• Journal of Institute of Control, Robotics and Systems
• /
• v.21 no.9
• /
• pp.881-887
• /
• 2015

The hardware-in-the-loop simulation (HILS) of a railway vehicle is crucial for overcoming the limitation of field tests of a railway vehicle. A brake HILS system for a railway vehicle was previously not able to test the performance of a speed-sensing system of a railway vehicle, since wheelset speeds were generated only by computer simulations. In this paper, we present a novel wheelset speed implementation of a brake HILS system for a railway vehicle. Four wheelset speeds of a brake HILS system for a car of a railway vehicle are implemented using four small-sized servomotors, whereas the speed sensors and pole wheels used in the brake HILS system are the actual ones of the railway vehicle. According to the simulated speeds of four wheelsets in the dynamic equations of motion, four servomotors generate wheel speeds in real time, and then the measured wheelset speeds are fed back to the computer simulation model. Moreover, in this paper, we improve the performance of wheelset speed measurement via the T method instead of the M method presently used in the field. The performances of wheelset speed implementation and speed-sensor operation are demonstrated by experimental works using a HILS system.

• International Journal of Automotive Technology
• /
• v.3 no.4
• /
• pp.171-176
• /
• 2002

A bench test set-up is employed to simulate the friction characteristics of a paper-based friction material operating against a steel plate. Dry friction tests are run as well as tests with transmission fluids. Glazed friction material produces a negative coefficient of friction versus sliding velocity (f-v) curve for both dry friction and lubrication with transmission fluids. At low sliding speeds, the coefficient of friction when operating in transmission fluids for glazed friction materials is greater than that under dry friction. An appreciable negative f-v slope occurs at low sliding speeds for glazed friction materials when running with the transmission fluid. The friction material after running in produces a constant f-v curve under dry friction and a negative slope when lubricated with transmission fluid. At low sliding speeds, the coefficient of friction of the run-in friction material is lower than that of the glazed wet material. On the other hand, the run-in friction material has a larger friction coefficient than does the glazed friction material at higher sliding speeds.

• Journal of Korean Society of Transportation
• /
• v.12 no.1
• /
• pp.137-149
• /
• 1994

The objective of study is to evaluate the effect of speed control hump on traffic operation and accidents. Three sites were investigated for the change of traffic accidents before and after the hump installation. Vehicle speeds approaching the hump were also analyzed. The study revealed that not only the number of traffic accidents but also the accident severity were significantly reduced by the installation of hump. Further, different types of traffic accidents with lower severity were observed after the hump installation. For the effect of speed reduction by hump, it was found that the speeds observed at 15m upstream of hump were in the range of 36~50 percent of approaching speeds which were not affected by (ie, without) the hump. Economic analysis of hump installation showed the benefit-cost ratio of 4.3 and 11.2 at two sites. Further analysis revealed that the benefit by the accident reduction exceeds the cost by speed reduction and installation capital if AADT is below 43,150 vehicles on two lane highways. It is recommended from the study that humps should be considered on two lane highways of high accident locations for excessive speeds to reduce traffic accidents and severity.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.14 no.1
• /
• pp.50-55
• /
• 2004

In this study, slit-tones by plane impinging jet are investigated experimentally over the whole subsonic flow range, especially at low speeds, in order to obtain the instability behaviour of impinging plane jet. Slit-tones are generated at low speeds associated with laminar shear layer instability as well as at high speeds associated with turbulent instability. Most of low-speed slit-tones are induced by symmetric mode instability unless the slit is not so wide, in which case antisymmetric modes are induced like edge-tones. It is found that the frequencies at low speeds ate controled by the unstable condition of the vortex at the nozzle exit and its pairings by which the frequencies are decreased by half. In the case of symmetric modes related with low-speed slit-tones, frequencies lower than those associated with one-step pairings are not found.

• Journal of the Korean Society of Combustion
• /
• v.17 no.2
• /
• pp.9-16
• /
• 2012

Iso-octane, n-heptane and their blends were tested in a constant volume combustion chamber to measure laminar flame speeds. The experimental apparatus was automatically controlled to enhance the accuracy and data acquisition speed. A large database of laminar flame speeds at elevated temperatures and pressures was established. From this database, laminar flame speeds of iso-octane, n-heptane and their blends were investigated and analysed to derive new correlation to predict laminar flame speeds at any blending ratio. The new flame speed model was successfully applied to these fuels with limited range of errors.

• Journal of Korean Society of Industrial and Systems Engineering
• /
• v.35 no.1
• /
• pp.140-147
• /
• 2012

Vehicle routing problem is one of the traveling salesman problems with various conditions such as vehicle capacity limits, delivery time windows, as well as time dependent speeds in metropolitan area. In this research hourly vehicle moving speeds information in a typical metropolitan area are analyzed to use the results in the design procedure of VRP heuristic. Quality initial vehicle routing solutions can be obtained with adaption of the analysed results of the time periods with no vehicle speed changes. This strategy makes complicated time dependent vehicle speed simple to solve. Time dependent vehicle speeds are too important to ignore to obtain optimum vehicle routing search for real life logistics systems.

• Journal of Power Electronics
• /
• v.10 no.1
• /
• pp.72-78
• /
• 2010

In this paper the operation of a double-fed wound-rotor induction machine, coupled to a wind turbine, as a generator at sub-synchronous speeds is investigated. A novel approach is used in the analysis, namely, the rotor power flow approach. The conditions necessary for operating the machine as a double-fed induction generator (DFIG) are deduced. Formulae describing the factors affecting the range of sub-synchronous speeds within which generation occurs are deduced. The variations in the magnitude and phase angle of the voltage injected to the rotor circuit as the speed of the machine changes to achieve generation at the widest possible sub-synchronous speed range is presented. Also, the effect of the rotor parameters on the generation range is presented. The analysis proved that the generation range could increase from sub-synchronous to super-synchronous speeds, which increases the amount of energy captured by the wind energy conversion system (WECS) as result of utilizing the power available in the wind at low wind speeds.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 1988.10a
• /
• pp.7-12
• /
• 1988

This study presents rational methods for probability-based estimates of basic design wind speeds in Korea and develops a risk-bases nation-wide map of design wind speeds. The paper examines the fitting of the Type-I extreme model to maximum yearly non-typhoon wind data from long-term records based on the conventional method and to maximum monthly nod-typhoon wind data from short-term records following Grigorin's approach. The paper also reviews the applicability of the method using short records of about 5 years. The basic design wind speeds for typhoon and non-typhoon wind at a station are made to be obtained from a mixed model which is given as a product of typhoon and non-typhoon extreme wind distributions. A practical method which is based on the fitting of the Type I model to records or typhoon and non-typhoon mixed wind data at a station is also preposed in this study.

• International Journal of Highway Engineering
• /
• v.14 no.5
• /
• pp.113-122
• /
• 2012

PURPOSES: The sensitivity of $CO_2$ emissions per vehicle by a various speeds is compared according to the type of roads. METHODS: The methodology of the study are as follows: First, the sensitivity of $CO_2$ emissions per vehicle are analyzed by averaged daily travel speeds. Second, the sensitivity of $CO_2$ emissions per vehicle are analyzed by averaged hourly travel speed. Third, the sensitivity of $CO_2$ emissions per vehicle are analyzed by sectional travel speeds. RESULTS: The sensitivity that on Saturday in a week, at peak times in a day and in close location from Seoul was higher than in other situations. CONCLUSIONS: From this study, we may conclude that $CO_2$ emissions per vehicle at low speeds are generally more sensitive.

• IE interfaces
• /
• v.11 no.1
• /
• pp.75-84
• /
• 1998

The important issue for intra-city vehicle scheduling is to measure and store actual vehicle travel speeds between customer locations. Travel speeds(and times) in nearly all metropolitan areas change drastically during the day because of congestion in certain parts of the city road network. We propose three models for estimating departure time-dependent travel speeds between locations that relieve much burden for the data collection and computer storage requirements. Two of the three models use a least squares method and the rest one employs a neural network trained with the back-propagation rule. On a real-world study using the travel speed data collected in Seoul, we found out that the neural network model is more accurate than the other two models.