• Corrosion Science and Technology
• /
• 제5권2호
• /
• pp.39-44
• /
• 2006

The dissolution amount of Zn plate was $0.058mg/cm^2$ in the non-magnetically treated solution, and was $0.059mg/cm^2$ in the magnetically treated solution after 24 hours of immersion. The magnetic treatment had no effect to corrosion of Zn plate as pH on surface was not recognized the difference. The addition of Zn(II) ion in the solution was prepared to the effects of corrosion and dissolution of Fe. The regularity was not obtained the effect of the magnetic treatment on the dissolution of Fe plate.

• 한국동물위생학회지
• /
• 제32권4호
• /
• pp.347-351
• /
• 2009

Bruella spp. involves a considerable danger of public health and farm animal industry. In this study, we assessed the disinfection efficacy of alkaline disinfectant solution and three commercial farm disinfectants (quaternary ammonium compound, sodium dichloroisocyanurate, potassium monopersulphate/sodium dichloroisocyanurate) against Brucella ovis. A bactericidal efficacy test by broth dilution method was used to determine the lowest effective dilution of selected disinfectants following exposure to test bacteria for 30 minutes at $4^{\circ}C$. Disinfectants and test bacteria are diluted with distilled water (DW), hard water (HW) or organic matter suspension (OM) according to treatment condition. Three commercial disinfectant showed excellent antimicrobial activity (up to dilution of $\times200$ in OM treatment). Alkaline disinfectant solution demonstrated favorable bactericidal efficacy against B. abortus (at dilution of $\times20$ in OM treatment). Three commercial farm disinfectants possess excellent efficacy against B. ovis. Alkaline disinfectant solution has lower potency than commercial farm disinfectant but could help to limit the spread of brucellosis.

• Biotechnology and Bioprocess Engineering:BBE
• /
• 제5권1호
• /
• pp.65-70
• /
• 2000

An approximated analytical solution of mathematical model for the three phase fluidized bed bioreactor (TFBBR) was proposed using the linearization technique to describe oxygen utilization rate in wastewater treatment. The validation of the model was done in comparison with the experimental results. Satisfactory agreement was obtained in the comparison of approximated analytical solution and numerical solution in the oxygen concentration profile of a TFBBR. The approximated solutions for three modes of the liquid phase flow were compared. The proposed model was able to predict the biomass concentration, dissolved oxygen concentration the height of efficient column, and the removal efficiency.

• 한국주조공학회지
• /
• 제38권1호
• /
• pp.1-8
• /
• 2018

In this study, we focused on the correlation between the solidification structure, heat treatment and mechanical properties of the A356 alloy according to the conditions of Sr modification. The microstructural evolution of the eutectic Si and ${\alpha}-Al$ phase in the A356 alloy castings depending on the amount of Sr were investigated during solid solution heat treatment using an optical microscope, a scanning electron microscope and an image analyzer. In addition, tensile tests on the heat treated materials examined the relationship between the microstructure and the fracture surface. The as-cast A356 alloys under 40 ppm Sr showed an undermodified microstructure, but that of the added 60-80 ppm Sr had well modified structure of fine fibrous silicon. After solid solution treatment, the microstructure of the undermodified A356 alloy exhibited a partially spheroidized morphology, but the remainder showed the fragmentation of fibrous shaped silicon. The spheroidization of the eutectic silicon in the modified A356 alloys was completed during heat treatment, which was very effective in increasing the elongation. This is supported by the fracture surface in the tensile test.

• 열처리공학회지
• /
• 제28권5호
• /
• pp.229-238
• /
• 2015

The effects of Sn addition and solution treatment on corrosion behavior were studied in AZ91 magnesium casting alloy. The addition of 5%Sn contributed to the introduction of $Mg_2Sn$ phase, to the reduction in dendritic cell size and to the increase in the amount of secondary phases. After the solution treatment, trace amount of $Al_8Mn_5$ particles were observed in the ${\alpha}$-(Mg) matrix for the AZ91 alloy, while $Mg_2Sn$ phase with high thermal stability was additionally found in the AZ91-5%Sn alloy. Before the solution treatment, the AZ91-5%Sn alloy had better corrosion resistance than the Sn-free alloy, which is caused by the enhanced barrier effect of the (${\beta}+Mg_2Sn$) phases formed more continuously along the dendritic cell boundaries. It is interesting to note that after the solution treatment, the corrosion rate of both alloys became increased, but the Sn-added alloy showed higher corrosion rate than the Sn-free alloy. The microstructural examination on the corroded surfaces revealed that the remaining $Mg_2Sn$ particles in the solution-treated AZ91-5%Sn alloy play a role in accelerating corrosion by galvanic coupling with the ${\alpha}$-(Mg) matrix.

• 한국작물학회:학술대회논문집
• /
• 한국작물학회 2017년도 9th Asian Crop Science Association conference
• /
• pp.217-217
• /
• 2017

Seed priming leading to improved emergences, germination speed and uniformity under unfavorable conditions without loss of longevity are the best level of techniques. We studied the possibility to obtain primed seed with reduced mean germination time (MGT) and uniformity but with simple, fast and effective methods. The experiments were carried out at $15^{\circ}C$ for 16 hours with priming treatment. To compare the effects of each treatment, we used 200mM $CaCl_2$ priming or hydro priming or no imbibition after ultrasonication or red light treatment. The light treatment was performed by irradiating 2000 lux of red light for 15, 30, 60, and 120 minutes. Addition, in order to investigate the effect of the priming solution, treated at 200mM $CaCl_2$ for 8 hours. Ultrasonication treatment was performed for 5, 10, and 20 minutes at exposures of 13.0, 17.3, and 21.6 kHz during priming. For liquid smoke (LS) treatment, seed soaked in 0%, 0.5%, 1.0%, 5.0% and 10.0% of diluted water and 200mM $CaCl_2$ solution. After each treatment, the seeds were dried to moisture content ranged 5-8% at $25^{\circ}C$ for 24 hours. The effect of seed treatment was evaluated with germination percentage (GP), MGT, germination index(GI), germination rate(GR), Germination Uniformity(GU) and heath seed percentage(HS). For several factors tested, we found that the desired germination improvement could be obtained by treating the seed with ultrasonication at 17.3 kHz for 5 minutes in water or red light exposure at 2000 lux for 120 min in water that resulted very similar to those used to 200mM $CaCl_2$ priming for 16 hrs. However, LS treatment showed no improvement in all diluted solution. Therefore, the methods applied ultrasonication and red light treatment showed high potential for fast and easy treatment avoiding pollution of salt solution waste.

• Journal of Advanced Marine Engineering and Technology
• /
• 제24권6호
• /
• pp.70-77
• /
• 2000

In this paper, the effect of solution and age heat treatment to the corrosion behavior for the Ti-6Al-4V alloy were studied by cyclic polarization methods. Ti-6Al-4V was solution heat treated at $1,066^{\circ}C$ and $966^{\circ}C$ for 5 hours, and followed by age heat treated at $650^{\circ}C$, $600^{\circ}C$ and $550^{\circ}C$ with 1, 2, 4, 8 and 16 hours under vacuum environment. Test solution was 3.5% NaCl with temperature $25^{\circ}C$. The obtained results were as follows: 1. Base metal was exhibited higher electrical charge than that of solution and aged material. With decrease of solution-treatment temperature from 1066 to $966^{\circ}C$, the electrical charge was increased due to softening of micro structure. 2. The corrosion resistance of specimen that solution treated at $966^{\circ}C$ for 5 hours and age heat treated at 650, 660 and $550^{\circ}C$ were increased with increase of aging time to 4, 8 and 16 hours respectively, and then decreased. 3. In case of 316L stainless steel, measured charge and corrosion potential was 0.0627 coulomb and -614 mV respectively. Corrosion resistance of Ti-6Al-4V was higher than that of 316L.

• 한국주조공학회지
• /
• 제38권2호
• /
• pp.32-40
• /
• 2018

Changes in the microstructures and mechanical properties of an AC2B alloy through solution heat treatment were investigated using recycled AC2B cutting chips as raw material. The as-cast microstructure of the AC2B alloy comprised ${\alpha}$-Al, $Al_2Cu$, and coarse needle-shaped phases considered to be eutectic Si and an Al-Fe-Si based intermetallic compound. After solution heat treatments at $505^{\circ}C$ for 1 h and 6 h, the samples showed complete dissolution of $Al_2Cu$ and relatively fine distribution of intermetallic compounds. Hardness test results showed that the hardness rapidly increased after the solution heat treatment for 1 h by solid solution hardening, and the increase of hardness exhibited a plateau from 1 h to 6 h. The results of the hardness and tensile tests showed that there was no visible difference in the effect of 1 h and 6 h solid solution treatment.

• 대한한의학회지
• /
• 제18권1호
• /
• pp.218-237
• /
• 1997

In order to investigate the antihypertentive effects and its mechanism of the Siegesbeckia pubescens aqua-acupuncture treatment, experiments were performed on immediate and continuous antihypertensive effects, vasodilatation-autonomic nerve block, diuretic activity, and angiotensin converting enzyme inhibitory activity. The results were as follows; 1. Acupuncture treatment group showed significantly immediate antihypertensive effects in 4 hours after treatment. Normal saline aqua-acupuncture treatment group showed significantly immediate antihypertensive effects in 2, 4 and 6 hours after treatment. Siegesbeckia pubescens aqua-acupuncture treatment group showed significantly immediate antihypertensive effects in 30 minutes, 1, 2, 4 and 6 hours after treatment. 2. Siegesbeckia pubescens aqua-acupuncture treatment group showed significantly continuous antihypertensive effects in 6, 8, 9 and 10 days after treatment. 3. Siegesbeckia pubescens aqua-acupuncture extract solution showed significantly vasodilatatory and sympathetic nerve block effects with concentration of $10^{-6},\;10^{-5},\;10^{-4},\;10^{-3}g/m{\ell}$. 4. Oral administration group of the Siegesbeckia pubescens aqua-acupuncture extract solution didn't show no significantly diuretic effects. 5. Siegesbeckia pubescens aqua-acupuncture extract solution showed 28.8% angiotensin converting enzyme inhibitory activity.

• Journal of Plant Biotechnology
• /
• 제48권2호
• /
• pp.77-85
• /
• 2021

수경재배는 토양 없이 물로만 재배 가능하며 날씨의 영향을 받지 않아 기존에 토양을 이용해 재배하는 것에 비해 많은 이점을 지니고 있다. 여기에 물 대신 배양액을 추가한다면 생육을 더욱 앞당길 수 있다. 본 연구는 배양액과 인공광 처리에 따른 새싹보리의 성장과 이화학적 특성을 조사하였다. 먼저 배양 기간이 지남에 따라 식물체의 길이는 커졌으며 LED 처리구의 배양액 투입구에서 생장이 빨랐다. 생체량 및 건조량은 형광등 처리구가 LED 처리구보다 더 무거웠다. 새싹보리 분말의 색상은 약간의 차이를 보였으며, L값은 50.79~53.77, a 값은 -6.70 ~ -4.42, b 값은 13.35 ~ 14.76이었으며 L값과 b 값은 LED 처리구가 높았으나 a 값은 형광등 처리구가 상대적으로 높았다. 총페놀 함량은 두 처리구에서 대조구가 배양액 투입구보다 높았으나, 총플라보노이드 함량은 총페놀과는 반대 현상을 보였다. TEAC의 경우 대조구의 항산화능력이 배양액 투입구보다 높았으며 FRAP의 경우 형광등 처리구가 LED 처리구보다 높은 함량을 나타내었다. 총 구성아미노산 함량은 106.82 ~ 122.63 mg/g dry powder였으며, 필수아미노산 함량은 47.01 ~ 56.19 mg/g dry powder였고 비필수아미노산은 67.86 ~ 77.66 mg/g dry powder 범위였다. 구성아미노산 중 가장 많이 검출된 것은 Asp이며, Glu, Ala, Leu, Val 순으로 나타났다.