• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2011년도 제37회 추계학술대회논문집
• /
• pp.745-749
• /
• 2011

혼합용 임펠러를 장착한 연료탱크의 액체연료와 미세 고체입자의 부유, 혼합 현상을 분석하고자 2차원 혼합 유동 수치해석을 수행하였다. 다상 유동해석은 Eulerian Grandular Multiphase 기법을 사용하였고, 해석기법을 12vol% 고체 혼합 조건 실험의 축방향 고체 농도 분포와 비교하여 확인하였다. 해석용 연료탱크는 10.5vol% 고체입자를 액체연료와 혼합하는 것으로 회전수 700rpm 조건에서 4가지 경우의 임펠러 위치와 유속 조건으로 해석을 수행하였다. 각 경우에 대한 Quality of Suspension 결과를 비교하여 적합한 임펠러 위치와 속도방향을 확인하였다.

• 대한기계학회논문집B
• /
• 제20권11호
• /
• pp.3655-3665
• /
• 1996

An analytical solution is presented for the conduction-dominated solidification of a binary mixture in a semi-infinite medium. The present approach differs from that of other solution by these four characteristics. (1) Solid fraction is determined from the phase diagram, (2) thermophysical properties in mushy zone are weighted according to the local solid fraction, (3) non-equilibrium solidification can be simulated and (4) the cooling condition of under-eutectic temperature can be simulated. Up to now, almost all analyses are based on the assumption of constant properties in mushy zone and solid fraction linearly with temperature or length. The validation for these assumptions, however, shows that serious error is found except some special cases. The influence of microscopic model on the macroscopic temperature profile is very small and can be ignored. But the solid fraction and average solid concentration which directly influence the quality of materials are drastically changed by the microscopic models. An approximate solution using the method of weighted residuals is also introduced and shows good agreement with the analytical solution. All calculations are performed for NH$_{4}$Cl-H$_{2}$O and Al-Cu system.

• 분석과학
• /
• 제23권3호
• /
• pp.261-268
• /
• 2010

본 연구에서는 최근 제안된 PCBs 함유 고상폐기물 공정시험방법을 토대로 PCBs 함유 변압기에서 90건의 시료를 채취 분석하였으며, 제시한 분석방법의 폐기물 시료에 적정성 여부를 검토하였다. 채취한 변압기 절연유에서의 PCBs 농도범위는 7.6~23.8 mg/L로 나타났으며, 규소강판은 $0.02\sim0.54\;{\mu}g/100cm^2$의 농도범위로 검출되었다. 또한, 구리선 등의 비정형 폐기물은 0.01~0.071 mg/kg의 농도범위로 검출 되었다. 본 연구 결과, 폐기물공정시험방법의 새로운 분석방법과 규제기준은 기존의 용출시험방법으로 고상폐기물을 관리하는 경우에 비해 PCBs 함유 폐기물의 관리가 보다 강화된 것으로 판단된다.

• Journal of the Korean Wood Science and Technology
• /
• 제17권4호
• /
• pp.77-82
• /
• 1989

In this study the oxygen index method was used to compare the duration of flaming and the rate of weight loss at the level of 6 and 9mm panel thicknesses among solid wood, plywood, particleboard, and medium density fiberboard. The obtained results were as follows: 1. In 9mm-thick panels, the combustibility was the largest in lauan solid wood followed by medium density fiberboard. particleboard. and plywood. 2. Medium density fiberboard was burned more easily than plywood in 6mm-thick panels and the higher oxygen concentration was needed as the panel thickness increased. 3. The oxygen indices of 9mm-thick panels were 29.0 in lauan solid wood, 31.4 in medium density fiberboard, 33.0 in particleboard, and 33.4 in plywood and those of 6mm-thick panels were 28.3 in medium density fiberboard and 29.7 in plywood. 4. The rate of weight loss was the largest in lauan solid wood followed by medium density fiberboard, plywood, and particleboard.

• 한국세라믹학회지
• /
• 제37권8호
• /
• pp.817-823
• /
• 2000

A solid-state electrochemicall cell for sensing CO2 gas was fabricated using a solid electrolyte of Li2CO3-Li3PO4-Al2O3 mixture and a reference electrode of LiMn2O4. The e.m.f. (electromotive force) of sensor showed a good accordance with theoretical Nernst slope (n=2) for CO2 gas concentration range of 100-10000 ppm above 35$0^{\circ}C$. The e.m.f. of sensor was constant regardless of oxygen partial pressure at the high temperature above 0.1 atm. It was, however, a little depended on oxygen partial pressure as the pressure decreased below 0.1 atm. The oxygen-dependency of our sensor gradually disappeared as the operating temperature increased. The sensing behavior of our CO2 sensor was affected by the presence of water vapor, but its effect was small comparing with other sensors.

• Nuclear Engineering and Technology
• /
• 제51권7호
• /
• pp.1842-1852
• /
• 2019

The AP1000 reactor coolant pump is a vertical shielded-mixed flow pump, is the most important coolant power supply and energy exchange equipment in nuclear reactor primary circuit system, whose steadystate and transient performance affect the safety of the whole nuclear island. Moreover, safety demonstration of reactor coolant pump is the most important step to judge whether it can be practiced, among which software simulation is the first step of theoretical verification. This paper mainly introduces the fluid-solid coupling simulation method applied to reactor coolant pump, studying the feasibility of simulation results based on workbench fluid-solid coupling technology. The study found that: for the unsteady calculations of the pure liquid media, the average head of the reactor coolant pump with bidirectional fluid-solid coupling decreases to a certain extent. And the coupling result is closer to the real experimental value. The large stress and deformation of rotor under different flow conditions are mainly distributed on impeller and idler, and the stress concentration mainly occurs at the junction of front cover plate and blade outlet. Among the factors that affect the dynamic stress change of rotor, the pressure load takes a dominant position.

• 한국화재소방학회논문지
• /
• 제8권1호
• /
• pp.3-8
• /
• 1994

A new test system was established to measure the flame extinguishing concentration of Halon alternatives. The main characteristic of this system is to use the solid paraffin with a wick instead of liquid fuel, such as n-Heptane. Our results showed that the extinguishing concentration of compounds was lower than that of other existing data, but the trend was consistent with others. The flame extinguishing concentration of all tested compounds were not almost effected by gas flow velocity. The system produces good reliable data with a minimum error for measuring the flame extinguishing concentration. Therefore our new system can be utilized as a standard equipment to evaluate Halon alternatives.

• 한국축산시설환경학회지
• /
• 제8권1호
• /
• pp.9-16
• /
• 2002

본 연구는 경제적이고 효율적으로 돈 슬러리를 분리할 수 있는 새로운 고형물 분리 시스템을 개발하여 최적 시스템의 운행요건을 구명하고 1일 처리용량 200$\ell$ 규모의 pilot에서 분리 시스템의 인자도출 및 분리효율 분석결과는 다음과 같다. 1. 돈 슬러리의 고형물 분리를 위해 간이 저장조와 순환조, 고정식 생물막조로 구성되는 시스템을 개발하여 본시험에 공시하였다. 2. 시스템의 효율을 구명하기 위해서 폭기량과 스크류 배출기의 회전수를 측정한 결과 폭기량은 0.3 l /min에서 Bulking 현상이 거의 나타나지 않았으며 슬럿지 부유현상은 매우 경미하였고 침전효과가 좋았으며 스크류배출기의 회전수는 114ppm에서 고형물 수분 함량이 62%로 수분조절재 없이 축분 퇴비화할 수 있는 조간이 형성되었다. 3. 순환조의 순환 횟수에 따른 오염농도감소는 유입 슬러리의 농도가 낮고 높음에 관계없이 일정한 수준을 감소시켜 주었다. 본 시험에 이용되는 돈 슬러리의 오염농도는 BOD$_{5}$, COD/ sub Mn/, and SS가 각각 15,970($\pm$2,389)mg/l , 20,0040($\pm$5,512)mg/l 및 26,486 ($\pm$5,935)mg/ l 이었으나 순환조의 2회 순환시$BOD_5,\;COD_{Mn}$, and SS 가 각각 5,630mg/l, 5,260mg/l 및 1,250mg/l으로 감소되었다. 4. 따라서, 이 시스템을 돈 슬러리 정화의 전처리시스템으로 적용함으로서 고형물은 수분조절재가 없이 퇴비화 할 수 있고 돈슬러리를 정화처리시 고농도의 오염물질 때문에 처리효율이 떨어지는 활성오니법의 단점을 보완케 함으로서 활성오니 법을 이용한 정화 효율을 크게 높일 수 있을 것으로 사료된다.관찰되었다.3시간 SO$_2$폭로군에서 대조군에 비해 많이 증가하였고 그외의 실험군에서는 대조군에 비해 대부분의 세포에서 감소하거나 소실되었으며 대조군에서 나타나지 않던 점액화된 상피세포들은 모두 SO$_2$폭로군에서 중섬점액질만을 함유하고 있었으며 100 ppm 및 200ppm SO$_2$폭로군에서 그 양이 감소하는 경향을 나타내었다. 산성점액질의 양은 10 ppm 및 50ppm 3시간 SO$_2$폭로군에서는 대조군에 비하여 많이 증가하였으나. 그외 대부분의 SO$_2$폭로군에서는 현전히 감소하거나 소실되었다. 대조군에 비해 SO$_2$폭로군에서 강 sulfomucin은 감소하는경향을 나타내었고, 100 ppm및 200 ppm SO$_2$폭로군에서 강 sulfomucin은 소실되었으나 sialomucin은 대조군에 비해 증가하는경향을 보였다. 하비중격선의 중성점액질은 양은 대조군에 비해 SO$_2$폭로군에서 감소하는 경향을 나타내었으며 100ppm및 200ppm SO$_2$ 폭로군에서 그 감소가 아주 현저하게 대부분의 선포들에서 중성 점액질이 소실되었다. 이상의 결과로 보아 SO$_2$는 비강에 심대한 병리조직학적 변화뿐만 아니라 점액질 대사에 심대한 영향을 미쳐 심한 병변을 야기시킴을 알수 있었다. 전반적으로 SO$_2$의호흡기 영향은 고농도로 갈수록 심한 영향을 미쳤으며 저 농도 에서도 폭로시간이 길어짐에 따라 나타나는 SO$_2$의영향이 고농도와 유사한경향을 나타내며 또한 모든 SO$_2$의 농도를 비교해보면 폭로 시간이 길어질수록 그영향이 더 심하게 나타났다.ate to harvest

• 한국환경보건학회지
• /
• 제40권2호
• /
• pp.137-146
• /
• 2014

Objectives: Feasibility of electrochemical oxidation of the aqueous non-biodegradable wastewater such as cationic dye Rhodamine B (RhB) has been investigated in an electrochemical reactor with solid polymer electrolyte (SPE). Methods: Nafion 117 cationic exchange membrane as SPE has been used. Anode/Nafion/cathode sandwiches were constructed by sandwiching Nafion between two dimensionally stable anodes (JP202 electrode). Experiments were conducted to examine the effects of applied current (0.5~2.0 A), supporting electrolyte type (0.2 N NaCl, $Na_2SO_4$, and 1.0 g/L NaCl), initial RhB concentration (2.5~30.0 mg/L) on RhB and COD degradation and $UV_{254}$ absorbance. Results: Experimental results showed that an increase of applied current in electrolysis reaction with solid polymer electrolyte has resulted in the increase of RhB and $UV_{254}$ degradation. Performance for RhB degradation by electrolyte type was best with NaCl 0.2 N followed by SPE, and $Na_2SO_4$. However, the decrease of $UV_{254}$ absorbance of RhB was different from RhB degradation: SPE > NaCl 0.2 N > $Na_2SO_4$. RhB and $UV_{254}$ absorbance decreased linearly with time regardless of the initial concentration. The initial RhB and COD degradation in electrolysis reaction using SPE showed a pseudo-first order kinetics and rate constants were 0.0617 ($R^2=0.9843$) and 0.0216 ($R^2=0.9776$), respectively. Conclusions: Degradation of RhB in the electrochemical reactor with SPE can be achieved applying electrochemical oxidation. Supporting electrolyte has no positive effect on the final $UV_{254}$ absorbance and COD degradation. Mineralization of COD may take a relatively longer time than that of the RhB degradation.

• 한국해양공학회지
• /
• 제25권5호
• /
• pp.15-20
• /
• 2011

This study carried out a series of experiments involving impact tests (Drop Weight type & Charpy type with a standard specimen and newly designed I-type specimen), hardness tests, and fracture surface observations of French-made roll shell steel (F), abnormal roll shell steel (M), reheated roll shell steel (R), and S25C steel under heat treatment conditiAn experimental study was carried out to study the solid-liquid mixture upward hydraulic transport of solid particles in vertical and inclined annuli with a rotating inner cylinder. The lift forces acting on a fluidized particle play a central role in many important applications such as the removal of drill cuttings in horizontal drill holes, sand transport in fractured reservoirs, sediment transport, the cleaning of particles from surfaces, etc. In this study a clear acrylic pipe was used to observe the movement of solid particles. Annular velocities varied from 0.4 to 1.2 m/s. The effect of the annulus inclination and drill pipe rotation on the carrying capacity of a drilling fluid, particle rising velocity, and pressure drop in a slim hole annulus were measured for fully-developed flows of water and aqueous solutions of CMC (sodium carboxymethyl cellulose) and bentonite. The rotation of the inner cylinder was efficient at carrying particles to some degree. For a higher particle volume concentration, the hydraulic pressure loss of the mixture flow increased because of the friction between the wall and solids or between solids.