• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.36 no.2
• /
• pp.136-142
• /
• 2023

In the past, the efficiency of solar cells had been increased in order to increase the efficiency of solar modules. However, in recent years, in order to increase output in the solar industry and market, the competitiveness of solar cells based on large-area solar cells and multi-bus bar has been increasing. Multi-busbar solar module is a technology to reduce power loss by increasing the number and width of the front busbar of the solar cell and reducing the current value delivered by the busbar by half through half-cutting. In the case of the existing M2 (156.75×156.75 mm²) solar cell, even with a half-cut, power loss could be sufficiently reduced, but as the area of the solar cell is enlarged to more than M6 (166×166 mm²), the need for more divisions emerged. This affected not only solar cells but also inverters required for module array configuration. Therefore, in this study, the electrical characteristics of a large-area solar cell and after division were extracted using Griddler simulation. The output characteristics of the module were predicted by applying the solar cell parameters after division to PSPice, and a guideline for the large-area solar module design was presented according to the number of divisions of the large-area solar cell.

• Applied Microscopy
• /
• v.50
• /
• pp.17.1-17.9
• /
• 2020

Recent advances in fabrication have enabled radial-junction architectures for cost-effective and high-performance optoelectronic devices. Unlike a planar PN junction, a radial-junction geometry maximizes the optical interaction in the three-dimensional (3D) structures, while effectively extracting the generated carriers via the conformal PN junction. In this paper, we report characterizations of radial PN junctions that consist of p-type Si micropillars created by deep reactive-ion etching (DRIE) and an n-type layer formed by phosphorus gas diffusion. We use electron-beam induced current (EBIC) microscopy to access the 3D junction profile from the sidewall of the pillars. Our EBIC images reveal uniform PN junctions conformally constructed on the 3D pillar array. Based on Monte-Carlo simulations and EBIC modeling, we estimate local carrier separation/collection efficiency that reflects the quality of the PN junction. We find the EBIC efficiency of the pillar array increases with the incident electron beam energy, consistent with the EBIC behaviors observed in a high-quality planar PN junction. The magnitude of the EBIC efficiency of our pillar array is about 70% at 10 kV, slightly lower than that of the planar device (≈ 81%). We suggest that this reduction could be attributed to the unpassivated pillar surface and the unintended recombination centers in the pillar cores introduced during the DRIE processes. Our results support that the depth-dependent EBIC approach is ideally suitable for evaluating PN junctions formed on micro/nanostructured semiconductors with various geometry.

• Proceedings of the KIEE Conference
• /
• 1996.07a
• /
• pp.540-542
• /
• 1996

A detailed model of a photo voltaic array written in PSPlCE is presented in this paper. It is likely that solar cell arrays in photovoltaic system is shadowed partly by clouds, buildings. By the effects of partial shadowing, not only the output power of solar cell arrays is decreased, but also shadowed cells are reversely biased and damaged in some cases. In this paper, by analyzing the output characteristics of solar cell arrays according to various shadow patterns, we investigate solar cell arrays connection of prevention the shadowing effects to the utmost.

• Proceedings of the KIEE Conference
• /
• 1996.11a
• /
• pp.326-328
• /
• 1996

The 10kW or 1MW model of a photovoltaic array written in PSPICE is presented in this paper. A problem with this large scale centralized photovoltaic system is the decrease of power due to the resistance of cable connecting individual subarray with inverter. In this paper, we analyzed the relationship between the resistance of cable and subarray output power of 1MW photovoltaic system by the PSPICE modeling. As a result of simulation, we can proved that photovoltaic array output power is limitted by the resistance of cable.

• Journal of the Korean Solar Energy Society
• /
• v.30 no.6
• /
• pp.95-101
• /
• 2010

This paper presents performance estimation approach of grid-connected photovoltaic(PV) system to predict energy yield from irradiance to PV system using normalized yield model for changing meteorological conditions. The accuracy and validity of proposed performance estimation method is identified by compared measured with estimated yield using monitored data. These results will indicate that it is useful to estimate various loss factors causing the system performance obstruction and enhance the lifetime yield of PV system.

• Proceedings of the KIEE Conference
• /
• 1994.07a
• /
• pp.310-312
• /
• 1994

A partial shunt regulator (PSR) which is the power regulator of KOREASAT is modeled. The modeling of the PSR consist of solar array, power circuit, controller. and load models. To realize simple structure. a voltage source of the PSR controller is used the output voltage of the PSR. The model of the PSR has very complex structure with two additional coupled feedback loops. The complex model is simplified to a simple meaningful model with only main feedback control loop. The proposed model is compared to a PSR model with DC voltage source at the PSR controller. The proposed PSR model is verified by comparing the model with SPICE simulation for small signal analysis.

• Journal of Electrical Engineering and Technology
• /
• v.11 no.1
• /
• pp.117-124
• /
• 2016

Solar photovoltaic pumping system is one of most important of renewable energy applications especially in rural areas. Besides, the control strategy for standalone solar pumping system based on induction motor and without DC/DC converter has been widely studied and discussed in the literature. This topology is of great concern due its economic issues, especially when a standard frequency converter (SFCs) with scalar control is used instead of a dedicated PV inverter. This paper proposes an external control module to generate SFCs frequency reference in order to ensure both maximum power point tracking (MPPT). We present method of modeling and control of photovoltaic pumping system based centrifugal pump controlled by new improved incremental conductance in order to optimize the price and operation of pumping system this MPPT algorithm have many advantages like can be eliminate proportional integral controller It is a low cost solution since it requires no additional power equipment. The induction motor driven pump that is powered by a solar array is controlled by the indirect field oriented control (IFOC). The effectiveness of the proposed approach is illustrated by simulations carried out under Matlab Software. The experimental results are compared with simulation results.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.5
• /
• pp.723-730
• /
• 2016

Solar cells in a PV module are connected in series and parallel to produce a higher voltage and current. The PV module has performance characteristics depending on solar radiation and temperature. In addition, the PV system causes power loss by special situations, including the shadows of the surrounding environment, such as nearby buildings and trees. In other words, an increase in power loss and a decrease in life cycle can occur because of the partial shadow and hot-spot effect. Therefore, this paper proposes the optimal configuration algorithm of a bypass diode to improve the output of a PV module and one of a PV array to minimize the loss of the PV array. In addition, this paper presents a model of a PV module and PV array based on the PSIM S/W. The simulation results confirmed that the proposed optimal configuration algorithms are useful tools for improving the performance of PV system.

• Proceedings of the KIPE Conference
• /
• 2001.10a
• /
• pp.251-255
• /
• 2001

This paper presents a new zero current switching (ZCS) inverter for grid-connected photovoltaic system. The proposed circuit provides zero current switching condition for all the switches, which reduces switching losses significantly. It is controlled to extract maximum power from the solar array and to provide sinusoidal current into the mains. Analysis, small signal modeling and design procedure are presented. The validity of the proposed system is verified by experimental results from the 1.2kW prototype inverter operating at 40kHz.

• Proceedings of the KIPE Conference
• /
• 2007.07a
• /
• pp.369-371
• /
• 2007

Due to the measurement noise or system noise, the performance of photovoltaic power generation system can be degraded. If this noise is contained in the solar array voltage measurement signal, the correct operation of the maximum power point tracker can not be guaranteed. The application of the extended Kalman filter to the photovoltaic system can obtain enhanced states estimation result. The Kalman filter provides a recursive solution to optimally estimate from random noise signals. Additionally, as a consequence of Kalman filter, the unmeasurable state such as inductor current can be estimated without current sensor. The methods for system modeling and extended Kalman filter design are presented and the experimental results verify the validity of the proposed system.