• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.10 no.5
• /
• pp.2375-2393
• /
• 2016

Key agreement is paramount in secure wireless communications. A promising approach to address key agreement schemes is to extract secure keys from channel characteristics. However, because channels lack randomness, it is difficult for wireless networks with stationary communicating terminals to generate robust keys. In this paper, we propose a Robust Secure Key Agreement (RSKA) scheme from Received Signal Strength (RSS) in stationary wireless networks. In order to mitigate the asymmetry in RSS measurements for communicating parties, the sender and receiver normalize RSS measurements and quantize them into q-bit sequences. They then reshape bit sequences into new l-bit sequences. These bit sequences work as key sources. Rather than extracting the key from the key sources directly, the sender randomly generates a bit sequence as a key and hides it in a promise. This is created from a polynomial constructed on the sender's key source and key. The receiver recovers the key by reconstructing a polynomial from its key source and the promise. Our analysis shows that the shared key generated by our proposed RSKA scheme has features of high randomness and a high bit rate compared to traditional RSS-based key agreement schemes.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.44 no.7
• /
• pp.14-24
• /
• 2002

The effect of reclaimed water irrigation on paddy rice culture was evaluated by pilot study at the experimental field of Konkuk University in Seoul, Korea. The sewage was treated by constructed wetland system, and its effluent was used as irrigation water for four treatments and one control plots with three replications. Irrigation of reclaimed water onto paddy rice cultures did not adversely affect the growth and yield of rice. Instead, experimental rice plots of reclaimed water irrigation displayed about 10 to 50% more yield on average than controls. This implies that reclaimed water irrigation might be beneficial rather than harmful to rice culture as long as the sewage is treated adequately and used properly. The amount of irrigation water had little effect on experimental rice cultures, but its strength was important. The strength of treated sewage was not a limiting factor in this study, and no lodging was observed even with a relatively high nitrogen concentration (up to 160mg/L). In general the paddy soil was not affected by reclaimed water irrigation. However, there was an indication that continuous irrigation with high strength of reclaimed water might cause salt accumulation in the soil. Supplemental use of reclaimed water with existing sources of irrigation water is recommended rather than irrigation with a single source of reclaimed water. Overall, the results demonstrated that reclaimed water could be reused as a supplemental source of irrigation water for paddy rice culture without causing adverse effects as long as it is properly managed. For full-scale application, further investigation should be done on environmental risks, tolerable water quality, and fraction of supplemental irrigation.

• Food Science of Animal Resources
• /
• v.43 no.1
• /
• pp.61-72
• /
• 2023

The practical use of Korean native black goat skin as a source of gelatin extraction is limited. The objective of this study was to optimize the extraction temperature and time of gelatin from Korean native black goat skin, and to compare the quality characteristics of goat skin gelatin and other commercial gelatin products. Response surface methodology was applied to optimize the extraction temperature and time of gelatin obtained from native Korean black goat skin. The effects of temperature (50℃-70℃) and time (2-4 h) on extraction yield and gel strength were investigated using a face-centered central composite design with 13 experiments. Gelatin extraction from Korean native black goat skin was prepared through the serial processes of alkali pre-treatment, bleaching, neutralization, hot-water extraction, and freeze-drying. Using the optimization plot of Minitab software, the optimized conditions for extracting temperature and time of goat skin gelatin were 59.49℃ and 3.03 h, and the optimized values of extraction yield and gel strength were 12.52% and 263.37 g, respectively. Based on a quality comparison of goat skin gelatin with commercial gelatin, the pH value of gelatin extracted from Korean native black goat skin was 5.57. The color of gelatin extracted from Korean native black goat skin was darker than that of commercial gelatin (p<0.05). Higher emulsifying properties and gel strength of goat skin gelatin were observed when compared to those of commercial gelatin (p<0.05). Therefore, the results of this study indicate that Korean native black goat skin may be a valuable source for gelatin extraction.

• Journal of Ship and Ocean Technology
• /
• v.3 no.4
• /
• pp.35-51
• /
• 1999

Fatigue strength assessment procedures have been implemented in the ship design rules by many classification societies. However, a large variation tin the details of the different approaches exists in practically all aspects influding load history assessment, stress evaluation and fatigue strength assessment. In order to assess the influences of thesd variations on the prediction of fatigue lives. a comparative study is organized by the ISSC Committee III.2 Fatigue and Fracture. A pad detail on the top of longitudinal hatch coaming of a panamax container vessel is selected for fatigue calculation. The work described in this paper is one set of results of this comparative study in which the ABS dynamics approach is applied. Through this analysis the following conclusions can be drawn. (1) With the original ABS approach, the fatigue life of this pad detail is very low, only 2.398 years. (2) The treatment of the stillwater bending moment in the ABS approach might be a source of conservatism. If the influence of stillwater bending moment is ignored, then the fatigue life for this pad detail is 7.036 years. (3) The difference between the nominal stress approach and the hot spot stress approach for this pad detail is about 26%.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.21 no.2
• /
• pp.290-296
• /
• 2012

Cold-rolled carbon steel sheets are commonly used in railroad car or commercial vehicles such as the automobile. These are mainly fabricated by spot welding which is a kind of electric resistance welding. But fatigue strength of spot welding joint is lower than that of base metal due to high stress concentration at nugget edge of the spot welded part. And fatigue strength of them is especially influenced by not only geometrical and mechanical factors but also welding conditions of the spot welded joint. So for fatigue design of gas welded joints such as TS-type joints, it is necessary to obtain design information on stress distribution at the weldment as well as fatigue strength of spot welded joints. And also, the influence of the geometrical parameters of spot welded joints on stress distribution and fatigue strength must be evaluated. And analysis approach for fatigue test using design of experiment are evaluated optimum factor in TS-type welded joint and geometrical parameters of materials. Using these results, that factors applied to fundamental information for automation of fatigue design.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.31 no.1A
• /
• pp.16-22
• /
• 2006

This papers described with the analysis for electric Field strength on ground level transmitted from DMB transponder in stratosphere HAPS. It is compare with horizontal propagated ground wave. Resultly we confirm the equal strength a electric field on ground level between hish altitude vertical propagated wave and horizontal ground wave, also, is only 1W compare with terrestrial facility as transmitted output power for the DMB transponder in stratosphere HAPS. It is corresponding to 1Kw as same power value in ground propagated wave. Lastly it is new material wave source and also we concluding remarks as ubiquitous communication networking media.

• Journal of Powder Materials
• /
• v.1 no.2
• /
• pp.181-189
• /
• 1994

The compacts of pure and phosphorus-coated iron powder with 0~0.8%C were sintered at $1100^{\circ}C$ for 40 min. in cracked ammonia gas atmosphere. The tensile and impact strengths were measured and the relationship of the results with carbon content, phosphorus, quenching and tempering was investigated. The results obtained can be summarized as follows : (1) The tensile strength of sintered compacts increased slowly with carbon content. Increase in tensile strength by heat treatment was evident especially in the low carbon specimen. The specimen with phosphorus showed higher strength compared to pure iron compacts value. (2) No inflection point of elasticplastic deformation on stress-strain curve was observed in sintered steel. The elastic modulus of sintered steel had the same tendency as tensile strength. But the elongation showed the opposite tendency. (3) The impact absorption energy of sintered steel without addition of phosphorus decreased successively with carbon content and by quenching and tempering. On the contrary, addition of phosphorus resulted in an increase of the impact absorption energy. Quenching and tempering did not affect the impact energy especially in high carbon content. (4) The main fracture source was pore in specimen and the propagation of crack occured mostly along the grain boundaries. But the intragranular fracture was also observed in high carbon, quenched and tempered specimen, and especially in the specimen with phosphorus.

• Journal of Welding and Joining
• /
• v.34 no.2
• /
• pp.67-72
• /
• 2016

Aluminum alloy is one of light weight material and it is used to make LNG tank and ship. However, in order to weld aluminum alloy high density heat source is needed. In this paper, I-butt welding of Al 5083 with 6mm thickness using Plasma-MIG welding was carried out. The experiment was performed to investigate the influence of plasma-MIG welding parameters such as plasma current, wire feeding rate, MIG-welding voltage and welding speed on the tensile strength of weld. In addition we suggested 3 strength estimation models which are second order polynomial regression model, multiple nonlinear regression model and neural network model. The estimation performance of 3 models was evaluated in terms of average error rate (AER) and their values were 0.125, 0.238, and 0.021 respectively. Neural network model which has training concept and reflects non -linearity was best estimation performance.

• The Journal of the Acoustical Society of Korea
• /
• v.33 no.3
• /
• pp.153-162
• /
• 2014

Empirical prediction method of the acoustic load on the fairing is based on jet experimental data on the basis of similarity principle. Representative empirical prediction method, DSM-II(Distributed Source Method-II), is a distributing source method along the jet plume. But the empirical prediction model is limited to reflect the impingement source in real environment because it is based on the free jet data. So, we propose a empirical prediction method considering the impinging jet effect by adding a impingement source in the existing prediction method. Considering the additional source's displacement, spectrum, strength and directivity, we calculate the acoustic load on the KSR-III(Korean Sounding Rocket-III) rocket and compare the results with the existing method and experiment data.

• Advances in materials Research
• /
• v.9 no.3
• /
• pp.219-231
• /
• 2020

The aim of this study is to investigate the durability of fly ash based geopolymer mortar with and without protective coatings in aggressive chemical environments. The source materials for geopolymer are Fly ash and Ground Granulated Blast furnace Slag (GGBS) and they are considered in the combination of 80% & 20% respectively. Two Molarities of NaOH solution were considered such as 8M and 10M. The ratio of binder to sand and Sodium silicate to Sodium hydroxide solution (Na₂SiO₃/NaOH) are taken as 1:2 and 2 respectively. The alkaline liquid to binder ratio is 0.4. Compressive strength tests were conducted at various ages of the mortar specimens. In order to evaluate the performance of coatings on geopolymer mortar under aggressive chemical environment, the mortar specimens were coated with two different types of coatings such as epoxy and Acrylic. They were then subjected to different chemical environments by immersing them in 10% standard solutions of each ammonium nitrate, sodium chloride and sulphuric acid. Drop in compressive strength as a result of chemical exposure was considered as a measure of chemical attack and the drop in compressive strength was measured after 30 and 60 days of chemical exposure. The compressive strength results following chemical exposure indicated that the specimens containing the acrylic coating proved to be more resistant to chemical attacks. The control specimen without coating showed a much greater degree of deterioration. Therefore, the application of acrylic coating was invariably much more effective in improving the compressive strength as well as the resistance of mortar against chemical attacks. The results also indicated that among all the aggressive attacks, the sulphate environment has the most adverse effect in terms of lowering the strength.