• Journal of the Korean Solar Energy Society
• /
• v.26 no.1
• /
• pp.57-64
• /
• 2006

Cr-CrO cermet solar selective coatings with a double cermets layer film structure were prepared using a special direct current (dc) magnetron sputtering technology. The typical films structures from surface to bottom substrate were measured to be an $Al_2O_3$ anti-reflection layer on a double Cr-CrO cermet layer on an Al metal infrared reflection layer. Optical properties of optimized Cr-CrO cermet solar selective coating were absorptance (${\alpha}$) = 0.95 and emittance (${\varepsilon}$) = 0.10 ($100^{\circ}C$). Atomic force microscopy (AFM) image showed that Cr-CrO cermet film was very smooth and their grain size was also very small The results of thermal stability test showed that the Cr-CrO cermet solar selective coatings were stable for use at temperature of $400^{\circ}C$.

• Korean Journal of Plant Resources
• /
• v.15 no.2
• /
• pp.172-176
• /
• 2002

In order to investigate the possibility of utilizing cermet piece as a seed corm in taro, the cermet piece classified by the weight were planted on April 30, 2000. The effect of weight of cermets cutting by two pieces (5, 10, 15, and 20g) and four pieces (15g) on the growth, yield, and quality of taro was comparing with cormel follows as: The larger the size of cormel pieces was, the more number of leaves developed, and the higher the yield was. Also the growth of small cormel pieces was normal, so we forecast that it is possible to use small cermet pieces as seed cermet in mass production of taro.

• Korean Journal of Plant Resources
• /
• v.14 no.3
• /
• pp.229-234
• /
• 2001

In order to investigate the possibility of utilizing small cermet as a seed corm in taro, the small cermets classified by the weight were planted on April 30,2000. The effect of weight of small cermets(5,10, If,20,25, and 30g) and corms on the growth, yield, and quality of taro was compared to those raised from cermets. The larger the size of cormel was, the more number of leaves developed, and the higher the yield was. Also the growth of small cormel was normal, so we forecast that it is possible to use small cermet as seed corm in mass production of taro.

• Journal of the Korean Ceramic Society
• /
• v.35 no.12
• /
• pp.1316-1322
• /
• 1998

The amount of VC and C/N ratio in Ti(CN) was varied to investigate the effect of VC addition on the mi-crostructural change in Ti(CN)-Ni system. As the amount of VC addition increases in Ti(C0.7N0.3)-20Ni sys-tem a complete solid solution was observed in Ti(C0.7N0.3)-20Ni-25VC system. It implies that the ratio of the dissolution rates of Ti(C0.7N0.3)to that of VC is nearly 2:1 at the sintering conditions used in this study. It was found from the experiments that the system composed of the Ti(C0.7N0.3) phase exhibits a rimless structure and relatively small amount of solid solution. That is among Ti(C0.7N0.3) phase exhibits a rimless structure and relatively small amount of solid solution. This is among Ti(C1-xNx) phases the dissolution rate of Ti(C0.3N0.7) is the lowest. Also fracture toughness(KIC) of the cermet was measured by indentation method. Attentions were paid to crack propagation path to look for a dominant fracture mode and to cor-relate it with fracture toughness values. The fracture toughness was relatively high with the addition of VC content. But the addition of a large VC content reduced the overall toughness of the cermet. This result is explained with the difference in fracture mode.

• Nuclear Engineering and Technology
• /
• v.53 no.7
• /
• pp.2095-2103
• /
• 2021

A small power ADS design using thorium oxide and diluent matrix reprocessed fuel is proposed for a high transmutation rate, small reactivity swing, and strong safety features. Two fuel matrices (CERCER and CERMET) and different recycled fuel compositions recovered from UO₂ spent fuels with 45 GWd/tU and 60 GWd/tU burnup were investigated to determine the suitable fuel for the ADS. It was found that the transmutation of each isotope depends on TRU initial loading amount. After examining the cores, the results show that CERCER fueled ADS has a negative coolant void reactivity (CVR) and a smaller radiotoxicity at discharge compared to that of CERMET core. It implies that CERCER fuel has enhanced safety features and more flavor in terms of radiotoxicity management. To increase fuel utilization and core operation efficiency, a simple assembly shuffling pattern for the CERCER fueled ADS is also proposed. Eigenvalue and burnup calculations were conducted using Serpent 2 with ENDF/B-VII.0 library in both kcode and external source modes, and it indicates that the results of transmutation analyses obtained by kcode only is reliable to discuss the transmutation potential of ADS. Burnup calculation with the fixed-source mode is essential to be used for more practical results of the transmutation by ADS.

• Journal of Powder Materials
• /
• v.14 no.2 s.61
• /
• pp.132-139
• /
• 2007

In the Ti(CN)-Co/Ni cermet, WC is an effective additive for increasing sinterability and mechanical properties such as toughness and hardness. In this work, WC, (WTi)C and (WTi)(CN) were used as the source of WC and their effects were investigated in the respect of microstructural evolution and mechanical properties. Regardless of the kinds of WC sources, the hard phase with dark core and bright rim structure was observed in the Ti(CN)-Co/Ni cermet under the incorporation of relatively small amount of WC. However, hard phases with bright core began to appear and their frequency increased with the increase of all kinds of WC source addition. The ratio of bright core to dark one in the (TiW)(CN)-Co/Ni cermet was greatest under the incorporation of (WTi)C compared at the same equivalent amount of WC. The mechanical properties were improved with the addition of WC irrespective of the kinds of sources, but the addition of (WTi)(CN) was less effective for the increase of fracture toughness.

• Journal of the Korean Ceramic Society
• /
• v.36 no.4
• /
• pp.366-371
• /
• 1999

The effect of VC addition on the microstructural evolution of Fe-TiC cermet has been investigated. The microstructures of the Fe-TiC varied with the amount of VC addition. The addition of 1wt% VC enhanced the instability of liquid-solid interface ; the dissolving interface showed round shape instead of facetted one which was ascribed to the increase of lattice mismatch between TiC and solid-solution carbide. in the speci-men with 10wt% VC the new set of solid-solution carbide grains of uniform and small size was formed in-side coarse TiC particles by diffusion induced recrystallizatin (DIR). With increasing the heat-treatment time fine recrystallized grains were dispersed homogeneously in the matrix and resulted in the increase in fracture strength.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.21 no.4
• /
• pp.23-30
• /
• 2022

Small-scale production is increasing, and the manufacturing industry is gradually changing into a smart manufacturing industry. Therefore, research on securing optimal cutting conditions for factors affecting machining precision during cutting is very important. Therefore, the purpose of this study is to After machining the inner diameter hole of SCM415 steel with a cermet tool on a CNC automatic lathe, the surface roughness, dimensional accuracy, and dimensional straightness are measured according to the feed rate to analyze the machining characteristics and suggest optimal cutting conditions. The test material was cut using a cermet tool for secondary cutting after a round bar with a diameter of 20 mm was mounted on a CNC automatic lathe. The cutting length was fixed at 0.5 mm, and the cutting speed was fixed at 3200 rpm. When the feed rate was changed to 0.05, 0.1, and 0.15 mm/rev, the respective surface roughness during the 15th test was measured. Consequently, The lower the feed rate, the better is the surface roughness. In addition, the optimum cutting conditions for SCM415 steel were observed to be the most ideal cutting conditions than the condition of 0.05 mm/rev at a cutting speed of 3,200 rpm and a feed rate of 0.1 mm/rev.

• Journal of Korea Foundry Society
• /
• v.42 no.3
• /
• pp.191-197
• /
• 2022

This study aims to improve the machinability of gray cast irons in high speed cutting by using nonmetallic inclusions. In this research, small quantities of AL and Mg were added to conventional gray cast irons without influencing their mechanical characteristics and castability to investigate the effects of these nonmetallic inclusions in the gray cast irons on tool wear in high speed cutting. During the high speed turning of gray cast iron containing Al and Mg using a cermet tool, protective layers consisting of Al, Mg, Si, Mn, S and O were detected on the flank face and rake face of the tool, and flank and crater wear were significantly reduced compared to the turning of conventional gray cast iron and gray cast iron added with Al. The effect of inclusions on tool wear increased with increasing cutting speed, and flank and crater wear was the smallest at the cutting speed of 700m/min. Moreover, in face milling, the addition of Al and Mg drastically decreased the wear rate, and wear hardly progressed even in prolonged cutting length after initial wear. The amount of adhesion on tool faces increased as the cutting speed increased. This increase in cutting speed resulted in the formation of a thick protective layer and the reduction of tool wear. Furthermore, the addition of small amounts of Al and Mg prevented thermal cracks in the face milling of gray cast irons.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2002.11a
• /
• pp.8-8
• /
• 2002

TiC core/(Ti,Mo)C rim structure in TiC-$Mo_2C$-Ni base cermet which is generally prepared by sintering below 145$0^{\circ}C$ had been believed to be generated by the solid diffusion of Mo atoms 1 into TiC grains (D. Moskowitz and M.Humenik, 1r.:1966). Afterward, it was clarified that the c core/rim structure is generated by solution/re-precipitation mechanism : (1) $Mo_2C$ grains and s small TiC grains dissolve into the Ni liquid, (2) the dissolved Mo, Ti and C atoms migrate to the s surface of TiC coarse grains, (3) the Mo, Ti and C precipitate on the surface of TiC coarse g grains and form (Ti,Mo)C solid solution rim, and (4) the Ostwald ripening (grain growth by s solution/re-precipitation mechanism) of TiC-core/(Ti,Mo)-rim grains continues, and thus the w width of (Ti,Mo)C rim (at the same time, the grain size) increases with sintering time, etc. ( (H.Suzuki, K.Hayashi and O.Terada: 1973). The TiC-core was found not to disappear even by s sintering at 190$0^{\circ}C$ (ibid.: 1974) Recently, FeSi core/$Fe_2Si_5$-rim structure in Fe-66.7at%Si thermoelectric aIloy was found to also h hardly shrink and disappear by long heating at an appropriate temperature (1999: M.Tajima and K K.hayashD. Then, the authors considered its cause, and clarified experimentaIly that the disappearance of FeSi-core/$Fe_2Ski_5$-rim structure could be attributed to the exhaustion of diffusion-contributable vacancies in core/rim structure (N.Taniguchi and K.Hayashi:2001). At p present, the authors and my coworker are investigating whether the non-disappearance of TiC c core can be explained also from the new hypothesis "Exhaustion of diffusion-contributable v vacancies in corelrim structure".ure".uot;.