• 한국생산제조학회지
• /
• 제24권1호
• /
• pp.110-116
• /
• 2015

This study investigates the whirling stability of a rotating shaft-disk system under parametric excitation using periodically varying torque. The equations of motion were derived using a lumped-mass model, and the Floquet method was employed to find the effects of torque fluctuation, internal and external damping, and rotational speed on whirling stability. Results indicated that the effect of torque fluctuation was considerable on the instability around resonance, but minimal on supercritical instability. Stability diagrams were sensitive to the parametric excitation frequency; critical torque decreased upon increasing excitation frequency, with faster response convergence or divergence. In addition, internal and external damping had a considerable effect on unstable regions, and reduced the effects of the parametric excitation frequency on critical torque and speed. Results obtained from the Floquet approach were in good agreement with those obtained by numerical integration, except for some cases with Floquet multipliers very close to unity.

• 한국자동차공학회논문집
• /
• 제4권5호
• /
• pp.90-99
• /
• 1996

To keep up with the regulation of OBD II(on board diagnostics II), many detection methods for engine misfire have been developed. Among them, the method of using the crankshaft speed fluctuation is the most noticeable in the point of view of lower cost and easier installation than any others. On the basis of the results obtained from the previous engine-dynamometer test, the integrating torque index (ITI) has been introduced. In this research, the instrumental and the interfacing systems to engine control unit(ECU) are developed for the vehicle test. Therefore, the vehicle and chassis-dynamometer test can be carried out in addition to the rough road test. From this test, the previousproposed method proved that it can be applied to the real vehicle.

• 전기학회논문지
• /
• 제67권6호
• /
• pp.695-701
• /
• 2018

For a power grid that has a high wind penetration level, when wind speeds are continuously fluctuating, the maximum power point tracking (MPPT) operation of a variable-speed wind turbine (VSWT) causes the significant output power fluctuation of a VSWT, thereby significantly fluctuating the system frequency. In this paper, an improved power-smoothing scheme of a VSWT is presented that significantly mitigates the frequency fluctuation caused by varying wind speeds. The proposed scheme employs an additional control loop based on the frequency deviation that operates in combination with the MPPT control loop. To improve the power-smoothing capability of a VSWT in the over-frequency section (OFS), the control gain of the additional loop, which is set to be inversely proportional to the rotor speed, is proposed. In contrast, the control gain in the under-frequency section is set to be proportional to the rotor speed to improve the power-smoothing capability while avoiding over-deceleration of the rotor speed of a VSWT. The proposed scheme significantly improves the performance of the power-smoothing capability in the OFS, thereby smoothing the frequency fluctuation. The results clearly demonstrate that the proposed scheme significantly mitigates the frequency fluctuation by employing the different control gain for the OFS under various wind penetration scenarios.

• Journal of Mechanical Science and Technology
• /
• 제20권4호
• /
• pp.482-493
• /
• 2006

The carbody structure of a high speed train passing through a tunnel is subjected to pressure fluctuation. Fatigue strength of the carbody structure against the fluctuating pressure loading should be proved in the design stage for safety. In this study, to get the useful information on the pressure fluctuation in the tunnel, measurement has been conducted during test running of KHST on the high speed line for two years. The measured results were analyzed and arranged to be used for carbody design. A prediction method for the magnitude and frequency of pressure change was proposed and the propagating characteristics of pressure wave was investigated. By statistical analysis for the measured results, a pressure loading spectrum for the high speed train was given. The proposed method can also be used to estimate the pressure loading spectrum for new high speed line at design stage combined with the results of train performance simulation.

• Journal of Electrical Engineering and Technology
• /
• 제9권6호
• /
• pp.2134-2141
• /
• 2014

This paper addresses on a wind power system with BESS(Battery Energy Storage System). The concerned system consists of four parts: the wind speed production model, the wind turbine model, configure capacity of the battery energy storage, battery model and control of the BESS. First of all, we produce wind speed by 4-component composite wind speed model. Secondly, the maximum available wind power is determined by analyzing the produced wind speed and the characteristic curve of wind power. Thirdly, we configure capacity of the BESS according to wind speed and characteristic curve of wind speed-power. Then, we propose a control strategy to track the power reference. Finally, some simulations have been demonstrated to visualize the feasibility of the proposed methodology.

• 드라이브 ㆍ 컨트롤
• /
• 제17권2호
• /
• pp.28-37
• /
• 2020

It is difficult to analytically derive the relationship among volumetric displacement, flowrate, torque, and rotation speed regarding an instantaneous position of gerotor hydraulic pumps/motors. This can be explained by the geometric shape of the rotors, which is highly complicated. Herein, an analytical method for the instantaneous torque, rotation speed, flowrate, and volumetric displacement of a pump/motor is proposed. The method is based on two physical concepts: energy conservation and torque equilibrium. The instantaneous torque of a pump/motor shaft is determined for the posture of rotors from the torque equilibrium. If the torque equilibrium is combined with the energy conservation between the hydraulic energy of the pump/motor and the mechanical input/output energy, the formula for determining the instantaneous volumetric displacement and flowrate is derived. The numerical values of the instantaneous volumetric displacement, torque, rotation speed, and flowrate are calculated via the MATLAB software programs, and they are illustrated for the case in which inner and outer rotors rotate with respect to fixed axes. The degrees of torque fluctuation, speed fluctuation, and flowrate fluctuation can be observed from their instantaneous values. The proposed formula may provide a better understanding of the design or analysis process of gerotor pumps/motors.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2011년도 정기총회 및 추계학술대회 논문집
• /
• pp.3037-3045
• /
• 2011

The optimization of the overhead contact lines according to the increased train speed is to design the low-sag-wire so that the pantograph can follow the vertical fluctuation of the catenary. Main factors for the overhead contact lines design include the span, dropper interval, movable bracket, vertical fluctuation of the catenary, tension, and wave propagation speed. In this paper, a model is proposed to improve the electric railway speed, and the speed improvement analysis technology is examined to ensure the stable and reliable electric railway. In addition, the effect between pantograph and catenary according to the speed improvement is quantitatively analyzed by using simulation.

• 대한전자공학회논문지SD
• /
• 제43권6호
• /
• pp.53-61
• /
• 2006

고속 Flash, Pipelining type의 CMOS A/D 변환기에서 Sampling frequency가 고주파로 올라감에 따라 Clock Feed-through 현상, Kick-back 현상 등의 영향으로 DC Reference voltage 흔들림 현상이 심화되고 있다. 뿐만 아니라 측정 시 외부 Noise가 Reference voltage에 적지 않은 영향을 미친다는 것을 감안 할 때 High speed A/D converter에서 Reference fluctuation 감쇄회로는 반드시 필요하다. 기존의 방식은 단순히 커패시터를 이용했으나 면적이 크고 효과가 좋지 않다는 단점이 있다. 본 논문에서는 Transmission Gate를 이용한 reference fluctuation 감쇄 회로를 제안하고 흔들림 현상이 크게 개선되었음을 정량적 분석 및 측정을 통하여 증명하였다. 제안하는 회로의 측정을 위해 6bit의 해상도를 갖는 2GSPS CMOS A/D 변환기를 설계 및 제작하였다. 제작된 A/D 변환기를 이용하여 Reference 전압이 40mV의 흔들림이 있음에도 원하는 범위 내에서 동작함을 측정하였다. 본 연구에서는 1.8V $0.18{\mu}m$ 1-poly 5-metal N-well CMOS 공정을 사용하였고, 소비전력은 145mW로 Full Flash 변환기에 비해 낮았다. 실제 제작된 칩의 SNDR은 약 36.25dB로 측정되었고, INL과 DNL은 각각 ${\pm}0.5$ LSB 이하로 나타났다. 유효칩 면적은 $997um\times1040um$ 이었다.

• 한국기계가공학회지
• /
• 제2권1호
• /
• pp.85-91
• /
• 2003

The experimental study for turning circular free fanned surface with TiN coated insert tool was conducted for different cutting conditions such as cutting speed, feed rate and depth-of-cut. For the fluctuation of 1.0mm depth-of-cut, the characteristics for machined surface and tool wear were less influenced by the feed rate and cutting speed than those of higher depth of cut. The higher surface roughness and surface precision were obtained in lower cutting speed. For the fluctuation of 1.5mm depth-of-cut, the higher surface roughness was obtained for the case of the lower feed rate of 0.05-10mm/rev and the higher cutting speed of 80m/min. For the fluctuation of 2.0mm depth-of-cut, the surface roughness and surface precision were too worse to machine the specimen And the flank wear on the tool was increased rapidly rather than the crater wear.

• International Journal of Fluid Machinery and Systems
• /
• 제2권1호
• /
• pp.92-101
• /
• 2009

The purpose of this paper is to gain a greater understanding of the performance of practical wind turbine generating systems with differing output power controllers and controlling means for wind turbine speed. Subjected wind turbines, both equipped with an asynchronous power generator, are located at two sites and are defined as wind turbine A and wind turbine B in this study, respectively. Their performance differences are examined by measuring wind speed and electric parameters. The study suggests that both wind turbines have a clear linkage between current and output power fluctuations. Comparison of the fluctuations to wind speed fluctuation, although they are triggered primarily by wind speed fluctuation, clearly indicates the specific behaviors inherent to the respective turbine control mechanisms.