• Journal of KSNVE
• /
• v.7 no.5
• /
• pp.853-860
• /
• 1997

For this study, the multi-degree of freedom analysis model of torsional vibration was developed. This model is combined with mass moment of inertia and torsional spring in two wheel drive and four wheel drive vehicle. We compared and analyzed torsional vibration characteristics by natural frequencies and mode shapes which are obtained by free vibration analysis of this model. And we studied torsional vibration contribution of driveline elements by performing the forced vibration analysis of engine excitation torque. The validity of this model is demonstrated by the field test. The reduction effect of the torsional vibration along the driveline design factor is presented by the analytical results.

• Transactions of Materials Processing
• /
• v.26 no.5
• /
• pp.277-285
• /
• 2017

Vehicle weight reduction is a known strategy to improve fuel efficiency and strengthen exhaust gas regulation. The use of high strength steel can satisfy safety, efficiency, emission, manufacturability, durability, and cost requirements. However, springback of high strength steel results in undesired shape defects. Springback is one of the most important issues of high strength steel for many applications in an automobile. Servo press has various capabilities to improve defects, process conditions, and productivity problems when forming a high strength steel. Especially, servo press can be set to function with variable slide motion in a single operation. In this study, the effect of servo press slide motion on 980MPa high strength steel was investigated through U-bending test.

• Proceedings of the KSR Conference
• /
• 1998.05a
• /
• pp.307-314
• /
• 1998

In this paper, a numerical method for analyzing the interactions between train and track is presented. The effect of track irregularity on high speed running trains and track is examined by parametric studies. Two types of vertical track irregularity are considered. The first one is ideally assumed to a sine wave to investigate train and track behaviors with the change of its shape feasibly, The second one is artificially generated from PSD of track irregularity which was established from the measured data on real railways. In the track dynamic model, rail is considered to have a distributed mass and to be supported discretely at sleepers above ballast divided into three layers. Then, the contact between wheel and rail is modeled by a nonlinear Hertzian spring.

• Transactions of Materials Processing
• /
• v.3 no.3
• /
• pp.347-358
• /
• 1994

The purpose of the study is to form $\Omega$-type bellows without any defect by specific rollers which are designed based on the volume distribution technique. In the present paper, we proposed a forming process of existing U-type bellows to a value-added $\Omega$-type in a progressive manner. It was developed to shape a perfect $\Omega$-type bellows after preforming from initial U-type bellows to final U-type bellows. To examine the suggested 'processing condition design' some experiments were performed in a real scale. It was found out that the spring back effect played a major role in deviating the geometry of formed bellows from the predicted one. The problems found in the experiment can be used as important information in manufacturing equipment for forming $\Omega$-type bellows.

• Journal of Power System Engineering
• /
• v.7 no.2
• /
• pp.66-72
• /
• 2003

Recently, the steel parts used at the aerospace and automobile industries are required to be used light weight parts. Therefore, used material, steel have to be a high stress, which is an indispensable condition in this field. At the consideration of parts design, high hardness of the lightweight parts have an benefit of saving fuel and material. A high stress of metal has a point of difference according to the shape of design, external cyclic load and condition of vibration. A crack generates on the surface of metal or under yield stress by defect of inner metal defect or surface defect and slowly, this crack grow stable growth. Finally, rapidity failure phenomena is happen. Fatigue failure_phenomena, which happen in metal, bring on danger in human life and property therefor, anti-fatigue failure technology take an important part of current industries Currently, the shot peening is used for removing the defect from the surface of steel and improving the fatigue strength on surface. Therefore, this paper investigated the effect on frcature toughness using shot peening which is improve the resistance of crack growth and crack expansion rate by fatigue that make a compressive residual stress on surface.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2003.11a
• /
• pp.64-71
• /
• 2003

In order to evaluate the effect of alloying elements (Nb and Sn) on the wear resistance of advanced Zr fuel claddings, sliding wear tests have been performed in room temperature air and water and these results were compared with those of commercial alloys such as Zircaloy-4, A and B alloys. As a result, the advanced Zr fuel claddings have a similar wear resistance compared with the commercial alloys. The wear resistance of the advanced Zr fuel claddings is closely releted to the content of Nb and Sn even though the effects of transition elements are involved in deforming wear properties. In the tested specimens with similar Sn content, wear volume became down to a minimum at $0.4\;wt\;\%$ Nb, then rapidly increased at 1.0 wt Nb. This behavior results in the variation of grain size with alloying contents. But Sn did not have a significant effect on the wear volume of advanced Zr fuel claddings below $1.1\;wt\%$. The relationship between alloying elements and wear behaviour was evaluated and discussed using material compatibility factor.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.30 no.4A
• /
• pp.353-359
• /
• 2010

Cementitious matrix based composites are vulnerable to the drying shrinkage crack during the curing process. In this study, the drying shrinkage induced fracture behavior of the fiber reinforced concrete is simulated and the effects of the fiber reinforcement conditions on the fracture characteristics are analysed. The numerical model is composed of conduit elements and rigid-body-spring elements on the identical irregular lattice topology, where the drying shrinkage is presented by the coupling of nonmechanical-mechanical behaviors handled by those respective element types. Semi-discrete fiber elements are applied within the rigid-body-spring network to model the fiber reinforcement. The shrinkage parameters are calibrated through the KS F 2424 free drying shrinkage test simulation and comparison of the time-shrinkage strain curves. Next, the KS F 2595 restrained drying shrinkage test is simulated for various fiber volume fractions and the numerical model is verified by comparison of the crack initiating time with the previous experimental results. In addition, the drying shrinkage cracking phenomenon is analysed with change in the length and the surface shape of the fibers, the measurement of the maximum crack width in the numerical experiment indicates the judgement of the crack controlling effect.

• Journal of the Korean Institute of Landscape Architecture
• /
• v.34 no.3 s.116
• /
• pp.79-90
• /
• 2006

Tamarix chinenis blooms twice a you and its flowers, branches and leaves make the adjustment of tree shape. Propagation methods and growth characteristics of T. chinensis were studied in order to ascertain its potential use as one of vegetation resources for coast forestation and landscaping. The study results indicated that 1 or 2 you old hard wood cuttings showed higher rooting ratio than greenwood or semi hard wood cuttings. One to one mixture between vermiculite and pearlite appeared to be the best for bed soil, and sea sand and silt(loess) mixture was the next. Sea sand and granitic soil followed after. In terms of seasonal differences, spring cuttings showed the best rooting ratio, root number, and root length. Fall cuttings followed after spring cutting, and summer cuttings showed worst results regarding rooting ratio, root number, and root length. The best rooting promotion effects of growth regulators were observed with sea sand bed soils. There was no significant difference among growth regulators in terms of rooting and shoot growth. Low concentration below 100 ppm of growth regulators was enough for rooting promotion effect. In general, the number and mean length of roots and shoots were showed the excellent records in the sites with high rooting ratio. The study result strongly showed that T. chinensis can be considered as a suitable tree for coast forestation and landscaping because of its easy cutting propagation and rapid growth on saline lands.

• Composites Research
• /
• v.34 no.6
• /
• pp.426-433
• /
• 2021

The carbon fiber reinforced plastic manufacturing process has a problem in that a dimensional error occurs due to thermal deformation such as residual stress, spring-in, and warpage. The main causes of thermal deformation are various, including the shape of the product, the chemical shrinkage, thermal expansion of the resin, and the mold effect according to the material and surface condition of the mold. In this study, a viscoelastic model was applied to the plate model to predict the thermal deformation. The effects of chemical shrinkage and thermal expansion of the resin, which are the main causes of thermal deformation, were analyzed, and the analysis technique of the 3-D viscoelastic model with and without mold was also studied. Then, the L-shaped mold effect was analyzed using the verified 3D viscoelastic model analysis technique. The results show that different residual deformation occurs depending on the surface condition even when the same mold is used.

• Tribology and Lubricants
• /
• v.15 no.3
• /
• pp.278-286
• /
• 1999

To predict the behavior of the intravascular micro active endoscope in the real human vascular system, a human mock circulation system was developed. The intravascular micro active endoscope which consists of micro active bending catheter and micro drug infusion catheter was driven in the velocity, Re number and temperature controlled flow. The three SMA (Shape Memory Alloy) zigzag type spring in the micro active bending catheter was heated by the electric current generated by PWM controller, and the shape memory effect made the actuator bend to any direction. The micro drug infusion catheter was driven through the inner hole of the micro active bending catheter. A mock circulation system is shaped from Ascending Arota to Femoral artery according to a human data (the data contains many vascular sizes and hydrographs of many control points). We developed a vascular model with glass and silicone tubes, and set the flow system with circulation parts, flow settling parts, and lots of valves. The heater and heat-controller was added to the How system to centre! the temperature of the How at 36.5$^{\circ}C$. The result showed that the developed intravascular micro active endoscope could be induced to any point in the vascular model.