• 한국자동차공학회논문집
• /
• 제6권4호
• /
• pp.39-46
• /
• 1998

For permanent magnet brushless DC motors used for high speed fuel pumps, torque ripple is an important origin of vibration, acoustic noise and speed fluctuation. In this paper, the output torque profile of a PM motor with one phase energized is decomposed into the commutation torque, the reluctance torque and the armature reaction torque according to their source origins. It verifies that the output torque profile is qualitatively equivalent to the BEMF profile for low reluctance motors. This paper discusses the effect of magnet pole shaping and magnet arc length on the output torque and torque ripple. A magnet edge shaping is proposed to design a trapezoidal BEMF motor without torque ripple, with minimal sacrifice of the maximum output torque.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1997년도 하계학술대회 논문집 B
• /
• pp.696-698
• /
• 1997

The marine diesel engine have been widely applied with a mechanical hydraulic governor to control the ship speed for long time. But it was recently very difficult for the mechanical hydraulic governor to control the speed of engine under the condition of low speed and low load because of jiggling by rough fluctuation of rotating torque and hunting by dead time of diesel engine. In order to analyze the speed control system the transfer function was converted from z to w transformation. The author proposed velocity control system with feedback loop by PID controller in order to stabilize for unstable area. The influence of dead time was discussed by Nichols chart and unit step response curve. It was confirmed through computer simulation that the performance improvement of a mechanical hydraulic governor can be obtained by PID controller.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2002년도 춘계합동학술대회 논문집
• /
• pp.73-76
• /
• 2002

The switched reluctance motor(SRM) drive system provides a good adjustable speed and torque characteristics. However, because of the torque production mechanism, it also has some disadvantage such as higher torque ripple and fluctuation in speed. To reduce torque ripple and to control speed precisely, digital signal processor(DSP) is adopted. The DSP TMS320F241 is used to be realized this drive system. Test results show that the suggested control system has the ability of dynamic and precise speed control.

• Journal of Advanced Marine Engineering and Technology
• /
• 제20권3호
• /
• pp.137-143
• /
• 1996

The propulsion marine diesel engine has been widely applied with a mechanical-hydraulic governor to control the ship speed for long time. But it was recently very difficult for the mechanical-hydraullic governor to control the speed of engine under the condition of low speed and low load because of jiggling and hunting by rough fluctuation of rotating torque. To solve these problems of control systems, the performance improvement of mechanical-hydraulic governor is required. In this paper, in order to analyze the speed stability of control systems, the influence of parameters of the engine dead time, gain, damping ratio was discussed on the view of control engineering. The performance improvement of a conventional mechanical hydraulic governor is confirmed to be possible by fuzzy control scheme.

• 국제초고층학회논문집
• /
• 제8권4호
• /
• pp.313-324
• /
• 2019

This paper presents the analysis of wind speeds data measured on top of three neighboring high-rise buildings close to a beach in Xiamen city, China, during Typhoon "Usagi" 2013. Wind tunnel simulation was carried out to validate the field measurement results. Turbulence intensity, turbulence integral scale, power spectrum and cross correlation of recorded wind speed were studied in details. The low frequency trend component of the typhoon speed was also discussed. The field measurement results show turbulence intensity has strong dependence to the wind speed, upwind terrain and even the relative location to the Typhoon center. The low frequency fluctuation could severely affect the characteristics of wind. Cross correlation of the measured wind speeds on different buildings also showed some dependence on the upwind terrain roughness. After typhoon made landfall, the spatial correlation of wind speeds became weak with the coherence attenuating quickly in frequency domain.

• 한국자동차공학회논문집
• /
• 제10권3호
• /
• pp.44-50
• /
• 2002

The connecting rod big-end bearing is one of the most heavily loaded components of the lubrication system of high-speed combustion engines. The supply oil flow has to pass to the main bearing and the rotating crankshaft before entering the connecting rod bearing. It is common knowledge that the centrifugal forces due to the crankshaft rotation influence the oil flow to connecting rod bearing through the oil supply bore, especially, when the oil supply system to the connecting rod bearing has a 180$^{\circ}$circumferential groove via a single drilling in the crankshaft. In this case, it should be confirmed that the groove oil pressure in the main bearing is sufficient to overcome these centrifugal forces. For the purpose, the dynamic oil pressure before entering oil supply bore to the connecting rod bearing was measured instead of averaged oil pressure in main gallery. Experimental test results show that the dynamic oil pressure in the oil groove was more useful than that of main gallery. And it was also found that the oil pressure fluctuation in the groove was sensitively affected by the reduction of the main bearing clearance.

• 한국자동차공학회논문집
• /
• 제6권3호
• /
• pp.88-96
• /
• 1998

The rattle noise is the most significant in many kinds of manual gearbox nioses, which is generated at the idle stage of the engine operation. The main torsional vibrat- ion source of the driveline is the fluctuation of the engine torque. The gear rattle is impacts generating in the backlash of the free gear due to this torsional vibration. Many researchers reported the clutch torsional characteristic optimization method to reduce the idle gear rattle but only few of them give sufficient consideration to the system parameters like gear backlash, drag torque, system inertia, inertia distribution, engine torque fluctuation, idle engine rotation speed, and accessory load. In this paper, influence rate of system parameters on the gear rattle is presented and counterplans like backlash reduction, drag torque increase, inertia addition, inertia distribution modification and engine torque characteristic control are suggested.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 1997년도 추계학술대회 논문집
• /
• pp.292-297
• /
• 1997

The rattle noise is the most significant in many kinds of manual gearbox noises, which is generated at the idle stage of the engine operation. The main torsional vibration source of the driveline is the fluctuation of the engine torque. The gear rattle is impacts generating in the backlash of the free gear due to this torsional vibration. Many researchers reported the clutch torsional characteristic optimization method to reduce the idle gear rattle but only few of them give sufficient consideration to the system parameters like gear backlash, drag torque, system inertia, inertia distribution, engine torque fluctuation, idle engine rotation speed, and accessory load. This paper pays attention to the gear impact mechanism and system design parameters to reduce the idle gear rattle with computer simulation.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2008년도 춘계학술대회 논문집
• /
• pp.303-306
• /
• 2008

The wind power generation systems have a fluctuating or intermittent power output due to the variability of the wind speed. The amount of wind generation which can be connected to the grid without causing voltage stability problems is limited. In this study, the simulation of the wind power generation including energy storage system were performed to reduce the fluctuation of wind power output and to obtain the optimal operation planning of energy storage system.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 1998년도 연구회 합동 학술발표회 논문집
• /
• pp.33-37
• /
• 1998

For the high power variable speed applications, the DCTLI(diode clamped three-level inverter) have been widely used. This paper describes the analysis of the neutral point current of the DCTLI and the improved space vector-based PWM strategy considering the switching frequency of power devices, that minimizes the fluctuation of the neutral point current in spite of high modulation index region and low power factor. It contributes to decrease the capacitance of dc-link capacitor bank and to increase the neutral point voltage controllable region. Especially, even if second (or even) order harmonic is induced in load current (at this situation, is was investigated that the general control method can not suppress the neutral point voltage variation), this PWM can provide effective control method to suppress the neutral point voltage variation. Various simulation results by means of Matlab/Simulation are presented to verify the proposed PWM.