• Journal of Korean Society of Environmental Engineers
• /
• v.36 no.9
• /
• pp.597-603
• /
• 2014

The aim of the present study is to compare sound performance depending on thickness, materials, and structure of polymer soundproof panels consisting of PC, PMMA, HDPE, and PP, respectively. As a result of comparing sound transmission loss (STL) of single layer panel made of four types of polymer, the better sound transmission loss was obtained in order of PC, PMMA, HDPE, and PP, which was obviously followed mass law. 8 mm of single panel showed 5~6 dB(A) greater STL than that of 4 mm panels and lower frequency for coincidence effect so that STL of 8 mm panels decreased around 4,000~5,000 Hz, indicating less STL of 4 mm panels than those of 8 mm. When it comes to structure, 4 mm panels with air layer appeared similar value of STL with 8 mm single panels under 300 Hz. In range of high frequency above 2,000 Hz, 4 mm panels with air layer performed better than 8 mm of single layer panel while resonance effects were observed at 500~630 Hz. It was found that these results could be practically utilized as fundamental data for noise barriers design considering the change to each condition.

• Journal of Power System Engineering
• /
• v.14 no.2
• /
• pp.55-59
• /
• 2010

In the study, it is considered sporty car as 1400cc entry cars using sound generator. These cars are required special sound quality, also sporty sound quality. The operational principle of this sound generator system is that on the operation of the engine intake valves caused pulsating is to shake the membrane of the sound generator on the inside of the driver front dash panel through the intake manifold, which will deliver the required sound quality and tone. For the component constructed sound generator, main design parameters are selected and optimized using the daguchi's method. The results are as follows; The C2 sound level must be minimized and C4 level must be maximized. And also overall level keeps linear characteristics.

• The Journal of the Acoustical Society of Korea
• /
• v.39 no.4
• /
• pp.270-278
• /
• 2020

In this paper, sound transmission of Micro-Perforated Plates (MPPs) installed in an impedance tube with a circular cross-section is described using an analytic method. Vibration of the plates is expressed in terms of an infinite series of modal functions, where modal function in the radial direction is given by the Bessel function. Under the plane wave assumption, a low frequency approximation is derived, and a formula for the sound transmission coefficient of multi-layered MPPs is presented using the transfer matrix method. The Sound Transmission Losses (STLs) of single and double MPPs are computed using the proposed method and compared with those done by the Finite Element Method (FEM), which shows an excellent agreement. As the perforation increases, the STL is degraded, since the STL becomes dominated by the perforation ratio rather than by vibration of the plate. The STL shows dips at natural frequencies as well as at the mass-spring-mass resonance frequency. The proposed model for the STL prediction in this study can be applied to an arbitrary number of MPPs, where each MPP may or may not have a perforation.

• Bulletin of the Society of Naval Architects of Korea
• /
• v.50 no.2
• /
• pp.64-68
• /
• 2013

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.35 no.5
• /
• pp.567-574
• /
• 2011

Aluminum extruded panels are widely used instead of corrugated steel panels for weight reduction in high-speed trains. Of the layers in the train body, it makes the largest contribution to the sound insulation. However, compared with that of a flat panel with the same weight, the TL of the aluminum extruded panel is remarkably lower in the local resonance frequency band. We study aluminum extruded panels for next-generation 400-km/h trains. We investigate the problem of sound insulation and propose a practical method to improve the sound-insulation performance. The local resonance frequency region is increased by a modification of the core structure, and urethane foam is placed in the core. The effect on the sound insulation is verified by experiments. Finally, the improvement for the entire sound-transmission loss is estimated for the layered floor panels of express trains.

• The Journal of the Acoustical Society of Korea
• /
• v.6 no.3
• /
• pp.17-22
• /
• 1987

This study is to propose more reliable test method in evaluating the sound insulation performance of building element in fields. This method involves the measurements of the incident acoustic intensity and transmitted surface intensity. The incident intensity is determined from measurements of the space averaged sound pressure level in source room. The transmitted surface intensity is measured directly using one microphone and one accelerometer. The results of experiments indicate that this new method makes it possible to give more reliable data than the conventional field test method. The values of trans-mission loss measured by this new method are compared favorably with those obtained using the sound intensity method and theoretical calculation(mass law).

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2007.11a
• /
• pp.1415-1418
• /
• 2007

When a high voltage COS fuse becomes a short circuit by the over current, the impulse noise over 150 dB(A) with the strong pulse jet is radiated from the COS fuse of an electric transformer. For the purpose of the impulse noise reduction, in this study, a reactive type silencer with perforated panels are considered. The transmission loss of the silencer are calculated by transfer matrix method. The effect of the porosity, the distance between panels, and the number of perforated panel on the sound transmission loss is investigated and discussed.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.17 no.10
• /
• pp.950-957
• /
• 2007

This paper considers acoustic characteristics of silencer within a dry vacuum pump. The main objective is to reduce noise in dry vacuum pump using the new designed silencer. First, SPL and sound intensity are measured for noise source identification and the new model silencer is designed corresponding to noise characteristics. 4-pole parameters are used to predict the transmission loss which is one of the interest characteristics of the new silencer. The calculated transmission loss is then used to change main effective factor and optimal value is selected by using design of experiment. By conducting an experiment, it is proved that the new designed silencer has reduced noise level by 6 dB(A) more than the original one.

• Composites Research
• /
• v.17 no.3
• /
• pp.15-22
• /
• 2004

Acoustic load generated by rocket propulsion system is one of major dynamic loads during lift-off phase so that it causes the structural failure and electronic malfunction of payloads. Acoustic loads can be greatly reduced by an appropriate acoustical design of nose faring structures. This paper deals with the acoustical design of the nose fairing structure for launch vehicle. It is well known that a honeycomb sandwich structure is a poor sound insulator because of its high specific stiffness. In this paper, the sound transmission characteristics of four kinds of honeycomb structures for noise fairing were investigated by means of numerical and experimental ways. In order to estimate transmission loss, infinite plate theory by Moore and Lyon and statistical energy analysis (SEA) method were used. The predicted results showed a good agreement with measured ones. These enabled us to determine a proper core material for nose fairing, which shows good sound insulation performance per weight.

• Proceedings of the KSR Conference
• /
• 2011.10a
• /
• pp.2256-2262
• /
• 2011

In this study, sound transmission loss (STL) is investigated on the multi-layered windows used in the KTX-sancheon and next generation HEMU-400x high speed train. Using TLOSS, which is developed as a special purpose STL analysis program, STLs of the multi-layered glass windows are analytically investigated and compared with the mass law result. Window specimens for the two train models are manufactured and intensity transmission losses are measured based on ASTM E2249-02. The problems in aspect of sound insulation are diagnosed on the two window models. The aim of this study is to provide useful data for the improvement of the interior noise in the high speed train.