• Journal of the Korean Home Economics Association
• /
• v.8 no.1
• /
• pp.87-92
• /
• 1970

Recently it has become a common belief that ascorbic acid comes to break up in the process of making its color after peeling it. In this study the writer has attempted to observe whethier ascorbc acid really breaks up or not, what percentage of salt is needed in water to keep ascorbic acid in the best condition. Ascorbic acid was quantified by the spectrophotometric method. The results were obtained as follows; It seems that ascorbic acid does not break up considerably in mixing by the imxer for two minutes and if the mixing lasts longer ascorbic acid breaks up by heat and presumably by enzyme and oxidation. Generally at our home the breaking of ascorbic acid usually does not appear so much as only two minutes, mixing gives us the desirable result.

• Journal of Korean Society of Water and Wastewater
• /
• v.7 no.1
• /
• pp.29-36
• /
• 1993

The complex nature of low flow mixing in natural channels has been investigated using both laboratory experiments and the numerical solution of a proposed mathematical model that is based on a set of mass balance equations describing the mixing and mass exchange mechanisms. Laboratory experiments, which involved collection of channel geometry, hydraulic, and dye dispersion test data, were conducted in a model of four pool and riffle sequences in a 49-m long tilting flume. The experimental results show that flow over the model pool-riffle sequences is highly non-uniform. Concentration-time curves are significantly skewed with long tails. Comparison between measured and predicted concentration-time curves shows good agreement in the general shape, peak concentration and time to peak. The proposed model shows significant improvement over the conventional one-dimensional dispersion model in predicting natural mixing processes in open channels under low flow conditions through pools and riffles.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 1999.10a
• /
• pp.197-203
• /
• 1999

Stainless steels in general has passive film having strong corrosion resistance on surface. Therefore it must be necessarily removed by etching in mixing solution of sulfuric and chloric acid before Nitriding treatment. But in the ion nitriding, nitride layer was easily formed because passive film was removed without difficult by sputtering effect. The removal extent of these passive films was greatly effected by gas mixing ratios and pressure and holding times of pre sputtering factors in pre sputtering stage. As a results of experiment it has been known that pre sputtering pressure and holding time was not nearly effective on the formation behavior of nitride layer. But when A/H2 gas mixing ratios was 1/2 (vol%) was the most effective of the all pre sputtering conditions. It was resulted from the combination of mechanical reaction byArgon bombardment and chemical reaction by reduction of hydrogen on the passive film.

• Nuclear Engineering and Technology
• /
• v.29 no.1
• /
• pp.58-67
• /
• 1997

A numerical study has been peformed to investigate the flow and mixing characteristics of a chemical injection tank in the chemical and volume control system (CVCS) of Yonggwang 5&6 (YGN 5&6). This study was undertaken to provide a basis for modification of the previous design (YGN 3&4) which gave a lot of difficulties in installation and operation of the chemical injection system during the start-up test because it needs a special reciprocating pump with a high actual head. For the tank of length-to-diameter ratios (L/D) of 1,2 and 3, each with and without a baffle inside, calculation results were obtained by solving the unsteady laminar two-dimensional elliptic forms of governing equations for the mass, momentum and species concentration. Finite-difference method was used to obtain discretized equations, and the SIMPLER solution algorithm, which was developed based on the staggered grid control volume, was employed for the calculation procedure. Results showed that the baffle is very effective in enhancing the mixing in the tank and that a baffle should be installed near the tank entrance in order to 110 chemicals into the reactor coolant system (RCS) within the operating time required.

• Elastomers and Composites
• /
• v.48 no.2
• /
• pp.103-113
• /
• 2013

The properties of the rubber composites containing a silane and silica were evaluated by changing the mixing time and temperature, in order to find the optimum mixing conditions. Characteristics of the compounds were evaluated after mixing at $120^{\circ}C$, $140^{\circ}C$, and $160^{\circ}C$ with various mixing time. With increasing of mixing time, mooney viscosity decreased while the bound rubber contents of the compounds increased. Viscosity rise by increased mixing time was bigger at low temperature and the higher the mixing temperature the faster in the formation of bound rubber. With lower mixing temperature of $120^{\circ}C$, cross-linking rate was almost constant. Dynamic viscoelastic properties and dispersity of the compound showed that dispersion of ingredients and reaction was not sufficient with the mixing time of less than 10min. On the contrary, with high temperature, it was obvious that good dynamic and physical properties could be obtained due to sufficient coupling reaction, however it was thought this high temperature is not optimum because of sensitive cross-linking rate and physical properties and excessive formation of bound rubber. Consequently, it was confirmed that the mixing condition of 10min at $140^{\circ}C$ was optimum for the silane coupling reaction and dispersion of functionalized S-SBR containing silica and silane.

• Elastomers and Composites
• /
• v.51 no.2
• /
• pp.81-92
• /
• 2016

1,3-Diphenylguanidine (DPG) is commonly used as a secondary accelerator which not only acts as booster of cure but also activating silanization reaction. The aim of this study is to increase the interaction between silica and rubber by using DPG. In this study, mixing was proceeded in two steps. The T-1 compound is mixed DPG with silica and silane coupling agent in the kneader at high temperature which is named as $1^{st}$ mixing step. T-3 compound is mixed DPG with curatives in the two-roll mill at low temperature which is named as $2^{nd}$ mixing step. The T-2 compound is mixed a half of DPG in $1^{st}$ mixing step and the remainder is mixed in $2^{nd}$ mixing step. Total DPG content was equal for all compounds. When DPG is mixed with silica, silane coupling agent during the $1^{st}$ mixing step, a decrease in cure rate and an increase in scorch time can be seen. This indicates that DPG is adsorbed on the surface of silica. during rubber processing. However, bound rubber content is increased and dynamic properties are improved. These results are due to the highly accelerated silanization reaction. However, there are no significant difference in 100%, 300% modulus.

• The Korean Journal of Ceramics
• /
• v.1 no.3
• /
• pp.131-136
• /
• 1995

It has been reported that the biocement obtained by mixing $CaO-SiO_2-P_2O_5$ glass powders with ammonium phosphate solution has biocompatibility as will as high strength. The hardening mechanism and hydroxyapatite forming mechanism were discussed when $53.6%CaO_1,\; 38.1%SiO_2,\; 7.7P_2O_6,\; 0.6%CaF_2$(mole %) glass powder was reacted with ammonium phosphate solution and reacted in tris-buffer solution, respectively. High strength hardened biocement was obtained for the specimen with $CaNH_4PO_4\;H_2O$ crystal when the glass powder was mixed with ammonium phosphate solution, and hydroxyapatite crystal was rapidly formed only in the sample with $CaNH_4PO_4\;H_2O$ crystal when it was reacted in tris-buffer solution.

• Applied Chemistry for Engineering
• /
• v.33 no.2
• /
• pp.229-233
• /
• 2022

In this study, a gas-liquid hybrid atmospheric pressure plasma reactor of the dielectric barrier discharge method was fabricated and characterized. The solubility of copper oxide in the organic acid solution was increased when argon having a larger atomic weight than helium was used during plasma discharge. There was no significant effect of mixing organic acid solutions under plasma discharge treatment on the variation of copper oxide's solubility. As the applied voltage for plasma discharge and the concentration of the organic acid solution increased, the dissolution and removal power of the copper oxide layer increased. Solubility of copper oxide was more affected by the concentration in organic acid solution rather than the variation of plasma applied voltage. The usefulness of hybrid plasma reactor for the surface cleaning process was confirmed.

• 한국연소학회:학술대회논문집
• /
• 1997.06a
• /
• pp.113-122
• /
• 1997

The conditional moment closure formulation considering the molecular and turbulent diffusion is derived. A simplified solution procedure is proposed to reduce the computational burden due to the increased dimensionality of the conditionally averaged variables. A conditionally averaged variable is expressed as a linear weighted average of the two extremes, 'no reaction' and 'equilibrium' states. The modified elliptic-type conditional moment closure formulation is implemented to simulate a two dimensional nonpremixed mixing layer reacting flow. Results show good agreement for the conditional averages of the species concentration in Bilger et al.

• Journal of Korean Port Research
• /
• v.14 no.2
• /
• pp.241-249
• /
• 2000

The amount of municipal water has been increased rapidly up to now and it is necessary to treat and dispose the wastewater effectively. The recent trend of the effluent disposal system, after treatment, show a nearshore discharge which has an outfall with length somewhere between the shoreline discharge and an extended deepwater outfall. There is no universal solution to municipal water treatment and disposal and each case must be examined on its merits and on economic, technical and environmental bases. In this study we focused mostly on the scientific and engineering aspects of ocean disposal through the outfall. For this purpose, we made an investigation to the near-field characteristics of discharged water and made some comparison with the existing experimental results. We also applied it to the Pusan Jungang Effluent Outfall System, which is planned to build in the Gamchun harbour and will be completed in 2011. The model output showed the trajectoral variation of dilution and mixing behavior for three cases of outfall system. Dilution differences have been simulated and found the highest dilution condition under the different displacement of outfall system. On the basis of these outputs it will be proposed the optimum outfall system type and location.