• Proceedings of the KIEE Conference
• /
• 1999.07d
• /
• pp.1683-1685
• /
• 1999

ITO films on plastic substrate were prepared by DC magnetron sputtering method using powdery target and their properties were investigated as a function of the deposition conditions. As the sputtering power and total pressure were higher, the resistivity of ITO films increased. The optical transmittance deteriorated with increasing sputtering power and thickness. As the total pressure increased, however, the optical transmittance improved at visible region of light. From these results, we could deposited ITO films with $8{\times}10^{-3}{\Omega}-cm$ of resistivity and 80% of transmittance at optimal conditions.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1997.04a
• /
• pp.188-193
• /
• 1997

ZnO thin film had been deposited on the glass 7r sputtering method, and investigated by electrical and structural properties. When the rf power was 188W and sputtering pressure was 1$\times$10$^{-3}$ Torr at room temperature, Al-doped ZnO thin film had the lowest resistivity(1$\times$10$^{-4}$ $\Omega$.cm), and then carrier concentration and Hall mobility were 6.27$\times$10$^{20}$ cm$^{-3}$ and 22.04$\textrm{cm}^2$/V.s, respectively. And undoped ZnO thin film had about 10$^{14}$ $\Omega$.cm resistivity when oxygen content was 10% or more at room temperature. The surface morphology of ZnO thin film observed by SEM was overall uniform when oxygen content was 50% below and sputtering pressure was 1.0$\times$10$^{-1}$ Torr.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.17 no.3
• /
• pp.278-282
• /
• 2004

The Hydrogenated amorphous carbon(a-C:H) thin films are deposited on silicon with a close field unbalanced magnetron(CFUBM) sputtering systems. The experimental data are obtained on the depositon rate and physical properties of a-C:H films using DC bias voltage and Ar/C$_2$H$_2$ pressure. The depostion rate and the surface roughness decrease with DC bias voltage, but the hardness of the thin films increases with DC bias voltage. And the position of G-peak moves to lower wavenumber indicating an increase in diamond-like carbon characteristics with the lower Ar/C$_2$H$_2$ pressure.

• Journal of Sensor Science and Technology
• /
• v.16 no.4
• /
• pp.301-306
• /
• 2007

AlN thin film for SAW filter application was deposited on (100) silicon wafers by reactive magnetron sputtering method. The structural characteristics were dependent on the deposition conditions such as sputtering pressure, RF power, substrate temperature, and nitrogen partial pressure. Scanning Electron Microscope (SEM), X-ray Diffraction (XRD), Electron Probe MicroAnalyzer (EPMA) and Atomic Force Microscope (AFM) have been used to find out structural properties and preferred orientation of AlN thin films. Insertion loss of SAW devices was 28.51 dB and out of band rejection was about 24 dB.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1999.11a
• /
• pp.419-422
• /
• 1999

We prepared CoCr thin film for perpendicular magnetic recording media by facing targets sputtering system(FTS system) which can deposit a high quality thin films in plasma-free state and wide range of working pressure. In this study, we investigated that the effect of sputtering condition , that Argon gas pressure and substrate temperature, on magnetic and crystallographic characteristic of CoCr thin film as well as the variation perpendicular coercivity in changing of film's thickness. Crystallographic and magnetic characteristic of prepared thin films were evaluated by x-ray fractometry(XRD), vibrating sample magnetometer(VSM) and kerr hysteresis loop measurement.

• Journal of the Korean institute of surface engineering
• /
• v.29 no.5
• /
• pp.424-429
• /
• 1996

Thin films of Ti-Ni alloy were formed by sputtering under various Ar gas pressures and r. f. powers to investigate the optimum sputtering conditions and to demonstrate their shape memory effect. The composition and structure of the films were examined by electron micro-probe analysis and scanning electron microscope. These films were annealed in order to crystallize them. The mechanical property of the annealed films was evaluated by a conventional bending test. The transformation tmeperatures were determined by differential scanning calorimetry. The shape memory behaviour was examined quantiatatively by changing in sample temperature under various constant loads. It was found that the Ar gas pressure had a critical effect on the mechanical property of the thin film,s although the r.f. power also affected it. The films formed at a high Ar gas pressure were too brittle to be bent successfully. However, the films formed at a low Ar gas pressur could be bent and their shape memory behavior was found to be comparable with that of bulk Ti-Ni alloys.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1997.11a
• /
• pp.173-176
• /
• 1997

The III-V nitride semiconductor InN thin films which have the direct bandgap in visible light wavelength region have been deposited on Si(100) substrates and AIN/Si(100) substrates by rf reactive sputtering. InN thin films have been investigated on the structural, and electrical properties according to the sputtering parameters such as total pressure, rf power, and substrate temperature. It is found that optimal conditions required for fabricating InN thin films with high crystal Quality, low carrier concentration, high Hall mobility are total pressure 5mTorr, rf power 60W, substrate temperature 6$0^{\circ}C$ . InN thin films deposited on the AIN(60min.)/Si(100) substrates arid AIN(120min.)/Si(100) substrates showed remarkably high crystal quality and electrical properties. It is known that AIN buffer layer is to decrease free energy at interface between InN film and Si substrate, and then promoting lateral growth of InN films.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.11a
• /
• pp.448-451
• /
• 2004

Vanadium oxides have been widely used in a variety of technological applications such electrochromic devices as infrared detectors and are expected as a material suitable for gas sensing applications. Thin films of Vanadium oxide (VOx) have been deposited by r.f magnetron sputtering under different oxygen partial pressure ratios and substrate temperatures. Humidity-sensitive properties of resistive sensors having interdigitated electrode structure are characterized. Our sensors show good response to humidity over 20%RH to 80%RH. Vanadium oxide films deposited with 0% $O_2$ partial pressure at foot exhibit greater sensitivity to humidity change than others.

• Proceedings of the Korean Society Of Semiconductor Equipment Technology
• /
• 2005.09a
• /
• pp.106-109
• /
• 2005

The ITO thin films for Top-Emitting Organic Light Emitting Devices (TOLEDs) were prepared on cell(LiF/Organic Layer/Bottom Electrode : ITO ) by FTS (Facing Targets Sputtering) system under different sputtering conditions which were varying gas pressure, input current and distance of target to target($D_{T-T}$). As a function of sputtering conditions, I-V characteristics of prepared ITO thin films on cell were measured by 4156A (HP). In the results, when the In thin films were deposited at $D_{T-T}$ 70mm and working pressure 1mTorr, the leakage current of ITO/cell was about 11[V] and 5E-6[$mA/cm^2$].

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.49 no.3
• /
• pp.149-154
• /
• 2000

Bi-layer Mo films were deposited on soda-lime glass substrates using DC magnetron supttering. Increasing gas pressure, the resistivity varied from $1\times10^{-5}\; to\; 8.3\times10^{-3}\; \Omega.cm$. Furthermore, stress direction yielded compressive-to-tensile transition stress curves. The micro-structure of the compressively-stressed film which had poor adhesion consists of tightly packed columns, but of the tensile-stressed films had less dense structure. Under all gas pressure conditions, Mo films exhibited distinctly increasing optical reflection with decreasing gas pressure. The expansion of (110) peak width with the gas pressure meant the worse crystalline growth. The impurity levels in the Mo film exhibited highly concentrated Na, Se and O elements due to less dense micro-structure. The degree of Na diffusion depends on the type of the glass substrate used and the nature of the Mo film.