• Journal of Ceramic Processing Research
• /
• v.13 no.spc2
• /
• pp.407-410
• /
• 2012

The properties of Al-doped ZnO (AZO) films were investigated as a function of H2/(Ar + H2) gas ratio using an AZO (2 wt% Al2O3) ceramic target in a radio frequency (RF) magnetron sputtering system. The deposition process was done at 200 ℃ and in 2 × 10-2Torr working pressure and with various ratios of H2/(Ar + H2) gas. During the AZO film deposition process, partial H2 gas affected the AZO film characteristics. The electron resistivity (~ 9.21 × 10-4 Ωcm) was lowest and mobility (~17.8 ㎠/Vs) was highest in AZO films when the H2/(Ar + H2) gas ratio was 2.5%. When the H2/(Ar + H2) gas ratio was increased above 2.5%, the electron resistivity increased and mobility decreased with increasing H2/(Ar + H2) gas ratio in AZO films. The carrier concentration increased with increasing H2/(Ar + H2) gas ratio from 0% to 7.5%. This phenomenon was explained by reaction of hydrogen and oxygen and additional formation of oxygen vacancy. The average optical transmission in the visible light wavelength region over 90% and an orientation of the deposition was [002] orientation for AZO films grown with all H2/(Ar + H2) gas ratios.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.8 no.3
• /
• pp.472-476
• /
• 2007

In this study, we investigated methods for p-type ZnO deposition as well as stability enhancement of its properties. The film was prepared by co-depositing AlAs and ZnO in a RF magnetron sputtering system. Property variation was monitored with photoluminescence and Hall measurements by stressing the films at $250^{\circ}C$ for various duration upto 144 hours. Results indicated that co-deposition is a useful method for p-type ZnO preparation. In particular, pre-treatment in 30% $H_2O_2$ for 1min was observed to be effective in reducing the property variation taking place during the subsequent high temperature processes.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.319-319
• /
• 2013

Even though the fabrication methods of metal oxide based thin film capacitor have been well established such as RF sputtering, Sol-gel, metal organic chemical vapor deposition (MOCVD), ion beam assisted deposition (IBAD) and pulsed laser deposition (PLD), an applicable capacitor of printed circuit board (PCB) has not realized yet by these methods. Barium Strontium Titanate (BST) and other high-k ceramic oxides are important materials used in integrated passive devices, multi-chip modules (MCM), high-density interconnect, and chip-scale packaging. Thin film multi-layer technology is strongly demanded for having high capacitance (120 nF/$mm^2$). In this study, we suggest novel multi-layer thin film capacitor design and fabrication technology utilized by plasma assisted deposition and photolithography processes. Ba0.6Sr0.4TiO3 (BST) was used for the dielectric material since it has high dielectric constant and low dielectric loss. 5-layered BST and Pt thin films with multi-layer sandwich structures were formed on Pt/Ti/$SiO_2$/Si substrate by RF-magnetron sputtering and DC-sputtering. Pt electrodes and BST layers were patterned to reveal internal electrodes by photolithography. SiO2 passivation layer was deposited by plasma-enhanced chemical vapor deposition (PE-CVD). The passivation layer plays an important role to prevent short connection between the electrodes. It was patterned to create holes for the connection between internal electrodes and external electrodes by reactive-ion etching (RIE). External contact pads were formed by Pt electrodes. The microstructure and dielectric characteristics of the capacitors were investigated by scanning electron microscopy (SEM) and impedance analyzer, respectively. In conclusion, the 0402 sized thin film multi-layer capacitors have been demonstrated, which have capacitance of 10 nF. They are expected to be used for decoupling purpose and have been fabricated with high yield.

• Current Photovoltaic Research
• /
• v.8 no.1
• /
• pp.33-38
• /
• 2020

Single-phased SnS thin films have been prepared by RF magnetron sputtering at various deposition pressures. The effect of deposition pressure on the structural and optical properties of polycrystalline SnS thin films was studied using X-ray diffraction (XRD), field-emission scanning electron microscopy (FE-SEM), X-ray photoelectron spectroscopy (XPS) and ultraviolet-visible-near infrared (UV-Vis-NIR) spectrophotometer. The XRD analysis revealed the orthorhombic structure of the SnS thin films oriented along the (111) plane direction. As the deposition pressure was increased from 5 mTorr to 15 mTorr, the intensity of the peak on the (111) plane increased, and the intensity decreased under the condition of 20 mTorr. The binding energy difference at the Sn 3d_5/2 and S 2p_3/2 core levels was about 324.5 eV, indicating that the SnS thin film was prepared as a pure Sn-S phase. The optical properties of the SnS thin films indicate the presence of direct allowed transitions with corresponding energy band gap in the rang 1.47-1.57 eV.

• Journal of Surface Science and Engineering
• /
• v.47 no.3
• /
• pp.109-115
• /
• 2014

High power impulse magnetron sputtering (HIPIMS), also known as the technology is called peak power density in a short period, you can get high, so high ionization sputtering rate can make. Higher ionization of sputtered species to a variety of coating materials conventional in the field of improving the characteristics and self-assisted ion thin film deposition process, which contributes to a superior being. HIPIMS at the same power, but the deposition speed is slow in comparison with DC disadvantages. Since recently as a replacement for HIPIMS modulated pulse power (MPP) has been developed. This ionization rate of the sputtered species can increase the deposition rate is lowered and at the same time to overcome the problems to be reported. The differences between the MPP and the HIPIMS is a simple single pulse with a HIPIMS whereas, MPP is 3 ms in pulse length is adjustable, with the full set of multi-pulses within the pulse period and the pulse is applied can be micro advantages. In this experiment, $In_2O_3$ : $SnO_2$ composition ratio of 9 : 1 wt% target was used, Ar : $O_2$ flow rate ratio is 4.8 to 13.0% of the rate of deposition was carried out at room temperature. Ar 40 sccm and the flow rate of $O_2$ and then fixed 2 ~ 6 sccm was compared against that. The thickness of the thin film deposition is fixed at 60 nm, when the partial pressure of oxygen at 9.1%, the specific resistance value of $4.565{\times}10^{-4}{\Omega}cm$, transmittance 86.6%, mobility $32.29cm^2/Vs$ to obtain the value.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2011.05a
• /
• pp.139-139
• /
• 2011

DC magnetron sputtering과 DC pulsed magnetron sputtering을 이용하여 공정 압력별, $O_2$ 분압별, 온도등의 증착조건에 따른 IGZO 박막의 특성을 조사하였다. Working pressure 따른 deposition rate 측정한 결과 동일 파워 적용 시 DC magnetron sputtering 대비하여 DC pulsed magnetron sputtering 은 약 84% 수준에 머물렀으며, IGZO 박막 내에 $O_2$의 분압비가 증가함에 따라 투과도는 단파장 영역에서 장파장 영역으로 갈수록 상승 경향을 보였다. 캐리어 농도와 이동도 등 전기적 특성도 증가하는 경향을 보였다. 온도에 따른 전기적 특성을 비교 해 본 결과 상온과 $150^{\circ}C$ 영역에서는 유의차가 없었으며, DC pulsed magnetron sputtering의 경우 $50^{\circ}C$ 영역에서 변곡점이 형성됨을 알수 있었다.

• Journal of the Semiconductor & Display Technology
• /
• v.9 no.3
• /
• pp.23-27
• /
• 2010

We prepared Al doped ZnO thin film as a top electrode on a glass substrate with a deposited $Alq_3$ for the top emission organic Light emitting device (TEOLED) with facing target sputtering (FTS) method and radio-frequency (RF) sputtering method, respectively. Before the deposition of AZO thin film, we evaporated the $Alq_3$ on glass substrate by thermal evaporation. And we evaluated the damage of organic layer. As a result, PL intensity of $Alq_3$ on grown by FTS method showed higher than that of grown by RF sputtering method, so we found that the FTS showed the lower damage sputtering than RF sputtering. Therefore, we can expect the FTS method is promising the low-damage sputtering system that can be used as a direct sputtering on the organic layer.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.05d
• /
• pp.45-48
• /
• 2003

BiSrCaCuO thin films were fabricated by atomic layer-by-layer deposition using an ion beam sputtering method. 10 wt% and 90 wt% ozone mixed with oxygen were used with ultraviolet light irradiation to assist oxidation. At early stages of the atomic layer by layer deposition, two dimensional epitaxial growth which covers the substrate surface would be suppressed by the stress and strain caused by the lattice misfit, then three dimensional growth takes place. Since Cu element is the most difficult to oxidize, only Sr and Bi react with each other predominantly, and forms a buffer layer on the substrate in an amorphous-like structure, which is changed to $SrBi_2O_4$ by in-situ anneal.

• Journal of Surface Science and Engineering
• /
• v.36 no.2
• /
• pp.122-127
• /
• 2003

Ti - Si - N hard films were deposited on SKD11 steel substrates by a hybrid deposition system, where TiN was deposited by AIP method while Si was incorporated by sputtering one. The microstructure of Ti-Si-N films was revealed to be a composite of TiN crystallites and amorphous Si3N4 by instrumental analyses. The highest hardness value of about 45 Gpa was obtained at the Si content of around 7.7 at.%. With increase of Si content, the size of TiN crystallites was reduced and their distribution was changed from aligned to randomly orientated states. Surface roughness of Ti-Si-N film also decreased with increase of Si content.

• Journal of information and communication convergence engineering
• /
• v.7 no.4
• /
• pp.530-534
• /
• 2009

C-axis-oriented ZnO thin films were successfully deposited on p-Si (100) in an RF magnetron sputtering system. Deposition conditions such as deposition power, working pressure, and oxygen gas ratio $O_2/(O_2+Ar)$ were varied. Crystalline structures of the deposited ZnO films were investigated by a scanning electron microscope (SEM) technique. Results show that the deposition parameters can have a strong impact on the preferred orientations and grain sizes of the deposited ZnO films.