which was 75% of the yield of CF. As part of the evaluation of the basic grain quality indicators, the content of protein, starch, fat, and ash in the dry matter of the grain was evaluated. The content of protein in the dry matter of the grain was predominantly influenced by year, followed by the influence of the variety and a fairly comparable influence of the cultivation system and locality. On average, it achieved 16.05% in OF and 17.01% in CF. The starch content was then related to the protein content, where as a result of the lower protein content in the grain of OF oats, the content of starch and fat was on the contrary increased. The year turned out to be the most significant factor, affecting both the starch content in the dry matter of the grain and the fat content. This was followed again by a fairly comparable influence on the cultivation system and locality. The influence of the cultivation system and location was not statistically significantly applied in the case of ash content in dry matter. Based on our results we can propose both types of oat (hulled and naked) as perspective crops for OF. An organic farmer can expect to achieve stable yields which, in less favorable conditions for the production of cereals in the OF, may be close to the level of conventional yields. In the future, it will be important to change agrotechnology in OF and increase oat yield because this crop has a good potential to grow in areas with low nitrogen input or less fertile soil.