• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2014년도 추계학술대회 논문집
• /
• pp.443-448
• /
• 2014

Recently, car-ferry passenger ships of navigating the coast area in the inside of our country are on an increasing trend of main engine power and the height of upper structure, which is increased to ship's speed and loading of large vehicles. The most ship with high-speed main engine is happened to excessive vibration by propeller induced excitation force on account of connecting the vibration of hull's girder and the upper structure by decreasing the shear stiffness and natural frequency for increasing the height of passenger deck. In this paper, By exchanging the propeller of alteration the number of blades, it could be keep to ship's speed and it's decreased the vibration of hull part that is located passenger deck on the upper deck, which is identified by countermeasure of protection against vibration to procure the safety ship's navigation through measuring the vibration of hull structure.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2009년도 춘계학술대회 논문집
• /
• pp.529-538
• /
• 2009

A trial run of locally-developed tilting train has been in process on Chungbuk line since the test vehicle was first produced. For the system stabilization, interface verification among the systems including track, structure, catenary and signaling system, not to mention the rolling stock, is very crucial. Therefore, in this study, the dynamic rail force of the tilting (Hanvit 200), high-speed (KTX) and general (Mugunghwa) vehicle caused by driving in transition curve track was measured. And, it compared the tilting response with the other by using the measured wheel load data in transition curve track, and then evaluated probability the range of wheel load fluctuation for the variable dynamic vertical and lateral wheel load. As a result, a range of wheel load by occured a change of cant from the high-speed and general vehicle which had fixed bogie structure was distributed throughout small deviation (${\Delta}8{\sim}13kN$). Otherwise, in case of the tilting train which was consisted of the pendulum bogie structure was distributed wide range about large deviation (${\Delta}25{\sim}28kN$) by changed of cant.

• 드라이브 ㆍ 컨트롤
• /
• 제11권3호
• /
• pp.31-40
• /
• 2014

This paper proposes a multi absorbing wave energy converter design, in which a hydrostatic transmission is used to transfer wave energy to electric energy. The most important feature of this system is its combination of the pressure coupling principle with the use of a hydraulic accumulator to eliminate the effects of wave power fluctuation; this maintains a constant speed of the hydraulic motor. Tilt motion of a floating buoy was employed as the power take-off mechanism. Furthermore, a PID controller was designed to carry out the speed control of the hydraulic motor. The design offers some advantages such as extending the life of the hydraulic components, increasing the amount of energy harvested, and stabilizing the output speed.

• 대한조선학회지
• /
• 제27권3호
• /
• pp.1-10
• /
• 1990

본 논문에서는 얇은 배 이론, Hess & Smith방법, 유사실적자료 및 모형실험결과를 이용하여 고속콘테이너선의 선형을 개발한 연구결과가 소개도어 있다. 양력면이론에 의해 설계된 고효율 프로펠러는 캐비테이션과 변동압력에서 좋은 성능을 보였으며, 유한요소법에 근거한 최적설계기법으로 선체구조설계와 선체진동해석을 수행하였다. 끝으로, 새로이 개발된 본 고속콘테이너선의 성능을 실선 시운전결과와 비교, 검토하였으며, 이로부터 속력, 진동 및 기타성능에 있어서의 우월성이 확인되었다.

• Wind and Structures
• /
• 제32권2호
• /
• pp.89-104
• /
• 2021

Non-synoptic winds generated by tornadoes, downbursts or gust fronts exhibit significant non-stationarity and can cause significant wind load effect on flexible structures such as long-span bridges. However, conventional assumptions on stationarity used to evaluate the structural wind-induced vibration are inadequate. In this paper, an efficient frequency domain scheme based on fast CQC method, which can predict non-stationary buffeting random responses of long-span bridges, is presented, and then this approach is applied to evaluate the buffeting response of a long-span suspension bridge located in a complex mountainous wind environment as an example. In this study, the data-driven method based on one available measured wind speed sample is firstly presented to establish non-stationary wind models, including time-varying mean wind speed, time-varying intensity envelope function and uniformly modulated fluctuating spectrum. Then, a linear time-variant (LTV) system based on the proposed scheme can be generally applied to calculate the non-stationary buffeting responses. The effectiveness and accuracy of the proposed scheme are verified through Monte Carlo time domain simulation implemented in ANSYS platform. Also, the transient effect nature of the bridge responses is further illustrated by comparison of the non-stationary, quasistationary and steady-state cases. Finally, buffeting response analysis with traditional stationary treatment (10 min constant mean plus stationary wind fluctuation) is performed to illustrate the importance of the non-stationary characteristics embedded in original wind speed samples.

• 한국전기전자재료학회논문지
• /
• 제25권2호
• /
• pp.85-90
• /
• 2012

In this paper, we compared and analyzed 3D silicon-oxide-nitride-oxide-silicon (SONOS) multi layer flash memory devices fabricated on nitride or oxide layer, respectively. The device fabricated on nitride layer has inferior electrical properties than that fabricated on oxide layer. However, the device on nitride layer has faster program / erase speed (P/E speed) than that on the oxide layer, although having inferior electrical performance. Afterwards, to find out the reason why the device on nitride has faster P/E speed, 1/f noise analysis of both devices is investigated. From gate bias dependance, both devices follow the mobility fluctuation model which results from the lattice scattering and defects in the channel layer. In addition, the device on nitride with better memory characteristics has higher normalized drain current noise power spectral density ($S_{ID}/I^2_D$>), which means that it has more traps and defects in the channel layer. The apparent hooge's noise parameter (${\alpha}_{app}$) to represent the grain boundary trap density and the height of grain boundary potential barrier is considered. The device on nitride has higher ${\alpha}_{app}$ values, which can be explained due to more grain boundary traps. Therefore, the reason why the devices on nitride and oxide have a different P/E speed can be explained due to the trapping/de-trapping of free carriers into more grain boundary trap sites in channel layer.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2007년도 추계학술대회 논문집
• /
• pp.1370-1378
• /
• 2007

고속철도 교량은 고속주행 열차의 차축 주기하중 효과와 교량 고유의 동적특성에 의한 동적 증폭 효과로 인하여 구조물의 안전성에 영향을 받는다. 그리고 교량의 과도한 변형으로 인하여 차륜과 레일의 접촉력 감소, 궤도틀림 등의 윤중 변동이 일어나 열차의 주행안전성 및 승차감을 저해할 수 있다. 이러한 궤도 안전성을 확보하기 위하여 동적거동에 대한 교량상판수준의 수직가속도 제한, 차륜-레일간의 접촉과 열차주행 안전성 확보를 위한 상판 면틀림 제한, 단부 회전각 변위 제한, 차량하중에 의한 교량의 수직 처짐 제한을 반드시 만족시켜야 하며, 필수적으로 공진에 대한 검토도 이루어져야 한다. 신설되는 호남고속철도에서는 기존의 경부고속철도와 다른 콘크리트 도상을 적용하고, 궤도간격, 설계열차하중 등이 변경되어 적용되므로 새로운 동적안정성 요구조건을 적용하게 된다. 본 연구에서는 콘크리트교량에 비해 진동특성이 취약한 것으로 알려진 강합성 거더 고속철도 교량의 동적거동 분석을 수행하였다.

• 전자공학회논문지
• /
• 제49권9호
• /
• pp.251-258
• /
• 2012

SSD (Solid-state Drive), 더 나아가 SSS (Solid-state Storage System)와 같은 고성능 스토리지 요구 사항을 지원하기 위해 최근 낸드 플래시 메모리도 DRAM에서와 같이 SDR (Single Data Rate)에서 고속 DDR (Double Data Rate) 신호구조로 진화하고 있다. 이에 따라 PHY (Physical layer) 회로 기술을 적용하여 협소 타이밍 윈도우 내에서 유효 데이터를 안정적으로 래치하고, 핀 간 데이터 스큐를 최소화하는 것 등이 새로운 이슈로 부각되고 있다. 또한, 낸드 플래시 동작 속도의 증가는 낸드 플래시 컨트롤러의 동작 주파수 상승으로 이어지고 동작 모드에 따라 컨트롤러 내부 소모 전력 변동성이 급격히 증가한다. 공정 미세화와 저전력 요구에 의해 컨트롤러 내부 동작 전압이 1.5V 이하로 낮아지면서 낸드 플래시 컨트롤러 내부 전압 변화 마진폭도 좁아지므로 이러한 소모 전력 변동성 증가는 내부 회로의 정상 동작 범위를 제한한다. 컨트롤러의 전원전압 변동성은 미세공정으로 인한 OCV (On Chip Variation)의 영향이 증가함에 따라 더 심화되는 추세이고, 이러한 변동성의 증가는 순간적으로 컨트롤러의 보장된 정상 동작 범위를 벗어나게 되어 내부 로직의 오류를 초래한다. 이런 불량은 기능적 오류에 의한 것이 아니므로 문제의 원인 규명 및 해결이 매우 어렵게 된다. 본 논문에서는 낸드플래시 컨트롤러 내부의 비정상적 전원 전압 변동하에서도 유효 타이밍 윈도우를 경제적인 방법으로 유지할 수 있는 회로 구조를 제안하였다. 실험 결과 기존 PHY회로 대비 면적은 20% 감소한 반면 최대 데이터 스큐를 379% 감소시켜 동등한 효과를 보였다.

• 한국철도학회논문집
• /
• 제8권4호
• /
• pp.348-353
• /
• 2005

In designing the structures of railway rolling stocks, deterministic methods associated with the concept of a safety factor have been traditionally used. The deterministic approaches based on the mean values of applied loads and material properties have been used as safety verification for the design of rolling-stock car body structures. The uncertainties in the applied loading for the high speed train and the strength of new materials in the rolling stocks require the application of probabilistic approaches to ensure fatigue safety in the desired system. Pressure loadings acting on the car body when the train passes through tunnels show reflected pressure waves for high-speed trains and they may cause a fatigue failure in vehicle bodies. Use of new material technology as body structures also introduces uncertainties in the material strength. A probabilistic approach is more adaptable in designing reliable structures when the pressure waves from the tunnels pounds and new material technology is adopted. In this paper, it is proposed that a fatigue design and assessment method based on a reliability which deals with the loading variations on a railway vehicle due to the pressure reflected in tunnels and the strength variations of material. Equation for the fatigue reliability index has been formulated to calculate the reliability assessment of a vehicle body under fluctuating pressure loadings in a tunnel. Considered in this formulation are the pressure distribution characteristics, the fatigue strength distribution characteristics, and the concept of stress-transfer functions due to the pressure loading.

• 한국자동차공학회논문집
• /
• 제15권2호
• /
• pp.115-125
• /
• 2007

Minimizing the cylinder wear and the consumption rate of cylinder oil in a large two-stroke marine diesel engine is of great economic importance. In Korea, a motor-driven cylinder lubricator for a large two-stroke marine diesel engine manufactured by $W{\ddot{a}}rtsil{\ddot{a}}$ Switzerland Co., Ltd. was first developed by authors through the joint research of industry-university in 2002. The characteristic of the developed product is that can control automatically the oil feed rate to a load fluctuation by the motor drive and the offset cam. The performance of the product is not also inferior to the conventional one. For manufacturing the reliable and useful products, however, it is necessary to investigate further characteristics and improve the performance of a cylinder lubricator. In this study, the effect of quill with and without accumulator on maximum discharge pressure, delivery delay duration and oil feed rate relative to motor revolution speed using plunger stroke as a parameter is experimentally investigated by using the developed cylinder lubricator. It is found that the maximum discharge pressure with accumulator is higher than that of no accumulator as plunger stroke and motor revolution speed are elevated, and the delivery delay duration with accumulator is shorter than that of no accumulator as plunger stroke and motor revolution speed are increased. Also, oil feed rate with accumulator is less than that of no accumulator except for a plunger stroke of 2 mm as plunger stroke and motor revolution speed are raised.