• Geomechanics and Engineering
• /
• v.13 no.5
• /
• pp.775-791
• /
• 2017

Surface wave techniques are widely used as non-invasive method for geotechnical site characterization. Field surface wave data are collected and analyzed using different processing techniques to generate the dispersion curves, which are further used to extract the shear wave velocity profile by inverse problem solution. Characteristics of a dispersion curve depend on the subsurface layering information of a vertically heterogeneous medium. Sometimes soft layer can be found between two stiff layers in the vertically heterogeneous media, and it can affect the wave propagation dramatically. Now most of the surface wave techniques use the fundamental mode Rayleigh wave propagation during the inversion, but this may not be the actual scenario when a soft layer is present in a vertically layered medium. This paper presents a detailed and comprehensive study using finite element method to examine the effect of soft layers which sometimes get trapped between two high velocity layers. Determination of the presence of a soft layer is quite important for proper mechanical characterization of a soil deposit. Present analysis shows that the thickness and position of the trapped soft layer highly influence the dispersion of Rayleigh waves while the higher modes also contribute in the resulting wave propagation.

• Proceedings of the KSR Conference
• /
• 2000.05a
• /
• pp.392-398
• /
• 2000

When soft ground improvement is proceeded in costal area using compulsory replacement method, it is very important that the method of stability of embankment above replacement layer can be obtained if non-replaced soft layer is remained, and there are a lot of influence factors which affect the stability of embankment, such as replacement depth, the water content of dredged soil and the width of replacement layer, etc. If soft layer was replaced completely by good quality materials, there would be no problems about stability of embankment, but practically non-replaced layer would be remained as the strength of soft layer will be increased. So another consideration is required to get the stability of embankment. In this study, stability of embankment among these factors was compared, and from that results, the better way that could obtain the stability was presented.

• Journal of Pharmaceutical Investigation
• /
• v.24 no.1
• /
• pp.25-28
• /
• 1994

The previous vitamin assays in soft capsules have been performed only with capsule contents. Since some vitamins, however, could migrate into gelatin layer of the soft capsules, each vitamin of multivitamin soft capsules in the market was analyzed simultaneously in both capsule content and gelatin layer. The results showed that migrations of nicotinamide and pyridoxine hydrochloride into gelatin layer were pronounced, while those of other vitamins were negligible.

• Proceedings of the Korean Magnestics Society Conference
• /
• 2003.06a
• /
• pp.28-29
• /
• 2003

• The Journal of Korean Academy of Prosthodontics
• /
• v.49 no.4
• /
• pp.324-332
• /
• 2011

Purpose: The purpose of this study was to compare the stress distribution of teeth and jaw on load by differentiating property of materials according to each layer of widely used mouthguard. Materials and methods: A Korean adult having normal cranium and mandible was selected to examine. A customized mouthguard was constructed by use of DRUFOMAT plate and DRUFOMAT-TE/-SQ of Dreve Co. according to Signature Mouthguard system. The cranium was scanned by means of computed tomography with 1mm interval. It was modeled with CANTIBio BIONIX/Body Builder program and simulated and interpreted using Alter HyperMesh program. The mouthguard was classified as follows according to the layers. (1) soft guard (Bioplast)(SG) (2) hard guard (Duran)(HG) (3) medium guard (Drufomat)(MG) (4) soft layer + hard layer (SG + HG) (5) hard layer + soft layer (HG + SG) (6) soft layer + hard layer + soft layer (SG + HG + SG) (7) hard layer + soft layer + hard layer (HG + SG + HG) The impact locations on mandible were gnathion, the center of inferior border, and the anterior edge of gonial angle. And the impact directions were oblique ($45^{\circ}$). The impact load was 800 N for 0.1 sec. The stress distribution was measured at maxillary teeth, TMJ and maxilla. The statistics were conducted using Repeated ANOVA and in case of difference, Duncan test was used as post analysis. Results: In teeth and maxilla, the mouthguard contacting soft layer of mandibular teeth presented lowest stress measure and, in contrast, in condyle, the mouthguard contacting hard layer of mandibular teeth presented lowest stress measure. Conclusion: For all impact directions, soft layer + hard layer + soft layer, the mouthguard with three layers which the hard layer is sandwiched between two soft layers, showed relatively even distribution of stress in impact.

• Current Research on Agriculture and Life Sciences
• /
• v.2
• /
• pp.98-108
• /
• 1984

Generally, in case of constructing the embankments on the soft clay layers, one-dimensional consolidation settlement under the assumption of a middle position stress in a single layer makes a great difference with the integral value, ie. the final settlement. Consequently, to find how many equal segments of the soft clay layer are needed to converge into the integral value and which position should be taken as a position of mean stress, authors compared the theoretical value of the settlement due to one-dimensional consolidation with the practical value of the settlement due to two dimensional consolidation. The obtained results are as follows. 1) The practical value of the two-dimensional consolidation settlement can be estimated by the 74-83% theoretical value of the one-dimensional consolidation settlement. 2) When the soft clay layer was cut into 8-16 equal segments according to the depth, one-dimensional consolidation settlement converge into the integral value. 3) Assuming a total soft clay layer as a single one, the depth of a mean stress position is 0.29-0.37 of the thickness of the total soft clay layer. 4) The Hyperbola Method which presumes the long-term settlement from the short-term practical value of settlement is credible, because all practical value of the settlement are in safe side of the standard error of estimation and the correlation coefficient is up to 0.95.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.14 no.5
• /
• pp.430-437
• /
• 2021

In this paper, we propose a robust face recognition method against soft errors with a deep convolutional generative adversarial network(DCGAN) based compensation method by a cross-layer approach. When soft-errors occur in block data of JPEG files, these blocks can be decoded inappropriately. In previous results, these blocks have been replaced using a mean face, thereby improving recognition ratio to a certain degree. This paper uses a DCGAN-based compensation approach to extend the previous results. When soft errors are detected in an embedded system layer using parity bit checkers, they are compensated in the application layer using compensated block data by a DCGAN-based compensation method. Regarding soft errors and block data loss in facial images, a DCGAN architecture is redesigned to compensate for the block data loss. Simulation results show that the proposed method effectively compensates for performance degradation due to soft errors.

• Structural Engineering and Mechanics
• /
• v.59 no.2
• /
• pp.227-241
• /
• 2016

A circular plate with constant thickness, finite radius and stiff edge lying on an elastic halfspace is considered. The half-space consists of a soft functionally graded (FGM) layer with arbitrary varying elastic properties and a homogeneous elastic substrate. The plate bends under the action of arbitrary axisymmetric distributed load and response from the elastic half-space. A semi-analytical solution for the problem effective in whole range of geometric (relative layer thickness) and mechanical (elastic properties of coating and substrate, stiffness of the plate) properties is constructed using the bilateral asymptotic method (Aizikovich et al. 2009). Approximated analytical expressions for the contact stresses and deflections of the plate are provided. Numerical results showing the qualitative dependence of the solution from the initial parameters of the problem are obtained with high precision.

• Journal of the Korean Geosynthetics Society
• /
• v.17 no.2
• /
• pp.1-7
• /
• 2018

The number of construction of roads and railroads in soft ground such as coastal areas and wetlands is getting increased. For this reason cases that soft ground improvement is applied are increasing. In general, many ground improvement methods consider only the working conditions at the time or only economy. But if the working condition and economy are taken into consideration together, the number of applicable construction method gets limited. In such a case, a ground improvement method using both the surface layer portion and the deep layer portion is applied. But the basic research on this is still insufficient in practice. Therefore, in this study the reinforcement effect of geogrid was investigated by carrying out the model test realizing the case in which soft surface ground improvement and depth improvement are simultaneously applied. And it was intened to understand the effect of the thickness of surface layer, the diameter and length of the improvement body on the reinforcement effect of geogrid. The result showed that the effect of the surface layer thickness is greater than the effect of the deep layer diameter. Moreover, when the surface layer is reinforced with a geogrid, the strength of the surface layer part is enhanced and this effect of a geogrid reinforcement caused the reduction of surface settlement.

• The Journal of Engineering Geology
• /
• v.29 no.4
• /
• pp.427-437
• /
• 2019

The purpose of this study is to improve construction cost, time, and field management when constructing a road on soft soil foundation by eliminating extra-banking of subgrade layer after completion of the consolidation process. The subgrade layer was pre-constructed before the soft ground improvement. And then it was confirmed by the field test that the compaction effect was maintained or not after consolidation settlement. As a result of the experiment, all subgrade layers were kept constant except for the top subgrade layer. So it would be advantageous to secure economical and practical in road construction if subgrade layers were constructed exclusive of the top subgrade layer.