• 센서학회지
• /
• 제28권5호
• /
• pp.329-333
• /
• 2019

Solution-processed oxide thin-film transistors (TFTs) have garnered great attention, owing to their many advantages, such as low-cost, large area available for fabrication, mechanical flexibility, and optical transparency. Negative bias stress (NBS)-induced instability of sol-gel IGZO TFTs is one of the biggest concerns arising in practical applications. Thus, understanding the bias stress effect on the electrical properties of sol-gel IGZO TFTs and proposing an effective recovery method for negative bias stressed TFTs is required. In this study, we investigated the variation of transfer characteristics and the corresponding electrical parameters of sol-gel IGZO TFTs caused by NBS and positive bias recovery (PBR). Furthermore, we proposed an effective PBR method for the recovery of negative bias stressed sol-gel IGZO TFTs. The threshold voltage and field-effect mobility were affected by NBS and PBR, while current on/off ratio and sub-threshold swing were not significantly affected. The transfer characteristic of negative bias stressed IGZO TFTs increased in the positive direction after applying PBR with a negative drain voltage, compared to PBR with a positive drain voltage or a drain voltage of 0 V. These results are expected to contribute to the reduction of recovery time of negative bias stressed sol-gel IGZO TFTs.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제54권12호
• /
• pp.573-577
• /
• 2005

[$TiO_2$] sol and $SiO_2$ sol were prepared using sol-gel method. As $H_{2}O$/Alkoxide ratios increased, sol had cluster structure and as $H_{2}O$/Alkoxide ratios decreased, sol had linear structure. Gelation time of $TiO_2$ sol was faster than that of $SiO_2$ sol according to the time. In comparison with initial viscosity between $TiO_2$ sol and $SiO_2$ sol, $TiO_2$ sol was highest at $H_{2}O/Ti(OC_{3}H_{7})_{4}=5$, $SiO_2$ sol was almost constant according to $H_{2}O/Si(OC_{2}H_{5})_{4}$ ratios.

• 한국세라믹학회지
• /
• 제34권6호
• /
• pp.611-619
• /
• 1997

Optimal Mullite sol was synthesized by sol-gel process using Aluminium sec-butoxide(ASB), Tetraethoxysilane(TEOS) and then, Mullite films were dip-coated with various holding time in sol bath and heat-treated at 130$0^{\circ}C$ above for crystallization. The thickness of coated film increased linearly with holding time in sol bath and average pore size was controllable within 20~30$\AA$.

• 한국세라믹학회지
• /
• 제32권9호
• /
• pp.995-1002
• /
• 1995

The alumina fiber was obtained by extruding the TEA complexed polymeric sol, synthesized by the alkoxide sol-gel method, through nozzle. The purpose of this study was to investigate the properties of fiber spun by TEA complexed sol. The analysis of sol indicated that TEA was bonded at alkoxide precursor and the optimum molar ratio for spinning was 0.5 mole of TEA, 3 mole of H2O. The cross section of the fiber from circular nozzle was not circular but oval, which indicated that the shape of nozzle did not affect the shape of fiber. The diameter of the fiber was about 100 ${\mu}{\textrm}{m}$ in the state of dried gel fiber, 60${\mu}{\textrm}{m}$ in calcined fiber, and the tensile strength of the fiber calcined at 90$0^{\circ}C$ was 2.1$\times$108 Pa.

• 한국안전학회지
• /
• 제13권1호
• /
• pp.85-91
• /
• 1998

Sol-gel derived silica films were prepared by dip-coating onto polymethylmethacylate with Tetraethoxysilane(TEOS) as starting materials. Film properties such as viscosity and thickness were investigated as a function of dip speed, waterprecursor ratio, sol aging time. IR spectra of the gel films prepared from TEOS at various R are given. At small values of R the absorption peaks assignable to C-H vibration in $-OC_2H_5$ groups are observed around 3000 and 1500-1300 $cm^{-1}$. These bands indicate that the -$-OC_2H_5$ groups are retained in the gel at small values of R because of incomplete hydrolysis of TEOS. Film behaviour was interpreted in terms of the dependence of hydrolysis and condensation rates on the interplay between sol pH and waterprecursor ratio. Film thickness was found to increase by approximately a factor of two as waterprecursor ratio increased from two to six. Film thickness also increased with sol prepolymerization time. Surface quality was correlated with processing conditions.

• 한국세라믹학회지
• /
• 제28권5호
• /
• pp.365-372
• /
• 1991

LAS (lithium aluminosilicate) sol was synthesized using the hydrolysis-condensation reaction of TEOS, chelated Al(OBus)3 and Li-salt with H2O in alcohol (EtOH+2-Propanol) medium. Effects of important reaction parameters on the properties of sol and gel-derived LAS were examined. The crystallization of the sol-gel derived LAS with ${\beta}$-spodumene composition began at ∼600$^{\circ}C$, and a series of polymorphic transformations occurred as temperature was increased to 1100$^{\circ}C$: amorphous LAS\longrightarrowhexagonal LiAl(SiO3)2\longrightarrow${\beta}$-spodumene. Lowering Li content in the gel enhanced densification and retarded the crystallization significantly. Optimum reaction conditions of LAS sol formation for thin coating applications were derived from rheological measurements, and these can be summarized as: H2O/total alkoxides molar ratio=4, pH=∼2.5, and aging time of ∼250h.

• 한국전기전자재료학회논문지
• /
• 제17권9호
• /
• pp.967-972
• /
• 2004

Hardness and surface property of coated gel materials are considerably different according to kinds(particle size/stabilized ion) of colloidal silica(CS), kinds of silanes, content ratio of silane versus CS, and reaction degree in sol solution. We report the properties of sol-gel coating materials in which the factors of reaction are kinds of CS, contents ratio of CS and MTMS, and reaction time of sol. The contact angles of the coated films obtained from the mixed CS system showed a little good relationship with MTMS content increase to those from HSA CS reaction system and the change of contact angle didn't have much effect on reaction time of sol. In the coating films obtained from HSA CS reaction system, the surface was much rough in case of that the content MTMS decreased and the reaction of sol kept long. The surface roughness of films obtained from the mixed CS reaction system showed similar tendency, though its degree was a little different. In synthesis of sol-gel coating materials, we could identify that choice of CS kinds and content ratio of CS and silane were important and it was desirable the reaction time of sol is not long.

• 한국염색가공학회지
• /
• 제6권1호
• /
• pp.49-53
• /
• 1994

The transparent coloration of glasses has been successfully achieved by coated glass surface with squarylium dye by the sol-gel colored coating method. Treatment of sol-gel colored coating layer with HCI(g) greatly decreases the absorbance at λ$_{max}$, that increases exposure to $NH_{3}$(g) and the reversible color-colorless responce was extremely rapid.d.

• 대한치과교정학회지
• /
• 제36권6호
• /
• pp.451-464
• /
• 2006

본 연구는 항 교정장치의 개발에 도움이 되고자 이산화티탄 광촉매의 코팅 시 안정적이고 효과적인 방법을 찾기 위하여 시행되었다. 시판되고 있는 교정용 와이어와 브라켓에 sol-gel법, CVD (Chemical Vapor Deposition)법 및 PE-CVD (Plasma Enhanced-CVD)법으로 이산화티탄을 각각 코팅한 다음 각 방법으로 코팅된 이산화티탄 박막의 특성을 알아보고자 주사전자현미경을 이용하여 각 시편의 코팅박막 표면의 거칠기를 관찰하였고 adhesive tape pull test를 이용하여 코팅박막의 접착강도를 측정하였다. 메틸렌블루용액에 각 시편을 침지시킨 후 시간경과에 따른 메틸렌블루용액의 농도변화 측정을 통해 코팅박막의 분해능을 평가하였으며 불화나트륨 용액에 각 시편을 침지시킨 후 주사전자현미경을 이용하여 표면부식 정도를 관찰함으로써 불소화합물에 대한 내부식성을 평가하여 다음과 같은 결과를 얻었다. 코팅박막의 표면은 CVD법 및 PE-CVD법이 sol-gel법이나 코팅되지 않은 시편에 비해 더 매끄러웠다. 코팅박막의 접착강도는 PE-CVD법이 가장 높았고, CVD법, sol-gel법의 순으로 낮게 나타났다. 코팅박막의 메틸렌블루 분해능은 PE-CVD법이 가장 높았고, CVD법, sol-gel법의 순으로 낮게 나타났다. 코팅박막의 불소화합물에 대한 내부식성은 CVD법 및 PE-CVD법이 sol-gel법에 비해 높게 나타났다. 이상의 결과는 교정용 와이어 및 브라켓의 이산화티탄 광촉매 코팅 시 CVD법 및 PE-CVD법이 sol-gel법보다 적절한 방법임을 시사하였다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2002년도 추계학술대회 논문집 전기물성,응용부문
• /
• pp.91-93
• /
• 2002

Ti-Sn sol is fabricated using sol-gel method. In case the amount of water required hydrolysis smaller than that for stoichiometry, Ti sol forms clear sol which has normal chain structure. On the contrary, in case the amount of water required hydrolysis larger than that for stoichiometry, Ti sol forms suspended sol which has cluster structure. Viscosity of Ti-Sn sol decrease with increasing HCl additive. Gelation of Ti-Sn sol is delayed with increasing HCl and $Sn(OC_2H_5)_4$ additive.