• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.11a
• /
• pp.167-171
• /
• 2003

We report the material and electrical properties of $CoSi_2$ and $NiSi_2$contacts to n-type 4H-SiC depending on the post-annealing and the metal covering conditions. The Ni and Co silicides are deposited by RF sputtering with Ni/Si/Ni and Co/Si/Co films separately deposited on 4H-SiC substrates. The deposited films are annealed at $800\;^{\circ}C$ in $Ar:H_2$ (9:1) gas ambient. Results of the specific surface resistivity measurements show that the resistivity of the Co-based metal contact was the one order lower than that of the Ni-based contact. The specific contact resistance was measured by a transmission line technique, and the specific contact resistivity of $1.5{\times}10^{-6}\;{\Omega}\;cm^2$ is obtained for Co/Si/Co metal structures after a two-step annealing; at $550\;^{\circ}C$ for 10 min and $800\;^{\circ}C$ for 3min. The physical properties of the contacts were examined by using XRD and AES, and the results indicate that the Co-based metal contacts have better structural stability of silicide phases formed after the high temperature annealing.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.17 no.7
• /
• pp.764-769
• /
• 2004

In order to reduce operating voltage of the GaN based blue-violet laser diodes, the effect of highly Mg doped GaN layer, which was grown below ohmic contact metals, on contact resistivity as well as operating voltage has been investigated. The addition of the highly Mg doped GaN layer greatly reduced contact resistivity of Pd/Pt/Au ohmic contacts from $5.2 \times {10}^-2 \Omegaㆍ$\textrm{cm}^2$ to 7.5 \times {10}^-4 \Omegaㆍ$\textrm{cm}^2$$. In addition, it also decreased device voltage at 20 mA by more than 3 V. Temperature- dependent sheet resistivity of the highly Mg doped GaN layer suggested that the reduction of the contact resistivity could be attributed to predominant current flow at the interface between the Pd/Pt/Au contacts and p-GaN through a deep level defect band, rather than the valence band.

• Journal of Sensor Science and Technology
• /
• v.15 no.6
• /
• pp.386-390
• /
• 2006

This paper describes the ohmic contact formation of polycrystalline 3C-SiC films deposited on thermally grown Si wafers. In this work, a TiW (titanium tungsten) film as a contact material was deposited by RF magnetron sputter and annealed with the vacuum process. The specific contact resistance (${\rho}_{c}$) of the TiW contact was measured by using the C-TLM (circular transmission line method). The contact phase and interfacial reaction between TiW and 3C-SiC at high-temperature as also analyzed by XRD (X-ray diffraction) and SEM (scanning electron microscope). All of the samples didn't show cracks of the TiW film and any interfacial reaction after annealing. Especially, when the sample was annealed at $800^{\circ}$ for 30 min., the lowest contact resistivity of $2.90{\times}10{\Omega}cm^{2}$ was obtained due to the improved interfacial adhesion. Therefore, the good ohmic contact of polycrystalline 3C-SiC films using the TiW film is very suitable for high-temperature MEMS applications.

• Korean Journal of Materials Research
• /
• v.9 no.10
• /
• pp.1012-1017
• /
• 1999

Low resistance ohmic contacts to the Si-doped $\textrm{In}_{0.17}\textrm{Ga}_{0.83}\textrm{N}$(~$\times10^{19}\textrm{cm}^{-3}$) were obtained using the W metallization schemes. Specific contact resistance decreased with increasing annealing temperature. The lowest resistance is obtained after a nitrogen ambient annealing at $950^{\circ}C$ for 90 s, which results in a specific contact resistance of $2.75\times10^{-8}\Omega\textrm{cm}^{-3}$. Interfacial reactions and surface are analyzed using x-ray diffraction and scanning electron microscopy (SEM). The X-ray diffraction results show that the reactions between the W film and the $\textrm{In}_{0.17}\textrm{Ga}_{0.83}\textrm{N}$ produce a $\beta$-$W_2N$ phase at the interface. The SEM result shows that the morphology of the contacts is stable up to a temperature as high as $850^{\circ}C$. Possible mechanisms are proposed to describe the annealing temperature dependence of the specific contact resistance.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.17 no.2
• /
• pp.283-287
• /
• 2017

Recently, Ni-InGaAs has been required for high-performance III-V MOSFETs as a promising self-aligned material for doped source/drain region. As downscaling of device proceeds, reduction of contact resistance ($R_c$) between Ni-InGaAs and n-InGaAs has become a challenge for higher performance of MOSFETs. In this paper, we compared three types of sample, vacuum, 2% $H_2$ and 4% $H_2$ annealing condition in rapid thermal annealing (RTA) step, to verify the reduction of $R_c$ at Ni-InGaAs/n-InGaAs interface. Current-voltage (I-V) characteristic of metal-semiconductor contact indicated the lowest $R_c$ in 4% $H_2$ sample, that is, higher current for 4% $H_2$ sample than other samples. The result of this work could be useful for performance improvement of InGaAs n-MOSFETs.

• Transactions on Electrical and Electronic Materials
• /
• v.17 no.3
• /
• pp.143-145
• /
• 2016

In order to find suitable source and drain (S/D) electrodes for amorphous InGaZnO thin film transistors (a-IGZO TFTs), the specific contact resistance of interface between the channel layers and various S/D electrodes, such as Ti/Au, a-IZO and multilayer of a-IGZO/Ag/a-IGZO, was investigated using the transmission line model. The a-IGZO TFTs with a-IGZO/Ag/a-IGZO of S/D electrodes had good performance and low contact resistance due to the homo-junction with channel layer. The stability was measured with different electrodes by a positive bias stress test. The result shows the a-IGZO TFTs with a-IGZO/Ag/a-IGZO electrodes were more stable than other devices.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1998.11a
• /
• pp.151-154
• /
• 1998

We have investigated a correlation of the electrical properties of the Pd/Ge/Pd/Ti/Au ohmic contact on n-InGaAs with its microstructures for the high temperature application of compound semiconductor devices. The samples were heat-treated by the rapid thermal annealing at various temperatures. In the contact system, moderately good specific contact resistance was obtained even before annealing because of the low metals-InGaAs barrier height, and better ohmic performances were observed by annealing up to 400˚C. But the ohmic performance was degraded after annealing at 450˚C due to the increment of Pd$_2$Ga$\sub$5/ phases.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.490.2-490.2
• /
• 2014

Since the general solar cells accept sun light at the front side, excluding the electrode area, electrons move from the emitter to the front electrode and start to collect at the grid edge. Thus the edge of gridline can be important for electrical properties of screen-printed silicon solar cells. In this study, the improvement of electrical properties in screen-printed crystalline silicon solar cells by contact treatment of grid edge was investigated. The samples with $60{\Omega}/{\square}$ and $70{\Omega}/{\square}$ emitter were prepared. After front side of samples was deposited by SiNx commercial Ag paste and Al paste were printed at front side and rear side respectively. Each sample was co-fired between $670^{\circ}C$ and $780^{\circ}C$ in the rapid thermal processing (RTP). After the firing process, the cells were dipped in 2.5% hydrofluoric acid (HF) at room temperature for various times under 60 seconds and then rinsed in deionized water. (This is called "contact treatment") After dipping in HF for a certain period, the samples from each firing condition were compared by measurement. Cell performances were measured by Suns-Voc, solar simulator, the transfer length method and a field emission scanning electron microscope. According to HF treatment, once the thin glass layer at the grid edge was etched, the current transport was changed from tunneling via Ag colloids in the glass layer to direct transport via Ag colloids between the Ag bulk and the emitter. Thus, the transfer length as well as the specific contact resistance decreased. For more details a model of the current path was proposed to explain the effect of HF treatment at the edge of the Ag grid. It is expected that HF treatment may help to improve the contact of high sheet-resistance emitter as well as the contact of a high specific contact resistance.

• Korean Journal of Materials Research
• /
• v.19 no.8
• /
• pp.417-420
• /
• 2009

This study develops a highly transparent ohmic contact using phosphorus doped ZnO with current spreading for p-GaN to increase the optical output power of nitride-based light-emitting diodes (LEDs). The phosphorus doped ZnO transparent ohmic contact layer was prepared by radio frequency magnetron sputtering with post-deposition annealing. The transmittance of the phosphorus doped ZnO exceeds 90% in the region of 440 nm to 500 nm. The specific contact resistance of the phosphorus doped ZnO on p-GaN was determined to be $7.82{\times}10^{-3}{\Omega}{\cdot}cm^2$ after annealing at $700^{\circ}C$. GaN LED chips with dimensions of $300\times300{\mu}m$ fabricated with the phosphorus doped ZnO transparent ohmic contact were developed and produced a 2.7 V increase in forward voltage under a nominal forward current of 20 mA compared to GaN LED with Ni/Au Ohmic contact. However, the output power increased by 25% at the injection current of 20 mA compared to GaN LED with the Ni/Au contact scheme.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.265.1-265.1
• /
• 2016

여러 application에 적용하기 위하여 p-type SnO 박막과 전극 간의 접촉 저항을 분석이 필요하였다. 이를 Transmission Line Method(TLM) 패턴 소자를 제작한 후 전기적 특성을 분석함으로써 알 수 있었다. $Si/SiO_2$ 기판에 Reactive Magnetron Sputtering법을 이용하여 c축 우선 배향된 SnO를 100nm 증착하고 photolithography 공정을 통해 전극을 패턴화하여 100nm 두께로 증착하였다. 전극 간 거리는 1, 2, 4, 8, 16, 32, 64, 128, 256, 512, $1024{\mu}m$로 각각 2배씩 증가하는 패턴이고 폭 W는 $300{\mu}m$ 이다. p-type SnO 의 경우, work function이 4.8eV이기 때문에 전극과 ohmic contact이 되기 위해서는 4.8eV보다 높은 work function 값을 가지는 전극이 필요하였다. 이 조건과 맞는 후보로 Ni(5.15eV), ITO(5.3eV)를 설정한 후 소자를 제작하였다. 제작된 소자는 열처리 하지 않은 소자와 Rapid Thermal Annealing(RTA) 장비에서 $100^{\circ}C$, $200^{\circ}C$, $300^{\circ}C$에서 각각 1분씩 열처리한 소자의 특성을 분석하였다. 열처리 하지 않은 소자의 경우 Ni 전극의 specific contact resistance는 $3.42E-2{\Omega}$의 값을 나타내었고, ITO의 경우 $3.62E-2{\Omega}$값을 나타내었다.