• Journal of ILASS-Korea
• /
• v.8 no.1
• /
• pp.29-36
• /
• 2003

Spray characteristics on diesel- water emulsion are analyzed in high pressure injection for several variables such as water content, injection pressure. Spray Patterns were visualized under various water content and injection pressures. Spray tip penetration was increased and spray angle decreased in accordance with increasing of water content. But these characteristics were enhanced with increase of injection pressure to high pressure.

• Journal of ILASS-Korea
• /
• v.10 no.4
• /
• pp.47-53
• /
• 2005

This paper presents the effects of ambient pressure on atomization characteristics of high-Pressure injector in a direct injection gasoline engine both experimentally and numerically. The atomization characteristics such as mean droplet size, mean velocity, and velocity distribution were measured by phase Doppler particle analyzer. The spray development, spray penetration, and global spray structure were visualized using a shadowgraph technique. In order to investigate the atomization process numerically, the LISA-DDB hybrid model was utilized. This breakup model assumes that the primary breakup occurs when the amplitude of the unstable waves is equal to the radius of the ligament of liquid sheet near the nozzle and the droplet deformation induces the secondary breakup. The results provide the effect of ambient pressure on the macroscopic and microscopic behaviors such as spray development, spray penetration, mean droplet size, and mean velocity distribution. It is also revealed that the accuracy of prediction of LISA-DDB hybrid model is pretty good in terms of spray developing process, spray tip penetration, and SMD distribution.

• Journal of Mechanical Science and Technology
• /
• v.19 no.11
• /
• pp.2040-2052
• /
• 2005

The present paper centers on the establishment of a quantified relationship between the macroscopic visual parameters of a Diesel spray and its most influential factors. The factors considered are the ambient gas density, as an external condition relative to the injection system, and nozzle hole diameter and injection pressure as internal ones. The main purpose of this work is to validate and extend the different correlations available in the literature to the present state of the Diesel engine, i.e. high injection pressure, small nozzle holes, severe cavitating conditions, etc. Five mono-orifice, axi-symmetrical nozzles with different diameters have been studied in two different test rigs from which one can reproduce solely the real engine in-cylinder air density, and the other, both the density and the pressure. A parametric study was carried out and it enabled the spray tip penetration to be expressed as a function of nozzle hole diameter, injection pressure and environment gas density. The temporal synchronization of the penetration and injection rate data revealed a possible explanation for the discontinuity observed as well by other authors in the spray's penetration law. The experimental results obtained from both test rigs have shown good agreement with the theoretical analysis. There have been observed small but consistent differences between the two test rigs regarding the spray penetration and cone angle, and thus an analysis of the possible causes for these differences has also been included.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.13 no.3
• /
• pp.131-137
• /
• 2005

Ultra high pressure injection equipment was developed to estimate and analyze the spray characteristics in ultra high pressure injection. Spray patterns were visualized by schlieren method and analyzed in ultra high pressure. Spray tip penetration, spray thickness, spray volume, and entrained air mass increased with the increase of the injection pressure. But over 2,800 bars of the injection pressure region, it was shown that the rate of improvement was not increased remarkably ,and the spray characteristics such as spray penetration, volume, and entrained air mass were reversed and got worse at 4,140 bars.

• International Journal of Automotive Technology
• /
• v.7 no.4
• /
• pp.493-500
• /
• 2006

Investigation on the fuel adhering on a wall was carried out experimentally to clarify the characteristics of impinging diesel sprays. Diesel sprays were injected into a high-pressure chamber of cold state and impinged to a wall having various impingement distances and ambient pressures. Photographs of both the fuel film and the post-impingement spray were taken through a transparent wall. Adhered fuel mass on a wall was measured by means of dividing into two types of fuel state: the fuel film itself; and sparsely adhered fuel droplets. Adhering fuel ratio was predicted and further the distribution of fuel mass for impinging diesel spray was analyzed as a function of time. As result, with an increase of the ambient pressure, both the maximum fuel film diameter and the adhered fuel ratio decreased. Based on some assumptions, the adhering fuel mass increased rapidly until the fuel film diameter approached the maximum value, and then increased comparatively gradually.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.15 no.3
• /
• pp.47-53
• /
• 2007

To suppress the bubble generated in the liquid LPG direct injector is the most important to develop the LPDi engine. It was found in the previous study that bubbling phenomenon in the injector of the LPDi engine is decisively influenced by pressure of fuel and temperature around the injector. Therefore, in this study, the effect on suppressing the bubbling in the LPDi injector by high pressurization of fuel is analyzed and the spray characteristics are also studied. As a result, it is found that the bubbling in the LPDi injector is radically suppressed when the pressure of fuel is over 50MPa. The bubbling is suppressed when the pressure of fuel is over 3MPa if the inserted position of the injector is considered. Also, it is confirmed that the higher the pressure of fuel is the longer spray tip penetration and is the larger spray angle. As the ambient pressure increases, spray tip penetration decreases and spray angle increases due to the increase of drag force.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2003.06a
• /
• pp.764-767
• /
• 2003

The characteristics of diesel spray have much effect on the engine performances such as power. fuel consumption rate and emissions. Therefore, the measurement of fuel spray characteristics is very important for the improvement of heat engine. The factors which control diesel spray characteristics are injection pressure, ambient temperature and density etc. Spray behaviors are visualized by using the high speed video camera and spray angle, spray penetration are measured. Experimental equations of spray penetration and spray angle were derived by using the experimental results. 1) Ambient temperature and density influence on the characteristics of diesel spray. 2) Experimental equation of spray penetration is expressed as follows 0＜t＜ $t_{b}$ ; $S_1$=11.628$\Delta$ $P^{0.485}$ $\rho$$_{a}$ $^{-0.478}$ $t^{1.337}$, $t_{b}$ ＜t; $S_2$=7.457$\Delta$ $P^{0.523}$ $\rho$$_{a}$ $^{-0.382}$ $t^{0.548}$ 3) Experimental equation of spray Angie is expressed as follows $T_{a}$ =293K; Tan($\theta$/2)=059($\rho$$_{a}$ / $\rho$$_{f}$ )$^{0.437}$, $T_{a}$ =473K; Tan($\theta$/2)=0588($\rho$$_{a}$ / $\rho$$_{f}$ )$^{0.404}$_{f}$ )$^{0.404}$

• Transactions of the Korean Society of Automotive Engineers
• /
• v.15 no.5
• /
• pp.30-37
• /
• 2007

Dimethyl Ether(DME) is an alternative fuel for diesel engine, it is renewable and offers potential reductions in emissions. This work was conducted to figure out the macroscopic behavior and the atomization characteristics of DME using a common-rail injection system. The macroscopic behavior was visualized with the spray visualization system composed of a Nd;YAG laser and an ICCD camera. The atomization characteristics were investigated in terms of axial mean velocity, Sauter mean diameter(SMD) and droplet distributions obtained from a phase Doppler particle analyzer(PDPA) system. In this study, it was revealed that the macroscopic behavior and the atomization characteristics of DME are similar compared with commercial diesel fuel. However, DME fuel has a shorter spray tip penetration and a small SMD due to the effect of evaporation characteristics.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.10 no.6
• /
• pp.27-33
• /
• 2002

This paper presents the comparison of prediction accuracy of hybrid models. To obtain the experimental results fur comparing with the numerical results, the macroscopic and microscopic structures of the hollow-cone spray such as spray development process, spray penetration and the distribution of mean droplet size are investigated by using a shadowgraph technique and phase Doppler particle analyzer. Also, the numerical researches using various hybrid models are performed. LISA model and WAVE model are used for the primary breakup, and TAB, DDB, and RT model are used for the secondary breakup.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.8 no.3
• /
• pp.28-36
• /
• 2000

Spray characteristics of diesel fuel injection is one of the most important factors in diesel combustion and pollutant emissions especially in HSDI (High Speed Direct Injection) diesel engines where the interval between the onset of combustion and the evaporation of atomized fuel is relatively short, An investigation into various spray characteristics from different holes of VCO(Valve Covered Orifice) nozzles was performed and its results were compared to standard sac nozzle. The global characteristics of spray, including spray angle, spray tip penetration, and spray pattern were measured from the spray images which were frozen by an instantaneous photography with a spark light source. For better understanding of spray behavior, SMD of the fuel sprays from multi hole nozzles were measured with back light imaging while the sprays from the other holes are covered by a purpose-built nozzle cap. The investigation manifestly reveals the different spray patterns at the beginning of injection produced by VCO nozzles can be identified as three distinct types with their own macroscopic and microscopic characteristics, while macroscopic non-uniformity disappears at 0.9∼1.0ms from the start of injection.