• 한국ITS학회 논문지
• /
• 제16권3호
• /
• pp.59-72
• /
• 2017

기존 실시간 신호제어시스템의 루프검지기 기반 수집체계의 한계를 극복하기 위해 실시간 택시 GPS 데이터를 신호제어에 활용할 수 있는 방안에 대한 연구의 일환으로, 본 논문은 2016년 발표한 링크평균통행시간과 대기차량길이의 추정 모형과 교통상황 판단 알고리즘에 대해 평과와 개선을 수행하였다. 링크평균통행시간은 연동그룹과 비연동그룹을 고려하여 평균통행시간을 고도화하였고, 대기차량길이는 교통상황을 고려하여 추정모형을 고도화 하였다. 링크평균통행시간의 정확도는 약 95%, 대기차량길이의 정확도는 약 85%로 분석되었다. 교통상황판단 알고리즘은 정확도가 향상된 통행속도와 대기차량길이를 반영하였다. 반영된 지표들의 변동을 줄이고 교통상황의 추세를 판단하기 위해 평활화를 수행하였으며, 과포화 상황 판단 기준에 통과주기를 반영하여 알고리즘을 고도화하였다.

• Elastomers and Composites
• /
• 제45권1호
• /
• pp.40-43
• /
• 2010

본 연구에서는 전기방사 장치의 드럼형태 컬렉터의 회전속도를 조절함으로써 제조된 섬유가 랜덤 또는 배향성 (1축, 2축)을 갖는 폴리이미드(PI) 나노섬유 매트를 제조하였다. 제조된 PI 매트의 구조를 전자현미경(SEM)을 통해 관찰한 결과 전술한 배향성을 확인할 수 있었다. 1 M 리튬트리풀루오로-메탄-설포네이트와 테트라-에틸렌 글리콜디메틸 에테르의 혼합용액에 PI 매트를 침지시킨 후 이온전도기로 이온전도도를 측정하였다. 2축배향 매트가 가장 높은 이온전도도를 나타내었다. 1축 배향의 경우 이온의 이동방향과 수직방향이 평행방향보다 이온전도도가 낮게 나타났고, 아울러 일정한 주기성을 나타내었다. 주기성은 섬유간 거리와 이온 속도를 이용하여 설명할 수 있었다.

• Journal of Electrical Engineering and Technology
• /
• 제9권3호
• /
• pp.1096-1103
• /
• 2014

This paper proposes a novel strategy for attenuating the output power fluctuation of the wind farm (WF) in a range of tens of seconds delivered to the grid, where the kinetic energy caused by the large inertia of the wind turbine systems is utilized. A control scheme of the two-level structure is applied to control the wind farm, which consists of a supervisory control of the wind farm and individual wind turbine controls. The supervisory control generates the output power reference of the wind farm, which is filtered out from the available power extracted from the wind by a low-pass filter (LPF). A lead-lag compensator is used for compensating for the phase delay of the output power reference compared with the available power. By this control strategy, when the reference power is lower than the maximum available power, some of individual wind turbines are operated in the storing mode of the kinetic energy by increasing the turbine speeds. Then, these individual wind turbines release the kinetic power by reducing the turbine speed, when the power command is higher than the available power. In addition, the pitch angle control systems of the wind turbines are also employed to limit the turbine speed not higher than the limitation value during the storing mode of kinetic energy. For coordinating the de-rated operation of the WT and the storing or releasing modes of the kinetic energy, the output power fluctuations are reduced by about 20%. The PSCAD/EMTDC simulations have been carried out for a 10-MW wind farm equipped with the permanent-magnet synchronous generator (PMSG) to verify the validity of the proposed method.

• 한국가시화정보학회:학술대회논문집
• /
• 한국가시화정보학회 2006년도 추계학술대회 논문집
• /
• pp.17-20
• /
• 2006

Passenger safety is fundamental factor in automobile. Among much equipment for passenger safety, the air bag system is the most fundamental and effective device. Beside of the front air bag system which installed on most of all automobiles, a curtain-type air bag is increasingly adapted in deluxe cars fur protecting passengers from the danger of side clash. Curtain type airbag system consists of inflator housing, fill hose, curtain airbag. Inflator housing is a main part of the curtain-type air bag system for supplying high-pressure gases to deploy the air bag-curtain. Fill hose is a passageway to carry the gases from inflator housing to each part of curtain airbag. Therefore, it is very important to design the vent holes of fill hose for good performance of airbag deployment. But, the flow information from vent holes of fill hose is very limited. In this study, we measured instantaneous velocity fields of a high-speed flow ejecting from the vent holes of fill hose using a dynamic PIV system. From the velocity Held data measured at a high frame-rate, we evaluated the variation of the mass flow rate with time. From the instantaneous velocity fields of flow ejecting from the vent holes in the initial stage, we can see a flow pattern of wavy motion and fluctuation. The flow ejecting from the vent holes was found to have very high velocity fluctuations and the maximum velocity was about 480m/s at 4-vent hole region. From the mass flow rate with time, the accumulated flow of 4-vent hole has occupied about 70% of total flow rate.

• Journal of Radiation Protection and Research
• /
• 제44권1호
• /
• pp.32-42
• /
• 2019

Background: There have been much efforts to develop the proper and realistic machine Quality Assurance (QA) reflecting on real Volumetric Modulated Arc Therapy (VMAT) plan. In this work we propose and test a special VMAT plan of plan-class specific (pcsr) QA, as a machine QA so that it might be a good solution to supplement weak point of present machine QA to make it more realistic for VMAT treatment. Materials and Methods: We divided human body into 5 treatment sites: brain, head and neck, chest, abdomen, and pelvis. One plan for each treatment site was selected from real VMAT cases and contours were mapped into the computational human phantom where the same plan as real VMAT plan was created and called plan-class specific reference (pcsr) QA plan. We delivered this pcsr QA plan on a daily basis over the full research period and tracked how much MLC movement and dosimetric error occurred in regular delivery. Several real patients under treatments were also tracked to test the usefulness of pcsr QA through comparisons between them. We used dynalog file viewer (DFV) and Dynalog file to analyze position and speed of individual MLC leaf. The gamma pass rate from portal dosimetry for different gamma criteria was analyzed to evaluate analyze dosimetric accuracy. Results and Discussion: The maxRMS of MLC position error for all plans were all within the tolerance limit of < 0.35 cm and the positional variation of maxPEs for both pcsr and real plans were observed very stable over the research session. Daily variations of maxRMS of MLC speed error and gamma pass rate for real VMAT plans were observed very comparable to those in their pcsr plans in good acceptable fluctuation. Conclusion: We believe that the newly proposed pcsr QA would be useful and helpful to predict the mid-term quality of real VMAT treatment delivery.

• 대기
• /
• 제33권4호
• /
• pp.343-354
• /
• 2023

Turbulence produced on roadways is one of the major factors determining the dilution rates at the initial stage of traffic emissions of air pollutants and, thus, the distribution of air pollutants near the roadways. Field experiments were conducted on Gyeongbu Highway, one of the busiest highways in Korea, for 4~7 days in winter, spring, and summer. Two three-dimensional ultrasonic anemometers were installed on both sides of the highway to estimate turbulence intensities (vertical wind fluctuation and kinetic turbulence energy) induced by the roadway. Roadway-induced turbulence consists of three components: structural road-induced turbulence (S-RIT), thermal road-induced turbulence (T-RIT), and vehicle-induced turbulence (VIT). The contribution of T-RIT to the total RIT was insignificant (less than 10%), and the majority of RIT was S-RIT (by the highway embankment) and VIT. In this study, we propose the empirical relationships of VIT as a function of traffic density and wind speed under free-flow traffic conditions. Although this empirical relationship appears to underestimate the VIT, it can be applied to the air quality models easily because the relationship is simple and only needs readily obtainable input variables (wind speed and traffic information).

• 한국축산시설환경학회지
• /
• 제16권3호
• /
• pp.193-204
• /
• 2010

본 연구는 국내 여건에 적합한 돈사시설과 분뇨처리가 일체형으로 조합된 고상식 돈사에 적합한 환기시스템을 찾고자 수행하였다. 덕트입기${\rightarrow}$ 측벽배기 (처리 V1), 처마입기 (측벽천장)${\rightarrow}$측벽배기 (처리 V2), 천장입기${\rightarrow}$측벽배기 (처리 V3) 3종류의 환기시스템을 설치하였다. 시험 시기는 겨울철과, 여름철부터 가을철에 실시하였다. 환기시스템별 고상식 돈사내 온도, 공기유속, 암모니아, 황화수소, 돼지성장 등을 조사하였다. 그 결과는 다음과 같다. 겨울철 동안 온도는 덕트입기에서 온도가 약간 높은 경향을 보였으며, 외기온도에 영향을 받지 않았다. 여름철부터 가을철 동안 최고온도는 $33.4{\sim}33.8^{\circ}C$ 처리간에 큰 차이를 보이지 않았으며,외기온도에 영향을 받는 것으로 나타났다. 가을철 일일 연속적 온도 변화에서 처마입기가 다른 환기시스템보다 낮은 온도를 유지와 온도의 편차가 큰 것으로 나타났다. 겨울철 동안 돈사내 공기유속은 덕트입기와 처마입기는 0.02~.21 m/s 로 비슷한 경향이었으며 천장입기는 0.04~.15 m/s 이었다. 여름철부터 가을철동안 돈사내 공기유속은 덕트입기 0.10~.41 m/sec 처마입기 0.10~83m/sec 천장입기 0.11~.26 m/sec의 공기유속을 보였다. 가을철 일일 연속적 공기유속변화에서 처마입기가 공기유속의 변화가 다른 환기시스템보다 큰 것으로 나타났다. 겨울철 동안 돈사내 $NH_3$ 발생 최고 농도는 덕트입기 7.0 ppm, 마입기 3.5 ppm,천장 입기 8.7 ppm 검출 되었으며,$H_2S$는 검출되지 않았다. 여름철부터 가을철 동안 돈사내 $NH_3$ 발생 최고농도는 덕트입기 6.1 ppm, 처마입기 2.8 ppm, 천장입기 5.6 ppm 검출되었다. 돼지 성장에서 환기시스템 간 통계적인 유의성은 없었으나, 겨울철 동안 일당증체량은 덕트입기와 천장입기가 처마입기보다 약 4% 높은 증체를 보였으며, 사료섭취량/증체량은 덕트입기에서 사육되는 돼지가 효율이 약 4% 높은 것으로 나타났다. 여름철부터 가을철 동안 덕트입기와 천장입기에서 사육되는 돼지의 일당증체량이 처마입기에서보다 약 3% 정도 높은 경향을 보였으며, 사료섭취량/증체량은 덕트입기에서 사육되는 돼지가 효율이 약 2% 높은 것으로 나타났다. 이상의 결과를 종합하여 볼 때 고상식 돈사용 환기시스템으로 처마입기 (측벽천장) 측벽배기 적용은 비효율적이라 판단된다.

• International Journal of Naval Architecture and Ocean Engineering
• /
• 제6권2호
• /
• pp.257-268
• /
• 2014

In this study, flow-driven rotor simulations with a given load are conducted to analyze the operational characteristics of a vertical-axis Darrieus turbine, specifically its self-starting capability and fluctuations in its torque as well as the RPM. These characteristics are typically observed in experiments, though they cannot be acquired in simulations with a given tip speed ratio (TSR). First, it is shown that a flow-driven rotor simulation with a two-dimensional (2D) turbine model obtains power coefficients with curves similar to those obtained in a simulation with a given TSR. 3D flow-driven rotor simulations with an optimal geometry then show that a helical-bladed turbine has the following prominent advantages over a straight-bladed turbine of the same size: an improvement of its self-starting capabilities and reduced fluctuations in its torque and RPM curves as well as an increase in its power coefficient from 33% to 42%. Therefore, it is clear that a flow-driven rotor simulation provides more information for the design of a Darrieus turbine than a simulation with a given TSR before experiments.

• 대한기계학회논문집 C: 기술과 교육
• /
• 제3권2호
• /
• pp.89-96
• /
• 2015

Based on multi-body dynamic software RecurDyn, this paper proposes a modified form of timing silent chain system combing with the existing problem that vibration and chain tension is too large, which is applied for complicated conditions in a V-type engine, such as high speed, variable loads. The analysis of chain drive meshing characteristics is completed. Using the multi-body dynamic soft-ware RecurDyn, the dynamics characteristics of the improved system is studied, including chain tension, transmission error, chain fluctuations, equivalent spring force in different operating conditions. The study results show that chain tension, transmission error, chain fluctuation and equivalent spring force are within the scope of permission, all of them can meet the design requirement. There-fore, the design of this system is reasonable and practicable. The research results will provide a basis for assessing timing silent chain system in a V-type engine and a theoretical reference for designing and optimizing the timing silent chain system.

• 수산경영론집
• /
• 제14권1호
• /
• pp.44-56
• /
• 1983

This study is attempted to serve the fundamental theory for ‘The reorganization of Korean coastal and adjacent water fishery.’ On the Korean coastal and adjacent water fishery where one species stock is catched by multiple fisheries, traditional analysis is not suitable, as analyzing through adjusting the heterogeneous fishing effort among the fisheries to an unit having same fishing strength. Therefore, this study presents the ‘Multi-Variable Model’, adopting fishing effort from each fishery as independent variable, respectively, in order to analyze the quantitative fluctuation of fishery resource not with fishing strength but with amount of fishing effort, measured by the unit of each fishery. For the sake of simplication, this study assumes that one species is catched by two fishery, premise two assumption. 1) Every fishery has not the selectivity in fishing 2) The promotion of fishing efficiency is accomplished in the same speed. Resource equilibrium equation of each fishery is; $$CPUE_1=\frac{Y_1}{E_1}=a_1+ b_1\cdot E_1+c_1\cdot E_1$$ $$CPUE_1=\frac{Y_1}{E_1}=a_1+ b_1\cdot E_1+c_1\cdot E_1$$ Sustainable yield equation is; $$SY_1=a_1\cdot E_1+\cdot b_1E{_1}{^2}+c_1\cdot E_1\cdot E_1$$ $$SY_1=a_1\cdot E_1+b_1\cdot E_1\cdot E_1+c_1\cdot E{_1}{^2}$$ This study is rudimentary, hereafter, refinemental analysis will be supplemented.