• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.04b
• /
• pp.79-80
• /
• 2009

The local oxidation using an atomic force microscopy (AFM) is useful for Si-base fabrication of nanoscale structures and devices. SiC is a wide band-gap material that has advantages such as high-power, high-temperature and high-frequency in applications, and among several SiC poly types, 4H-SiC is the most attractive poly type due to the high electron mobility. However, the AFM local oxidation of 4H-SiC for fabrication is still difficult, mainly due to the physical hardness and chemical inactivity of SiC. In this paper, we investigated the local oxidation of 4H-SiC surface using an AFM. We fabricated oxide patterns using a contact mode AFM with a Pt/Ir-coated Si tip (N-type, $0.01{\sim}0.025\;{\Omega}cm$) at room temperature, and the relative humidity ranged from 40 to 50%. The height of the fabricated oxide pattern ($1{\sim}3\;nm$) on SiC is similar to that of typically obtained on Si ($10^{15}{\sim}10^{17}\;cm^{-3}$). We perform the 2-D simulation to further analyze the electric field between the tip and the surface. Whereas the simulated electric field on Si surface is constant ($5\;{\times}\;10^7\;V/m$), the electric field on SiC surface increases with increasing the doping concentration from ${\sim}10^{15}$ to ${\sim}10^{17}\;cm^{-3}$. We demonstrated that a specific electric field ($4\;{\times}\;10^7\;V/m$) and a doping concentration (${\sim}10^{17}\;cm^{-3}$) is sufficient to switch on/off the growth of the local oxide on SiC.

• Korean Journal of Materials Research
• /
• v.20 no.12
• /
• pp.629-635
• /
• 2010

Abstract In this study characteristics of Al-doped ZnO thin film by HIPIMS (High power impulse sputtering) are discussed. Deposition speed of HIPIMS with conventional balanced magnetic field is measured at about 3 nm/min, which is 30% of that of conventional RF sputtering process with the same working pressure. To generate additional magnetic flux and increase sputtering speed, electromagnetic coil is mounted at the back side of target. Under unbalanced magnetic flux from electromagnet with 1.5A coil current, deposition speed of AZO thin film is increased from 3 nm/min to 4.4 nm/min. This new value originates from the decline of particles near target surface due to the local magnetic flux going toward substrate from electromagnet. AZO film sputtered by HIPIMS process shows very smooth and dense film surface for which surface roughness is measured from 0.4 nm to 1 nm. There are no voids or defects in morphology of AZO films with varying of magnetic field. When coil current is increased from 0A to 1A, transmittance of AZO thin film decreases from 80% to 77%. Specific resistance is measured at about $2.9{\times}10-2\Omega{\cdot}cm$. AZO film shows C-axis oriented structure and its grain size is calculated at about 5.3 nm, which is lower than grain size in conventional sputtering.

• The Journal of Korean Medicine
• /
• v.30 no.4
• /
• pp.47-58
• /
• 2009

Objectives: Several domestic search systems for research projects providing capabilities of searching and managing the research information based on metadata have been completed, although they cannot search projects for specific domains such as the Oriental Medicine field. Therefore, in this paper we propose an effective method for collecting and refining information of research projects in the oriental medicine field. We also design and implement a search management system based on the collected information. Methods: We chose three search elements and defined the collecting process for research projects. The collected information was refined to enhance the quality of results. Then, the search management system was implemented by Adobe Flex. Results: We were able to collect 1,688 research projects in the oriental medicine field. We also implemented the search management system, which provides the functionalities of search and management such as input, update, delete, spreadsheet import/export of R&D projects, user management and access control. Conclusions: The collected information and the search management system will be used in a project analysis system which will be constructed in the future. The project analysis system could help to analyze trends in oriental medicine research as well as construct a technical roadmap.

• Fashion & Textile Research Journal
• /
• v.19 no.1
• /
• pp.70-78
• /
• 2017

To predict and foster professional research issues for the present and future, it is important to understand the stream of research trends. This study is to provide information of research trend through analysis of quantitative variables in 1,374 articles from the first issue to the present(2015) of the Fashion and Textiles Research Journal. As a result, in the former periods, articles in the field of textile science & technology and fashion design & historical concerns, and articles that used experiments and others as a research method were dominant; in the latter periods, articles in the field of fashion marketing & merchandising and apparel production & technology, and articles that used survey as a research method were dominant. According to each detailed research field and method, there were significant differences in the number of pages, authors and references of articles. In addition, it was found that the number of pages and the number of references increased sharply in the latter period, indicating that the contents of the papers were more detailed and faithful to references of other studies. Through the analysis of this study, it was found that Fashion and Textiles Research Journal published a variety of articles in the academic fields. The research information analyzed in this study will contribute to the future design for the research as well as the academic societies.

• Korean Journal of Soil Science and Fertilizer
• /
• v.42 no.2
• /
• pp.139-143
• /
• 2009

We examined the vertical distribution of specific microbial groups and the patterns of microbial community structure within the soil profile using phospholipid fatty acid (PLFA). Samples were collected from the soil surface down to 15 cm in depth from paddy and upland fields located in Daegu, Korea. The two fields have been fertilized with only chemical fertilizers N, P, K for 33 years. Principal component analysis of the PLFA signatures indicated that the composition of the soil microbial communities changed significantly with the cultivation practices and soil depth, suggesting that cultivation practices of paddy and upland fields had more significant influence on soil microbial community than the soil depth did. The soil microbial communities changed more drastically with soil depth in upland field than in paddy field, with making thicker soil surface in paddy field in terms of soil microbial community. The ratios of cyclopropyl/monoenoic precursors and total saturated/total monounsaturated fatty acids increased with soil depth, suggesting that the deeper soil horizons are more carbon-limited and anaerobic than surface soil. The community analysis using PLFAs as biomarkers revealed that Gram-positive bacteria and actinomycetes tended to increase in proportional abundance with increasing soil depth, while the abundance of Gram-negative bacteria and fungi were highest at the soil surface and substantially lower in the subsurface.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2006.05a
• /
• pp.326-331
• /
• 2006

The durability of recent motors is longer than the past one because there are the rapid technique development of the automobile industry and the vehicle maintenance of users. And then the importance of the durability test due to vibration is increased from day to day. So full vehicle and parts companies accomplish the durability test using various methods. The most public test method among them is the reliable field test but it bring on higher cost and period of the development process. The durability test using MAST(multi axis simulation table) is a solution in order to improve the development process of automobiles. Generally its excitation source uses the optimized road profiles that are obtained by the road test of belgian road, country road, cobbleston road and so on instead of a real field but the interrelations and influences accordingly vehicle damage are considered by a field test between specific roads and real fields in the first place. Therefore this study, in order to accomplish a basic research for the durability test using the MAST, performed on the real field driving test at various domestic roads and the results which are analyzed by PSD(power spectrum density) are compared with relative sensitivity among the roads. Consequently they can present a basic material for generation of road profiles which is applied to the durability test using MAST.

• Proceedings of the Korean Geotechical Society Conference
• /
• 1998.05a
• /
• pp.153-204
• /
• 1998

Prediction of lining loads due to tunnelling is one of the major issues to be addressed in the design of a tunnel. The objective of this study is to investigate rational and realistic design loads on tunnel linings. factors influencing the lining load are summarized and discussed. The instruments for measuring the lining loads are reviewed and discussed because field measurements are often necessary to verify the design methods. Tunnel construction in the City of Edmonton has been very active for storm and sanitary purposes. Since the early 1970's, the city has also been developing an underground Light Rail Transit system. The load measurements obtained from these tunnels are compared with the results from the existing design methods. However, none of the existing methods are totally satisfactory, Therefore, there is some room for improvement in the prediction of lining loads. The convergence-confinement method is reviewed and applied to a case history of a tunnel in Edmonton. The convergence curves are obtained from 2-D finite element analyses using three different material models and theoretical equations. The limitation of the convergence-confinement method is discussed by comparing these curves with the field measurements. Three-dimensional finite element analyses are performed to gain a better understanding of stress and displacement behaviour near the tunnel face. An improved design method is proposed based on the review of existing design methods and the performance of numerical analyses. A specific method or combination of two different methods is suggested for the estimation of lining loads for different conditions of tunnelling. A method to determine the stress reduction factor is described. Typical values of dimensionless load factors nD/H for tunnels in Edmonton are obtained from parametric analyses. Finally, the loads calculated using the proposed method are compared with field measurements collected from various tunnels in terms of soil types and construction methods to verify the method. The proposed method gives a reasonable approximation of the lining loads. The proposed method is recommended as an approximate guideline for the design of tunnels, but the results should be confirmed by field measurements due to the uncertainties of the ground and lining properties and the construction procedures, This is the reason that in-situ monitoring should be an integral part of the design procedure.

• Journal of the Korean Geotechnical Society
• /
• v.15 no.2
• /
• pp.129-138
• /
• 1999

This study is performed for the development of a field monitoring and test technique both of self-weight and hydraulic consolidation by which the soil parameters of dredge-reclaimed clay can be obtained effectively. The field monitoring development and tests mentioned above make it possible to reproduce the process of the self-weight consolidation from settling to reclaimed soft ground. The experimental research is mainly focussed on the characteristics of self-weight consolidation of dredged clayey soil. And theoretical study has pointed out the limits in the application of Terzaghi's one dimensional consolidation theory in interpreting reclaimed clayey ground. Furthermore, a finite difference analysis has been made on the basis of Mikasa s self-weight consolidation theory which takes the problems of Terzaghi's theory into consideration. The relationships between specific volume, effective stress, and the coefficient of permeability of Kunsan reclaimed clayey soil have been obtained by laboratory tests. On the other hand, through the field monitoring, pore pressure, total pressure, and water levels have been measured after pouring. The results of these experiments have been analyzed, and compared with those from Terzaghi's method and the finite difference analysis of Mikasa's self-weight consolidation theory. In conclusion, the measured settlements is comparatively consistent with Mikasa's self-weight consolidation theory rather than Terzaghi's consolidation theory.

• Annals of Clinical Neurophysiology
• /
• v.8 no.2
• /
• pp.163-170
• /
• 2006

Backgrounds: MEG can measure the task-specific neurophysiologic activity with good spatial and time resolution. Language lateralization using noninvasive method has been a subject of interest in resective brain surgery. We purposed to develop a paradigm for language lateralization using MEG and validate its feasibility. Methods: Magnetic fields were obtained in 12 neurosurgical candidates and one volunteer for language tasks, with a 306 channel whole head MEG. Language tasks were word listening, reading and picture naming. We tested two word listening paradigms: semantic decision of meaning of abstract nouns, and recognition of repeated words. The subjects were instructed to silently name or read, and respond with pushing button or not. We decided language dominance according to the number of acceptable equivalent current dipoles (ECD) modeled by sequential single dipole, and the mean magnetic field strength by root mean square value, in each hemisphere. We collected clinical data including Wada test. Results: Magnetic fields evoked by word listening were generally distributed in bilateral temporoparietal areas with variable hemispheric dominance. Language tasks using visual stimuli frequently evoked magnetic field in posterior midline area, which made laterality decision difficult. Response during task resulted in more artifacts and different results depending on responding hand. Laterality decision with mean magnetic field strength was more concordant with Wada than the method with ECD number of each hemisphere. Conclusions: Word listening task without hand response is the most feasible paradigm for language lateralization using MEG. Mean magnetic field strength in each hemisphere is a proper index for hemispheric dominance.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2004.03a
• /
• pp.262-270
• /
• 2004

Basic experiments were carried out using the THT-IV low-power Hall thruster to examine the influences of magnetic field shape and strength, and acceleration channel length on thruster performance and to establish guidelines for design of high-performance Hall thrusters. Thrusts were measured with varying magnetic field and channel structure. Exhaust plasma diagnostic measurement was also made to evaluate plume divergent angles and voltage utilization efficiencies. Ion current spatial profiles were measured with a Faraday cup, and ion energy distribution functions were estimated from data with a retarding potential analyzer. The thruster was stably operated with a highest performance under an optimum acceleration channel length of 20 mm and an optimum magnetic field with a maximum strength of about 150 Gauss near the channel exit and with some shape considering ion acceleration directions. Accordingly, an optimum magnetic field and channel structure is considered to exist under an operational condition, related to inner physical phenomena of plasma production, ion acceleration and exhaust plasma feature. A new Hall thruster was designed with basic research data of the THT-IV thruster. With the thruster with many considerations, long stable operations were achieved. In all experiments at 200-400 V with 1.5-3 mg/s, the thrust and the specific impulse ranged from 15 to 70 mN and from 1100 to 2300 see, respectively, in a low electric power range of 300~1300 W. The thrust efficiency reached 55 %. Hence, a large map of the thruster performance was successfully made. The thermal characteristics were also examined with data of both measured and calculated temperatures in the thruster body. Thermally safe conditions were achieved with all input powers.