• Journal of Korean Society of Occupational and Environmental Hygiene
• /
• v.29 no.4
• /
• pp.541-549
• /
• 2019

Objectives: This study aims to examine patients who developed acute pesticide poisoning while spraying or using pesticide and presented to the emergency department in hospitals in Chungcheongnam-do Province. Based on the findings, this study will provide implications for safety and health management pertaining to the use of pesticides. Methods: Pesticide poisoning data collected by the Chungnam Center for Farmers' Safety and Health from 2014 to 2018 was cross-sectionally analyzed. A total of 331 patients with pesticide poisoning presented to one of hospitals and four of medical centers in the region(Dankuk University Hospital, Gongju and Hongsung, Cheongyang, Cheonan Medical Center). Seventeen of these patients (15 men and two women) developed poisoning while spraying pesticide. The patients' charts were reviewed to collect data on pesticide poisoning, namely currently working in farming-related occupation, means of transportation to the hospital, place of poisoning, symptoms of acute pesticide poisoning, treatment, pesticide used when poisoning occurred, and classification by technical ingredients. Results: Fifteen out of 17 patients who developed poisoning while spraying pesticide were men. Insecticide was used in 35.3% of the cases, and herbicide was used in 29.4% of the cases, which was different from cases of poisoning from ingestion poisoning. The major symptoms were vomiting (35.3%), nausea (29.4%), dizziness (29.4%), and headache (23.5%). A total 11 ingredients were identified in 12 patients, and the most common ingredient was glyphosate, which is an herbicide. Most patients showed a state of mild toxicity, but two patients showed a state of severe toxicity. These patients respectively used glyphosate and paraquat. Conclusions: Our findings can be useful for suggesting the need for a national healthcare system to manage occupational pesticide poisoning among farmers. Further, these findings can be used to increase the awareness of the risk of acute poisoning during pesticide spraying and suggest the need for a safety health education to increase farmers' awareness of pesticide poisoning.

• Journal of Biosystems Engineering
• /
• v.35 no.3
• /
• pp.163-168
• /
• 2010

With income growth and "well-being" trends, sales of corn has been increased recently. Corns are processed at processing facilities on the main production site. Corn processing steps include removing bract, steaming, vacuum packing, and storing. To replace manual corn bract removing, some bract removing machines were imported and used. However, the machines were abandoned shortly, because of high damaging ratio of corns. In this research, factors of successful bract removing was studied with rotating rollers and air-injection nozzles to develop corn bract removing system. The test device was composed of a cylindrical roller, an air spray nozzle, a regulator, and a motor. Designing factors were roller type, diameter of air spraying nozzle, spraying angle, and spraying pressure. The measured factors were bract removing rate and damaging rate. It was found that optimum cylindrical roller surface shape was cylindrical roller and linear grove roller. This roller shape produced lowest damaging rate. Test results of the efficacy of preprocessing showed that the air spraying after preprocessing produced highest performance. The rotational speed and inclination of the roller didn't affect the bract removing performance. Optimum injection angle of the air jet nozzle was $70^{\circ}$. To increase bract removing rate and to reduce corn damage, required injection pressure and injection nozzle diameter were decided to less than 0.4 MPa and 2.5 mm, respectively. More than 3 times of nozzle passing produced good bract removing performance and there were no significant difference between the number of passing times.

• Korean Journal of Medicinal Crop Science
• /
• v.28 no.6
• /
• pp.435-444
• /
• 2020

Background: As the Positive List System (PLS) is implemented in broad application to agricultural products, attention to the correct use of pesticides is also needed in the production of mulberry leaves and fruit. In this regard, three types of pesticides against mulberry popcorn disease were applied 2 - 3 times both in the field and greenhouses to prepare safety standards. Residual pesticide analysis was conducted on mulberry fruits and leaves. Methods and results: Three pesticieds, thiophanate-methyl, thiophanate-methyl·triflumizole and fluopyram registered as PLS pesticides for mulberry popcorn disease, were sprayed in the Wanju and in Buan regions, after which residual pesticide analysis was conducted using high-performance liquid chromatography (HPLC). As three pesticieds were either undetected or below the permissible level in mulberry fruit, demonstrating that they were suitable for safe spraying. However, 5.6 mg/kg of thiophanate-methyl was detected in the greenhouse after three application, which was slightly above maximum residue limit (MRL). Furthermore the level of thiophanate-methyl·triflumizole was higher than 0.2 mg/kg ("Gwasang No. 2" variety, spraying twice) or similar to 0.09 mg/kg ("Daesim" variety, spraying thrice) the permissible level (0.1T mg/kg) as the thiophanate-methyl was detected in mulberry leaves in the greenhouse. Conclusions: The spraying frequency for controlling mulberry popcorn disease in greenhouses should be limited to two times or less, especially when mulberry leaves are treated with thiophanate-methyl·triflumizole careful consideration is required if the leaves are to be used as food materials.

• Journal of Biosystems Engineering
• /
• v.35 no.5
• /
• pp.302-309
• /
• 2010

Aerial application using an unmanned agricultural helicopter would allow precise and timely spraying. The attitude of a helicopter depends on a number of dynamic variables for roll-balanced flight. Laterally tilting behavior of a helicopter is a physically intrinsic phenomenon while hovering and forwarding. In order to balance the fuselage, the rotor should be counter-tilted, resulting in the biased down-wash. The biased spraying toward right side causes uneven spray pattern. In this study, a raised tail rotor system for the roll-balanced helicopter was studied. Thrust of the tail rotor system was measured and theoretically estimated for the fundamental database of the roll-balanced helicopter design. The estimated tail thrust and roll-moment would be used to design the raising height of tail rotor and roll balancing dynamics. The unmanned agricultural helicopter required the tail rotor thrust of about 39.2 N (4.0 kgf) during hovering with a payload of 235.4 N (24 kgf). A raised tail rotor system would compensate for the physical tilt phenomena. A further attitude control system of helicopter would assist roll-balanced aerial spray application.

• Journal of Welding and Joining
• /
• v.15 no.1
• /
• pp.116-124
• /
• 1997

A scope of this study is to establish the optimum plasma spray conditions for fine ($5\mu\textrm{m}$) $Al_2O_3$ powder. However, the flowability of the $Al_2O_3$ powder is not so good because of irregular particle shape and fine particle size. Therefore, powder feeding system was modified by 1) change of powder feeding line material from polymer to copper 2) shorten the powder feeding tube length 3) heating the powder feeding system to $80^{\circ}C$4) vibrating the powder feeding line continuously, in order to feed the fine powder homogeneously. The homogeneous powder feeding conditions were obtained with the modified powder feeding system by controlling the powder carrier gas flow and the powder flow rate indicator. The best plasma spraying conditions for the fine $Al_2O_3$ powder were found out as 40kw gun power, 80 g/min. powder feed rate and 50 mm working distance after characterizing the microstructure, hardness and wear loss of the $Al_2O_3$ coating layer.

• Journal of Biosystems Engineering
• /
• v.31 no.3 s.116
• /
• pp.182-187
• /
• 2006

Aerial application using an unmanned agricultural helicopter can reduce labor and pollution. The development of an agricultural helicopter became urgent for both precise and timely spraying. In this study, a rotor system for unmanned helicopter capable of 20 $kg_f$ payload, was developed and lift capability was evaluated. A lift force over the dead weight of the helicopter was obtained at the pitch angle of $6^{\circ}$. As the pitch angle increased to $8^{\circ}\;and\;10^{\circ}$, the total lift increased to $74{\sim}81\;kg_f\;and\;86{\sim}93\;kg_f$, respectively. A range of engine speed at the rated flight condition, lifting mean payload of 23 $kg_f$ was determined. The data acquired from this study will be used for designing tail system and RF console in the next stage of the research. The rated lift capability was enough for loading 20 liters of spray material including spraying equipments.

• Journal of Korean Society of Water and Wastewater
• /
• v.30 no.6
• /
• pp.725-736
• /
• 2016

There is a growing concern on the improvement of water distribution pipeline for multi-regional water supply system in Korea along with its aging infrastructure. Rehabilitation of large diameter pipeline is more efficient in cost and time compared to replacement with trenching. The procedure for rehabilitation are diagnosis, cleaning, spraying coating material, and final inspection. The internal state of pipeline was carefully diagnosed and got C grade, which required rehabilitation. We found that 17,274,787,000 Korean won could be saved after pipe surface coating because of increased C coefficient of Hazen-Williams equation. Optimal coating material was D polyurea. We also found optimal distance between spraying nozzle and pipe wall to be 70 - 80 cm, which were critical factors for coating quality. This study also illustrated the time for spray drying to be more than 30 min. These results could be used in the quality control process during rehabilitation of aged pipelines.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.4
• /
• pp.100-105
• /
• 2016

The use of 3D scanners has increased gradually according to increasing 3D printer applications. The precision inspection of car parts or electronic components is an important issue not only in the field of mass production, but also in small-scale production. Recently, 3D scanner equipment efficiency and recognition technology has been improved continuously. On the other hand, the spraying time to prepare 3D scanning is time-consuming and has environmental problems. Therefore, an automatic spray system has been in demand by the manufacturing industry. Automatic spray equipment was newly developed for the preparation of a 3D scanner. In this research, the automatic spray system guarantees uniform spray operation. To determine the optimal spray parameters, various spraying methods, solutions and conditions were tested and compared with the experiments. The preparation time for 3D scanning was reduced to 1/10 compared to the manual spraying time, and indicates the optimal spraying conditions through a comparison of various spray coating conditions.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09a
• /
• pp.156-157
• /
• 2006

The preparation of composite powders for plasma spraying by an in-house designed mechanofusion process is investigated. Results show that dry particle coating depends on the chemical and mechanical properties of powders. In metal/oxide and metal/oxide/carbide powder mixtures, fine ceramic particles coat the surface of the metallic coarser particles. A nearly rounded shape of the final composite particles is induced by the mechanical energy input with no formation of new phases. However with the carbide/metal powdered system, only an intimate mixture of components is achieved. It is suggested that the coating mechanism is governed by agglomeration and rolling phenomena.

• Journal of the Korean Society of Safety
• /
• v.33 no.6
• /
• pp.8-14
• /
• 2018

Recently, serious problems occurred such as insecticide eggs, sanitary pads with carcinogens, radon(Rn) emitting beds in domestic. It had not been establishing the inspection system to evaluate safety and human harmfulness before occurring real accidents. This research was conducted to test preliminary experimental inspection for consideration of safety insensibility. The influence of corrosion of metals and plants was studied through aerosol type spraying of agricultural pesticide products coming into the market. These products contain primary three insecticide ingredients(Flufenoxuron, Etoxazole, Fipronil) in recent accidents. Visual examination, SEM-EDS and optical microscope were used for the analysis for corrosion effect. Results show that a lot of ingredients contain in the crop protection products, and various type of corrosion exist in the surface of metals and plants. Therefore, it is necessary to provide health warning and accurate range of use for crop protection products containing insecticide ingredients.