• 수산해양기술연구
• /
• 제50권2호
• /
• pp.176-184
• /
• 2014

Nowadays, consumption of fisheries products is increasing. There are several factors, one of which is a quantitative development through aquaculture. Another factor is an increase qualitative consumption of fish which require that fish be supplied alive. This requires a lot of technical effort to transport the live fish that have low survival rate (c.f. tuna and mackerel) in coastal waters and in the open sea. To develop a towing cage for transporting the live fish, model test in a circulate water channel and simulation by computer tool were carried out. In order to spread vertically, floats were attached at the upper part of the cage, and iron chains attached at the lower part of the cage. For horizontal spreading, kites were attached on the cage. The tension and spreading performance of the cage were measured. The result shows that the tension and reduction ratio of inside volume of the cage were tended to increase with increased towing speeds. The suitable operation condition in towing cage was 1.0 m/s towing speeds with vertical spreading force 8.7 kN, horizontal spreading force 5.6 kN; in this case the reduction ratio of inside volume of the cage was estimated as 25%.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2003년도 봄 학술발표회 논문집
• /
• pp.767-772
• /
• 2003

The clay which transported into a pond under the high water content condition have no effective stress which develop from the starting point of sedimentation and self-weight consolidation. Since sedimentation and self-weight consolidation dependent on self-weight of solids is made progress over a long time, to accelerating it have many advantages in the economic view In this paper, sand spreading method which is one of sedimentation and self-weight consolidation acceleration method is studied through a series of experiments considering the mixing ratio of sand and clay. The test results show that the mixing ratio of clay and sand of 1:0.2 is the biggest rate of consolidation and the pouring at the end point of sedimentation considerably effects on consolidation rate.

• 한국전자파학회논문지
• /
• 제26권12호
• /
• pp.1091-1099
• /
• 2015

5세대 이동통신을 위한 후보 변조기술들로 다수의 부반송파를 사용하는 UFMC(Universal-Filtered Multi-carrier) 및 FBMC(Filter Bank Multi-carrier)가 주목받고 있다. 그러나 이러한 변조기술들은 다수의 부반송파 신호의 중첩으로 인하여 높은 PAPR(Peak to Average Power Ratio) 특성을 갖는다. 본 논문은 5세대 이동통신을 위한 후보 변조기술들의 PAPR 문제를 해결하기 위하여 DFT(Discrete Fourier Transform) spreading 기법을 응용한 DFT-s(spreading)-UFMC 및 DFT-s-FBMC 시스템을 제안한다. 제안하는 시스템들의 PAPR 성능을 비교 평가하기 위하여 기존의 OFDM(Orthogonal Frequency Division Multiplexing), UFMC, FBMC, DFT-s-OFDM 시스템과 제안하는 DFT-s-UFMC, DFT-s-FBMC 시스템을 설계하고, 시뮬레이션을 통해 신호 특성 확인과 PAPR 성능 평가 및 비교 분석을 수행하였다. 시뮬레이션의 결과로 DFT-s-OFDM과 같이 UFMC 및 FBMC에 DFT spreading 기법을 응용할 경우, 기존의 시스템 대비 각각 OFDM은 2.7 dB, UFMC는 2.8 dB, FBMC는 1.1 dB 정도 PAPR 성능이 향상되는 것을 확인하였다.

• 한국통신학회논문지
• /
• 제41권4호
• /
• pp.415-423
• /
• 2016

높은 PAPR(Peak-to-Average Power Ratio)은 HPA(High Power Amplifier) 비선형성에 의해 시스템의 성능을 열화 시키고, 스펙트럼의 OOB(Out-of-Band) 전력을 향상시키는 문제의 원인이 된다. 5세대 이동통신 시스템을 위한 후보변조기술로 UFMC(Universal Filtered Multi-Carrier) 및 FBMC(Filter Bank Multi-Carrier) 시스템이 있다. 본 논문에서는 PAPR 저감 기법으로 잘 알려진 DFT-s(Discrete Fourier Transform Spreading) 기법을 각 시스템에 적용하고, 비선형 HPA 환경에서 각각의 성능에 대하여 비교분석하였다. 우선, 본 논문에서는 OFDM(Orthogonal Frequency Division Multiplexing), UFMC, FBMC 시스템에 대해서 설명을 하며, 각 시스템에 DFT spreading 기법을 적용한 DFT-s-OFDM, DFT-s-UFMC, DFT-s-FBMC 시스템에 대해 설명한다. 본 논문에서는 비선형 모델로 Saleh 모델을 사용하였으며, 다양한 강도의 HPA 비선형성을 고려하여 시뮬레이션을 수행하였다. 시뮬레이션 결과, OFDM 및 UFMC 시스템의 경우 PAPR을 효과적으로 저감시킬 수 있으며, FBMC의 경우 PAPR 저감은 이루어지나 그 효과가 크지 않음을 확인하였다.

• 한국통신학회논문지
• /
• 제31권3A호
• /
• pp.214-220
• /
• 2006

본 논문에서는 TPC-AMS/FSS-OFDM(transmit power controlled adaptive modulated OFDM with frequency symbol spreading and equalization)시스템을 제안한다. TPC-AMS/FSS-OFDM의 송신기에서 각 S/P(serial-to-parallel)변환된 신호는 직교 확산 코드에 의해 확산 결합되어 송신하고, 수신된 신호는 수신기의 각 주파수 심볼 확산 블록에 의하여 검출되며, 같은 SINR(signal interference to noise ratio)을 얻는다. 이 때 각 주파수 심볼 확산블록에 대해서는 같은 변조 레벨과 송신 전력을 할당할 수 있다. 본 논문에서 제안한 시스템은 전체 송신 전력과 데이터 정보로 전송되는 FBI(feedback information), MLI(modulation level information)를 감소시킴으로서 전체적인 전송속도(throughput)의 성능을 개선할 수 있다.

• 열처리공학회지
• /
• 제22권4호
• /
• pp.210-216
• /
• 2009

Stainless steel EGR cooler of diesel engine is widely used to prevent the corrosion due to the content of sulfur in diesel fuel. The strength of brazed joint between stainless steel materials is very important. It is essential to observe the spreading ratio of the filler metals under the condition of deoxidation or vacuum during heating process. In this experiment, spreading ratio was tested to find the optimum brazing condition for stainless steel using brazing filler metals of FP-613, BNi-2 and BNi-5 on sus304 and sus410. Anti-corrosion tests were also performed on the above filler metals with solution of 5% $H_2SO_4$, 65% $HNO_3$ and 5% $NH_4OH$. Consequently FP-613 has good ability for anti-corrosion with 30% of chromium content compared with other filler metals. The optimum brazing conditions are occurred at $960^{\circ}C$ for 90 min. and at $1090^{\circ}C$ for 50 min. at the same degree of vacuum, $2{\sim}3{\times}10^{-3}$ Torr.

• Journal of Communications and Networks
• /
• 제10권1호
• /
• pp.71-78
• /
• 2008

We propose a sub-band spreading technique for adaptive modulation (AM) in orthogonal frequency division multiplexing (OFDM) systems in order to reduce signaling overheads and to average frequency selective fading channels causing different signal-to-noise ratio (SNR) values for subcarriers in each subband. The conventional sub-band based AM schemes can also reduce signaling overheads and complexity for allocating a resource per sub-band at a time. However, they may suffer from the channel variation in a sub-band when the sub-band size is larger than the channel coherence bandwidth (BW). The sub-band spreading at the transmitter enables the received symbols in each sub-band to have an identical reliability even in a frequency selective fading channel. We rigorously analyze the averaged SNR value at the receiver of the sub-band spreading system and the analyzed average SNR in a sub-band is used for an adaptation criterion. The proposed AM scheme outperforms the conventional sub-band based OFDM scheme without spreading, and it can yield better throughput performance than the conventional subcarrier based AM schemes when we consider the signaling overheads.

• Journal of the Korean Wood Science and Technology
• /
• 제17권2호
• /
• pp.20-25
• /
• 1989

This study was carried out in order to investigate the treatment effect of PEG soln which is a common dimensional stabilizer to green log. sawing panel etc, on bonding product including plywood widely-used in secondary processing unit. The 30% concentration of aqueous PEG soln. with molecular weight of 400, 1.000 and 4,000 were prepared respectively, and also dipping the veneer in the PEG soln. spreading the PEG soln. on veneer and mixing the PEG soln. in the adhesive were allowed. Then the ratio of PEG impregnation on veneer, the adhesive strength of plywood were epitomized as follows: The ratio of impregnation by PEG 4,000 at dipping condition was highest. while that by PEG 400 at same condition was lowest. However, the effect of PEG molecular weight on the ratio of impregnation at spreading condition did not occur. 2. The adhesive strength was great in the order of 4,000>400>1,000 in molecular weight of PEG at dipping and spreading conditions. In case of mixing the PEG soln. in the adhesive, the adhesive strength was great in the order of 400>1,000>4,000 in molecular weight of PEG. Throughout three treatment conditions, PEG 400 was relatively favourable with about 10kg/$cm^2$ dry strength. 3. The adhesive strength was great 10 the order of spreading >dipping >mixing condition. 4. Although adhesive strength with the 30% concentration of aqueous PEG soln. was decreased by 35% and over, compared to control (non-treatment) adhesive strength, all types of PEG treatment except mixing the PEG soln. in the adhesive exceeded the standard dry strength for common use panel. 7.5kg/$cm^2$. 5. In warm water-proof test, the adhesive strengths by all PEG treatment conditions were less than the standard wet strength, 7.5kg cot, and also delamination of glue line occured mostly in mixing in the PEG soln. in the adhesive condition.

• 대한전자공학회논문지TC
• /
• 제47권11호
• /
• pp.14-18
• /
• 2010

M-ary와 PN 확산의 조합이 존재하는 CDMA 시스템에서 성능분석 방법을 제안하였다. M-ary와 PN 확산에 의한 전체 대역폭 확장이 같더라도 두 블럭의 대역폭 확장의 조합에 따라 시스템 성능이 달라진다. 따라서 M-ary와 PN 확산이 이루는 CDMA 시스템 전체 대역폭 확장이 아니라, 각각의 대역폭 확장을 사용하여 시스템 성능을 분석하였다. 그리고 SINR이 높을수록 M-ary에 의한 대역폭 확장이 PN 확산에 의한 대역폭 확장보다 비트오율을 더 많이 감소시키는 것을 볼 수 있었다. 제안한 성능분석 방법이 M-ary에 의한 성능개선의 효과를 반영했기 때문에 전체 대역폭 확장만을 사용한 방법보다 더 정확한 성능분석을 할 수 있었다.

• 한국전산유체공학회지
• /
• 제21권4호
• /
• pp.90-95
• /
• 2016

Leidenfrost drops with ellipsoidal shaping can control the bouncing height by adjusting the aspect ratio(AR) of the shape at the moment of impact. In this work, we focus on the effect of the AR and the impact Weber number(We) on the non-axisymmetrical spreading dynamics of the drop, which plays an important role in the control of bouncing. To understand the impact dynamics, the numerical simulation is conducted for the ellipsoidal drop impact upon the perfect non-wetting solid surface by using volume of fluid method, which shows the characteristics of the spreading behavior in each principal axis. As the AR increases, the drop has a high degree of the alignment into one principal axis, which leads to the consequent suppression of bouncing height with shape oscillation. As the We increases, the maximum spreading diameters in the principal axes both increase whereas the contact time on the solid surface rarely depends on the impact velocity at the same AR. The comprehensive understanding of the ellipsoidal drop impact upon non-wetting surface will provide the way to control of drop deposition in applications, such as surface cleaning and spray cooling.