• Journal of Conservation Science
• /
• v.33 no.6
• /
• pp.485-495
• /
• 2017

The purpose of this study is to evaluate the functionality and lightfastness of the natural pigments according to the type of Seokganju used as Dancheong. The commercially available red iron-oxide-based natural pigments that are called Seokganju and Daija manufactured by traditional methods in Korea and Japan were selected. The analysis of the constituent minerals and constituents of 8 kinds of collected Seokganju showed that most of them contained hematite. There are two types of Seokganju according to the $Fe_2O_3$ contents. The type of Seokganju can be characterized not only using the main component but also from the burn-out processing. The chromaticity results for Seokganju with a high $Fe_2O_3$ concentration indicate dark red or grayish brown, while those for Seokganju with a low $Fe_2O_3$ concentration indicate yellowish red or yellowish brown. Samples were prepared by mixing with a glue solution and functional properties were evaluated based on the opacity and spreadability. Coated samples were used in the lightfastness test. The spreadability and opacity of the pigments were measured differently depending on the main component. Most Seokganju samples a showed slight color change until $9,000kJ/m^2$ but rapid color changes were detected after $18,000kJ/m^2$. In particular, burnt Seokganju showed superior lightfastness.

• Journal of Korean Society of Environmental Engineers
• /
• v.30 no.6
• /
• pp.637-641
• /
• 2008

The aims of this research were to manufacture tailored powder activated carbon having a higher prechlorate removal efficiency and to compare perchlorate removal efficiency with different carbon materials for applying to the drinking water treatment plant. Activated carbon pre-loaded with cetyltrimethylammonium chloride(CTAC) has been researched to be an effective adsorbent for removing perchlorate in the water. 10,000 mg/L tailored powder activated carbon were manufactured by mixing 5.0 g of powder activated carbon(PAC) into 500 mL of 5,000 mg/L CTAC solution. The tailored powder activated carbon had 10 times higher perchlorate removal efficiency than virgin powder activated carbon. The residual perchlorate gradually decreased with the first 15 minute contact time with the tailored powder activated carbon, however, the longer contact time did not affect perchlorate removal. Tailored powder activated carbon by manufactured with 1,083 mg/g iodine value carbon had almost 4 times higher perchlarate removal efficiency than the 944 mg/g iodine value carbon. Dosage of 5 mg/L tailored powder activated carbon, which can adaptable dosage at the treatment plant, could decrease the perchlorate concentration from 50 $\mu$g/L to 15 $\mu$g/L.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.12 no.3
• /
• pp.167-173
• /
• 1979

It is preented the removable moving screen media-activated sludge (REMSMAS) process by using the biological fixed-film systems. The substrate removal kinetic difference between the aeration-only completed mixing activated sludge (CMAS) process and REMSMAS process were observed. The substrate removal kinetics were developed based on the attached and suspended microbial growths. The units of the aeration-only CMAS process were continously operated with the normal detention time of 4.5, 6, 9.5 and 12 flours studies after steady-state condition and the operating of the REMSMAS units conducted with the normal detention time of 6 and 12 hours studies in nonsteady-state condition. The feed solution was diluted 18 times to the raw starch wastewater in of order to maintain the proper COD (950mg/l) and BOD (450mg/l) concentration. Design parameters related to the suspended microbial growths were caculated by the equations used in the aeration-only CMAS model and these parameters used to evalute the kinetic constants in the REMSMAS process. The kinetic constant values of $Y_2,\;K_d,(\mu_{max})_s\;and\;K_s$ from Monod equations were respectively 0.78, 0.027/hr, 1.1/hr and 95mg/l in the aeration-only CMAS process. The value of the aera capacity (F) appeared to be $9.1\;mg/cm^2-day$ and the mean value of the saturation constant $(K_g)$ appeared to be 53.5 mg/l in the REMSMAs process. Also, the substrate removal .ate of the REMSMAS process was higher than that of the normal activated sludge process when this system was operated in steady-state condition. However, the rate was reduced as the critical operating day was approached.

• Journal of the Korean Chemical Society
• /
• v.26 no.5
• /
• pp.265-273
• /
• 1982

The effect of ${\pi}$ bonds on the calculated dipole moments for square planar and tetrahedral [M(II)$O_2S_2$]] type complexes has been investigated by two different approaches. One is the approximate molecular orbital method based on the assumption that the mixing coefficient CM of the valence basis sets for the central metal ion and the appropriate ligand orbitals is equal for all ${\sigma}$ and ${\pi}$ bonding molecular orbitals. The other is the more refined calculation based on the semiempirical LCAO-MO method. If ${\sigma}$ bonds only are assumed to be formed, the calculated dipole moments for square planar and tetrahedral complexes are lower than those of the experimental values. If the contribution of ${\pi}$ bonds to the calculated dipole moments are fully considered, the calculated dipole moments for both square planar and tetrahedral [M(II)$O_2S_2$]] type complexes are higher than the experimental values. However if ${\pi}$ bonds are assumed to be delocalzed, the calculated dipole moments for tetrahedral [M(II$O_2S_2$]] type complexes fall in the range of the experimental values, but those for square planar complexes deviate from the experimental values. These results suggest that [M(II)$O_2S_2$]] type complexes may have the tetrahedral structure in inert solvent solution. This structure is in agreement with the experimental one. The calculated dipole moments for tetrahedral [M(II)$O_2S_2$]] type complexes indicate that the contribution of ${\pi}$ bonds to the calculated dipole moments may not be neglected.

• Applied Chemistry for Engineering
• /
• v.8 no.1
• /
• pp.99-107
• /
• 1997

This study Provides the treatment methods of liquid wastes from the dissolution/purification process of nuclear fuel raw material and the fabrication process of nuclear fuel powder. One of the treatment methods is to process liquid waste from uranium raw material dissolution/purification process. This waste, of the strong acid, can be reused to dissolve the fine ADU particles in filtrate which is ADU waste of pH 8.0 converted from AUC waste after recovery of uranium. To dissolve the fine ADU particles, ADU filtrate was pretreated to pH 4.0 with the dissolution/purification waste, and then mixed with the lime to pH 9.2 and aged for 30 minutes. From this processing, uranium content of the filtrate was decreased to below 3ppm. The waste from fuel powder fabrication is emulsified solution dispersed with fine oil droplets. This emulsion was destroyed effectively by adding and mixing the nitric acid with rapid heating at the same time. After this processing, $Na_2U_2O_7$ compound is produced by addition of NaOH. Optimum condition of this processing was shown at pH 11.5, and uranium content of the filtrate was analyzed to 5ppm. To remove the trace of uranium in the filtrate, lime should be added. Otherwise, 4N nitric acid was used to destroy the emulsion directly, and then lime was added to this waste. Uranium content of the treated filtrate was below 1 ppm. In addition to these wastes, the trace of uranium in filtrate after recovery of uranium from the AUC waste which is produced during PWR power preparation, is treated with NaOH to takeup fluorine(F) in the waste because fluorine is valuable and toxic material. In the finally treated waste, uranium was not detected.

• Journal of the Korean Ceramic Society
• /
• v.41 no.4
• /
• pp.284-288
• /
• 2004

To improve mechanical properties of $Al_2$O$_3$/ZrO$_2$composites have been controlled dispersion of ultra low size ZrO$_2$ particles in $Al_2$O$_3$ ceramics by polymeric precursor method (Pechini process). In case of coprecipitation or mechanical mixing of ZrO$_2$ powders with $Al_2$O$_3$, homogeneous dispersion and controlling the ZrO$_2$ size were relatively difficult due to high sintering temperature. So the polyesterization process of Zr/Y(NO$_3$)$_3$-citric acid solution in ethylene glycol with the commercial sub-micron sized o(-alumina powder (Sumitomo AES-11(0.4 ${\mu}{\textrm}{m}$)) was adopted in order to obtain homogeneous dispersion of ZrO$_2$ in A1203. By this partial polyesterization process, the homogeneous dispersion of relatively low sized ZrO$_2$in $Al_2$O$_3$/ZrO$_2$composites was achieved at 1450∼1$600^{\circ}C$ of sintering temperature range and their mechanical properties were measured.

• Journal of the Korean Institute of Intelligent Systems
• /
• v.13 no.2
• /
• pp.200-208
• /
• 2003

This paper proposes a separation and feature extraction of image signals using the independent component analysis(ICA) based on neural networks of efficient learning rule. The proposed learning rule is a hybrid fixed-point(FP) algorithm based on secant method and momentum. Secant method is applied to improve the performance by simplifying the 1st-order derivative computation for optimizing the objective function, which is to minimize the mutual informations of the independent components. The momentum is applied for high-speed convergence by restraining the oscillation in the process of converging to the optimal solution. The proposed algorithm has been applied to the composite images generated by random mixing matrix from the 10 images of $512\times512$-pixel. The simulation results show that the proposed algorithm has better performances of the separation speed and rate than those using the FP algorithm based on Newton and secant method. The proposed algorithm has been also applied to extract the features using a 3 set of 10,000 image patches from the 10 fingerprints of $256\times256$-pixel and the front and the rear paper money of $480\times225$-pixel, respectively, The simulation results show that the proposed algorithm has also better extraction speed than those using the another methods. Especially, the 160 basis vectors(features) of $16\times16$-pixel show the local features which have the characteristics of spatial frequency and oriented edges in the images.

• Journal of the Korean Ceramic Society
• /
• v.34 no.2
• /
• pp.115-122
• /
• 1997

The powder preparation by using emulsion drying method, one of the chemical powder fabrication methods has the advantages; easy to control the chemical stoichiometry and to fabricate homogeneously fine particles. In the present study, the initial morphology and size distribution of the powder fabricated by using emulsion dry-ing method were controlled and were improved the homogeneity. By carefully controlling the mixing ratio of oil phase and aqueous solution and surfactant of preventing emulsion separation, the Bi(Pb)-Sr-Ca-Cu-O su-perconducting powders were prepared. The properties of the superconducting powder fabricated by this method and the microstructures and superconducting properties of the pelletized samples were investigated. The microstructures and electric properties of the tapes prepared by oxide powder-in-tube method were in-vestigated. The fabricated powder was spherical with less than 1$\mu$m but most of them was agglomerated with 2~5$\mu$m in size. The critical temperature of the pelletized sample annealed at 84$0^{\circ}C$ for 72 hours in oxygen par-tial pressure of 1/13atm in Ar atmosphere was 108K. And the critical current of the first and second annealed tapes in air prepared by oxide powder-in-tube process were 0.4A and 1.5A, respectively.

• Journal of the Korean Electrochemical Society
• /
• v.19 no.1
• /
• pp.21-27
• /
• 2016

Vanadium redox flow batteries (VRFBs) using the electrolytes containing various vanadium ions in sulfuric acid as supporting solution are one of the energy storage devices in alternatively charging and discharging operation modes. The positive electrolyte contains $V^{5+}/V^{4+}$ and the negative electrolyte $V^{2+}/V^{3+}$ depending on the operation mode. To prevent the mixing of two solutions, proton exchange membranes are mainly used in VRFBs. Nafion 117 could be the most promising candidate due to the strong oxidative property of $V^{5+}$ ion, but causes high crossover of electroactive species to result in a decrease in coulombic efficiency. In this study, the composite membranes using Nafion ionomer and porous polyethylene substrate were prepared to keep good chemical stability and to decrease the cost of membranes, and were compared to the properties and performance of the commercially available electrolyte membrane, Nafion 117. As a result, the water uptake and ionic conductivity of the composite membranes increased as the thickness of the composite membranes increased, but those of Nafion 117 slightly decreased. The permeability of vanadium ions for the composite membranes significantly decreased compared to that for Nafion 117. In a single cell test for the composite membranes, the voltage efficiency decreased and the coulombic efficiency increased, finally resulting in the similar energy efficiency. In conclusion, the less cost of the composite membranes by decreasing 6.4 wt.% of the amount of perfluorinated sulfonic acid polymer due to the introduction of porous substrate and lower vanadium ion permeability to decrease self-discharge were achieved than Nafion 117.

• Journal of the Korean Electrochemical Society
• /
• v.10 no.3
• /
• pp.184-189
• /
• 2007

The importance of secondary battery industry is getting excited according to the development of battery industry as a high efficiency energy supplier of electronic machine of mobile information such as mobile phone, lap-top computer, PDA. It is rasing the interest about security of safety and high efficiency of cathode material for main part of secondary lithium battery. The cathode material which has been used like $LiCoO_2,\;LiMn_2O_4,\;LiNi_xCo_yMn_zO_2,\;LiNi_xCo_yM_zO_2$ (M=Al, Zr, Mg etc.,) the most typical material is $LiCoO_2$. But it is studying the development of substitute such as efficiency amelioration of $LiCoO_2$, thetiary element, olivine element because of the capacity of $LiCoO_2$, the matter of security; especially the betterment of efficiency, security research of safety has been actively processed in domestic and overseas about surface coating treatment of active cathode which is using oxide ($M_xO_3$). This study analyses side effect of battery according to increase of surface treatment, formation of precipitation for reagent condensation, non-reagent residue of oxide ($M_xO_3$) which is remains during the surface treatment of $LiCoO_2$; conducts study of new process, the consideration of the electrochemical property to improve oxide solution of mixing rate, mixture of surface treatment, dryness, calcinations conditionetc.