• Journal of the Korean Wood Science and Technology
• /
• v.31 no.6
• /
• pp.31-39
• /
• 2003

The enzymatic isolation of residual lignins obtained from spruce and beech pulps (obtained by sulfite, kraft, ASAM and soda/AQ/MeOH pulping processes) and their characterization was described in previous publications. Here, the residual lignins have been submitted to potassium permanganate oxidation (KMnO₄ degradation), and 9 aromatic carboxylic acids (3 of them are dimeric) were identified after methylation with diazomethane by GC/MS. The analytical challenge during qantification by the internal standard methods was the partly high protein content of the samples, which resulted in elevated anisic acid yields in the degradation mixture of sulfite residual lignins. The results are compared with the KMnO₄ degradation of the corresponding MWLs and discussed in terms of S/G ratios and degrees of condensation. The latter was calculated as a quotient between the aromatic carboxylic acids derived from condensed and non-condensed lignin structures. Typical degradation patterns for the various processes have been observed. Among other parameter, the relative compositions between iso-hemipinic acid (which is for condensation in pos. 5 of the aromatic ring) and meta-hemipinic acid and 3,4,5-trimethoxyphthalic acid (both are for condensation in pos. 6 of the aromatic ring) was found to be process specific. Kraft and soda/AQ/MeOH residual lignins yielded higher amounts of iso-hemipinic acid. In contrast, the relative yields of meta-hemipinic acid and 3,4,5-trimethoxyphthalic acid (the latter in beech lignins) are higher in sulfite and particularly in ASAM residual lignin. In case of beech residual lignins the amount of acids originated from non-condensed syringyl type lignin units was surprisingly high. The condensation degree of residual lignins was shown to be generally higher than that of MWLs. This was especially true for the G units. ASAM residual lignin exhibited very high S/G ratios and degrees of polymerization. Causality between condensation degree and total yield of degradation products was demonstrated.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.48 no.2
• /
• pp.91-98
• /
• 2016

Cellulose nanofibrils (CNF) was made from oil palm trunk (OPT) with soda-anthraquinone pulping, chlorine dioxide bleaching, carboxymethylation, followed by mechanical grinding. Size of this CNF was 16-40 nm of width confirmed by TEM. To evaluate CNF from OPT as cosmetics raw materials for moisturizing component, water holding properties was compared with hyaluronic acid and collagen. CNF from OPT had better water holding property than collagen or hyaluronic acid whether phenoxyethanol was added as antiseptic or without additive.

• Journal of the Korean Wood Science and Technology
• /
• v.9 no.3
• /
• pp.7-15
• /
• 1981

A Japanese larch has been reforested very much in Korea, but it is not used as a wood resources for paper pulp by now. So this study is carried out to utilize the larchwood for paper pulp manufacture through the Asplund pulping process. The experiment on increasing in the brightness of the pulp is made through the addition of $MgSO_4$, $ZnSO_4$, $Al_2(SO_4)_3$, and KI as a cellulose stabilizer in chip treatment with caustic soda which is followed by high-temperature defibration and conventional peroxide bleaching (5% NaOH plus 2% additive salt per wood in cold pretreatment), or in high-consistency (30%) pulp bleaching of hydrogen peroxide and peracetic acid (100% acitve oxygen per lignin) for conventional one. The results obtained are as follows: 1. The solution of 0.5% additive salts had different pH by the sort of bases that was pH 5.7 in $MgSO_4$, liquor, pH 4.9 for $ZnSO_4$, and pH 2.9 for $Al_2(SO_4)_3$, and in the precepitation of bases which ranged to pH 6-13 for $MgSO_4$, pH 5-12 for $ZnSO_4$, and pH 3-10 for $Al_2(SO_4)_3$. 2. The cellulose stabilizer affective in high-consistency peroxide bleaching was KI, $MgSO_4$, and $ZnSO_4$, but has made a little improvement in de lignification and brightness of pulp in comparison with no addition. 3. The higher alkalinity in the chip treatment has made the higher strength and brightness of larchwood Aspiund pulp instead of downing the pulp yield. And the effective compound for cellulose stabilizer in caustic soda pretreatment of chip was $ZnSO_4$, $Al_2(SO_4)_3$ and KI in order for the conventional peroxide bleaching after Asplund pulping. 4. Therefore, the more effective additives for cellulose stabilization in high-temperature defibration of larchwood suppose to be $ZnSO_4$, $Al_2(SO_4)_3$, and KI, while KI and $MgSO_4$ for peroxide bleaching.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.46 no.6
• /
• pp.71-77
• /
• 2014

Despite the ubiquity of electronic media, paper is still the most generally readable carrier of information. Because paper materials are deteriorated by chemical, biological and physical factors over time, there have been major concerns about the decay of large collections of books, publications, old maps, historical artifacts, and written records. Therefore, manufacture of permanent paper has been a highly debated issue in paper conservation research. Through the use of permanent paper, our new records, journals, library books, art works, and all culturally and historically important documents can be preserved. In this study, handsheets were made of mixture of hemp bast fiber produced by soda pulping and HwBKP varying the amount of hemp. Physical, mechanical and optical properties of each handsheet were examined. As the ratio of hemp bast fiber increased, mechanical properties were improved significantly, but opacity decreased. After aging, the optical properties of the handsheets mixed with the hemp bast fiber more decreased than those of the non-mixed handsheet. The more mixture ratio of hemp bast fiber increased, the more decreasing rate of optical properties increased. As a result, it was confirmed that hemp bast fiber is a very promising resource for the manufacturing of permanent paper.