• Proceedings of the KIPE Conference
• /
• 2004.07a
• /
• pp.303-307
• /
• 2004

This paper presents a new speed control scheme of the spindle induction motor (IM) using fuzzy-logic control in field weakening region. The implementation of the proposed FLC-based spindle IM are investigated and compared to those obtained from the conventional PI controller based drive system, we have confirmed good simulation and experimental results at different dynamic operating conditions such as sudden change in command speed, step change, etc.

• Journal of the Korean Society for Precision Engineering
• /
• v.27 no.12
• /
• pp.119-124
• /
• 2010

In this paper, thermal stabilization design of a new concept compact machining center has been investigated. A new concept machining center adopted a new X-axis as a NC rotary table. A New concept compact machining center is designed that spindle speed, feed rate and NC Rotary table speed are 12,000rpm, 60m/min and 110rpm each. The analysis is carried out by using FEM simulation Solidworks, CATIA and ANSYS. This paper is focused on the thermal deformation according to temperature distribution of a spindle system and feed drive system. Heat transfer analysis is performed according to heat source and atmosphere contact parts. As a result, this compact machining center is designed as a thermally stable structure.

• Journal of KSNVE
• /
• v.10 no.6
• /
• pp.977-984
• /
• 2000

Vibration of disk drive spindle is one of the major limiting factors in achieving higher track densities in hard disk drives. Vibration of a BLDC motor is a coupled phenomenon between mechanical characteristics and magnetic origins through the motor air-gap. In this paper, radial magnetic forces for symmetric and asymmetric BLDC motor are calculated with respect to the various rotor eccentricity using analytic method. Based on the results of the radial magnetic forces, transient whirl responses of the spindle motor are analyzed using finite element and transfer matrices. Results show that an asymmetric motor has a worse effects on unbalanced magnetic forces and vibration when mechanical and magnetic coupling exists.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2003.05a
• /
• pp.571-577
• /
• 2003

This research proposes a finite element method to determine the natural vibration characteristics of the spinning disk-spindle system in a HDD including the flexibility of supporting structure. Finite element equations of each substructure are derived with the introduction of consistent variables to satisfy the geometric compatibility at the internal boundaries. The natural frequencies and modes from the global asymmetric matrix equations of motion are determined by using the implicit restarted Arnoldi iteration method. The validity of the proposed method is verified by the experimental modal testing. It also shows that the flexibility of base plate plays an important role to determine the natural frequencies of the spinning disk-spindle system in a HDD.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.49 no.11
• /
• pp.742-748
• /
• 2000

This paper presents a numerical method to analyze the electromechanical-coupled field in the spindle motor of a computer hard drive and investigates dynamic response due to the electromechanical excitation, i.e. unbalanced magnetic force and centrifugal force for the rotational asymmetric motor. Magnetic field is calculated from Maxwells equation and voltage equation by introducing nonlinear time-dependent finite element analysis. Mechanical motion of rotor is calculated by solving Newton-Euler equation. Electromechanical excitation and dynamic response are characterized by analyzing the free response of a rotating rotor and Fourier analysis of the excitation force and resulting vibration of a rotor. It shows that centrifugal force produces the unbalanced magnetic force even in the rotational symmetric motor. It also shows that resonance produces quite considerable vibration even when the high excitation frequency with small amplitude matches with the natural frequency of the spindle motor.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 1997.10a
• /
• pp.29-35
• /
• 1997

This research presented a frequency analysis method to analyze NRRO in a computer hard disk drive. RRO was proved to be the harmonics of rotational frequency. The frequency components of NRRO is the subtraction of the harmonics from TIR in frequency domain, so that NRRO in time domain can be obtained by Fourier inverse transformation of NRRO in frequency domain. This method can make the experiments simple without the index signal indispensable to time domain analysis. This research also shows that NRRO is caused by the defect frequencies of ball bearing. Even though the excitation force of ball bearing is independent of the rotational speed, the amplitude of NRRO is magnified near the resonance frequencies of the spindle motor. NRRO in axial direction is almost twice bigger than that in radial direction, because the spindle motor has smaller stiffness in axial direction.

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.60 no.2
• /
• pp.82-90
• /
• 2011

The small precision spindle motors in the high value-added products including the visible home appliances such as DLP projector require not only the energy conversion devices but also high efficiency, low vibration and sound operation. However, the spindle motors using the conventional ball bearing and sintered porous metal bearing have following problems, respectively: the vibration by the irregularity of balls and the short motor life cycle by the ball's abrasion and higher sound noises by dry contact between shaft and sleeve. In this paper, it is proposed that the spindle motor with a fluid dynamic bearing is suitable for the motor to drive the color wheel of the DLP(digital lightening processor) in the visible home appliances. The proposed spindle motor is composed of the fluid dynamic bearing with both the radial force and the thrust force. The fluid dynamic bearing is solved by the finite element analysis of the mechanical field with the Reynolds equations. The magnetic part of spindle motor, which is a type of Brushless DC Motor, is designed by the electro-magnetic field analysis coupled with the Maxwell equation. And the load capacity and the friction loss of fluid dynamic bearing are analyzed to bearing clearance variation by the fabrication error in designed motor. The design of the proposed motor is implemented by the load torque caused by the eccentricity and the unbalance of the fluid dynamic bearing when the motors are fabricated in error. The prototype of the motor with the fluid dynamic bearing is manufactured, and experiment results show the vibration, sound, and phase current at no load and color wheel load of the motors in comparison. The high performance characteristics with the low vibration, the low acoustic noise and the optimal mechanical structure are verified by the experimental results.

• Journal of the Korean Society of Safety
• /
• v.18 no.1
• /
• pp.44-49
• /
• 2003

Permanent magnet synchronous motor(PMSM) is widely used in many applications such as an electric vehicle. compressor drives of air conditioner and machine tool spindle drives. PMSM drive system have become a popular choice in various application, due to their excellent power to weight ratio. This paper is proposed maximum torque control for field weakening operation of PMSM drive. At low speeds, the reluctance torque is used to maximize the output for a given current level. This is achieved maximum torque per ampere(MTPA) by selecting an optimal value of the direct stator current component. At high speeds, the system reaches a point at which the inverter will not be able to supply the desired voltage. In this case it is necessary to make use of an increased value the direct current component. The proposed control algorithm is applied to PMSM drive system, the operating characteristics controlled by maximum torque control are examined in detail by simulation.

• Proceedings of the KIEE Conference
• /
• 2001.07b
• /
• pp.1179-1181
• /
• 2001

For high performance induction motor drives such as mill drives, elevator, spindle drive, NC and so on, smart speed controls is usually required, that requires a precise current control. This paper is proposes design of fuzzy controller which makes use of the output voltage of the space vector PWM inverter. Also, proposes the performance fuzzy controller for high performance vector control of induction motor drive system. The performance of a fuzzy controller is compared with that of an PI controller in an internal loop. The validity of the proposed technique is confirmed by simulation results for induction motor drive system.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1997.10a
• /
• pp.580-584
• /
• 1997

As the optical disk drive is getting applied to wider ranges, higher density of media and higher velocity of spindle motor are demanded and therefore its design criterion is becoming more strict. Especially, the vibration problem is one of the most important factors to be considered for reliable performance. In this study, the possibility of the application of the vibration absorber using rubber mount was investigated by 3 dimensional modeling and analysis by Recurdyn program. The model chosen was a vibration absorber using rubber mount installed on the sled base of the optical disk drive.