• 한국결정성장학회지
• /
• 제20권1호
• /
• pp.30-34
• /
• 2010

중고온용 열전 소재로 우수한 특성을 나타내는 $CoSb_3$계 소재의 열전 소자 제조를 위해 방전플라즈마 소결법을 이용하여 소결 및 Cu-Mo 전극 소재와의 접합을 동시에 실시하였다. $CoSb_3$ 내부로의 Cu 확산을 방지하기 위해 Ti을 중간층으로 삽입하였으며 열팽창계수의 조절을 위해 Cu : Mo = 3 : 7 부피비 조성을 선택하였다. 삽입된 Ti과 $CoSb_3$는 $TiSb_2$ 이 차상을 형성하면서 접합이 진행되었지만 접합 온도 및 접합 시간의 증가에 따라 TiSb 및 TiCoSb 등의 상의 형성에 의해 접합 계면에서 균열이 발생되어 접합 특성을 악화시키는 것으로 밝혀졌다.

• 한국분말재료학회지
• /
• 제28권4호
• /
• pp.336-341
• /
• 2021

In this study, a nanocrystalline FeNiCrMoMnSiC alloy was fabricated, and its austenite stability, microstructure, and mechanical properties were investigated. A sintered FeNiCrMoMnSiC alloy sample with nanosized crystal was obtained by high-energy ball milling and spark plasma sintering. The sintering behavior was investigated by measuring the displacement according to the temperature of the sintered body. Through microstructural analysis, it was confirmed that a compact sintered body with few pores was produced, and cementite was formed. The stability of the austenite phase in the sintered samples was evaluated by X-ray diffraction analysis and electron backscatter diffraction. Results revealed a measured value of 51.6% and that the alloy had seven times more austenite stability than AISI 4340 wrought steel. The hardness of the sintered alloy was 60.4 HRC, which was up to 2.4 times higher than that of wrought steel.

• 한국세라믹학회:학술대회논문집
• /
• 한국세라믹학회 2003년도 춘계총회 및 연구발표회 초록집
• /
• pp.97.1-97
• /
• 2003

• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 2006년도 Extended Abstracts of 2006 POWDER METALLURGY World Congress Part 1
• /
• pp.554-554
• /
• 2006

• 한국분말재료학회지
• /
• 제13권4호
• /
• pp.269-277
• /
• 2006

[ ${\beta}-W(W_3O)$ ] oxide layer on the surface of each W(tungsten) nanopowder produced by the electric explosion of wire(EEW) process were formed during the 1vol.% air passivation process. The oxide layer hindered sintering densification of compacts during SPS process. The oxide phase was reduced to the pure W phase during SPS. The W nanopowder's compacts treated by the hydrogen reduction showed high sintered density of 94.5%. after SPS process at $1900^{\circ}C$.

• 한국분말재료학회지
• /
• 제27권5호
• /
• pp.373-380
• /
• 2020

The purpose of this study is to investigate the densification behavior and the corresponding microstructural evolution of tantalum and tantalum-tungsten alloy powders for explosively formed liners. The inherent inhomogeneous microstructures of tantalum manufactured by an ingot metallurgy might degrade the capability of the warhead. Therefore, to overcome such drawbacks, powder metallurgy was incorporated into the near-net shape process in this study. Spark plasma-sintered tantalum and its alloys with finer particle sizes exhibited higher densities and lower grain sizes. However, they were contaminated from the graphite mold during sintering. Higher compaction pressures in die and isostatic compaction techniques also enhanced the sinterability of the tantalum powders; however, a full densification could not be achieved. On the other hand, the powders exhibited full densification after being subjected to hot isostatic pressing over two times. Consequently, it was found that the hot isostatic-pressed tantalum might exhibit a lower grain size and a higher density as compared to those obtained in previous studies.

• 한국세라믹학회지
• /
• 제46권5호
• /
• pp.505-509
• /
• 2009

In this study, bulk nano-crystalline $Si_3N_4$ ceramics were fabricated by spark plasma sintering (SPS) and their mechanical properties, in particular wear, were investigated. A wide range of grain sizes, from 80 nm and 250 nm were obtained by varying sintering conditions ($1550^{\circ}C$-5 min to $1650^{\circ}C$-20 min). The elastic modulus of obtained ceramics was ${\sim}250$ GPa and hardness was in the range of $13{\sim}14$ GPa. The indentation fracture toughness increased from $2.58MPa{\cdot}m^{1/2}$ to $3.24MPa{\cdot}m^{1/2}$ with increasing sintering temperature possibly due to the elongated grains. Sliding wear tests revealed at least an order magnitude improvement in wear resistance with grain refinement. Microstructure analysis indicated that nano-$Si_3N_4$ specimens worn mainly through delamination and microcracking, while that of coarser specimens revealed severe wear with grain debonding and fracture.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2009년도 추계학술대회 논문집
• /
• pp.87-87
• /
• 2009

The composites were fabricated by adding 30, 40, 50, 60[vol.%] Zirconium Diboride(hereafter, $ZrB_2$) powders as a second phase to Silicon Carbide(hereafter, SiC) matrix. SiC-$ZrB_2$ composites were sintered by Spark Plasma Sintering(hereafter, SPS) in argon gas atmosphere. The relative density SiC+30[vol.%]$ZrB_2$, SiC+40[vol.%]$ZrB_2$, SiC+50[vol.%]$ZrB_2$ and SiC+60[vol.%]$ZrB_2$ composites are 94.98[%], 99.57[%], 96.58[%] and 93.62[%] respectively.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2009년도 추계학술대회 논문집
• /
• pp.105-105
• /
• 2009

The composites were fabricated by adding 30, 35, 40, 45[vol.%] Zirconium Diboride(hereafter, $ZrB_2$) powders as a second phase to Silicon Carbide(hereafter, SiC) matrix. $SiC-ZrB_2$ composites were sintered by Spark Plasma Sintering(hereafter, SPS) in vacuum or argon gas atmosphere. The relative density of SiC+40[vol.%]$ZrB_2$ composites reveal high 99.57[%] in argon gas atmosphere and pressure 50MPa.

• 한국재료학회:학술대회논문집
• /
• 한국재료학회 2003년도 추계학술발표강연 및 논문개요집
• /
• pp.84-84
• /
• 2003

The effects of Ti addition on microstructure and mechanical properties of (Al+Xat.%Ti)2at%B (X=0.5, 1, 2) fabricated by mechanical alloying and spark plasma sintering (SPS) were investigated. These alloys were prepared by high energy ball milling (attritor) and then fracture toughness was investigated by using a charpy impact tester. The SPS method was used to consolidate (Al+Xat.%Ti)fat.%B with the pressure of 50MPa. The powders were successfully consolidated to alloy which the theoretical density is 99%. It was confirmed that the fracture toughness of Al-Bat.% matrix composites was increased by the addition of Ti.