• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.17 no.3
• /
• pp.20-26
• /
• 2008

Nanoimprint lithography(NIL) is becoming next generation lithography of significant interest due to its low cost and a potential patterning resolution of 10nm or less. Success of the NIL relies on the adequate conditions of pressure, temperature and time. To have the adequate conditions for NIL, one has to understand the polymer flowing behavior during the imprinting process. In this paper, an analytical approach of polymer flow in thermal NIL was performed based on the squeeze flow with partial slip boundary conditions. Velocity profiles and pressure distributions of the polymer flow were obtained and imprinting forces and residual thickness were predicted with the consideration of the slip velocity between the polymer and the mold/substrate. The results show that the consideration of the slip is very important for investigating the polymer flow in Thermal NIL.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2014.10a
• /
• pp.830-832
• /
• 2014

In this study, friction stick-slip vibration're interpretation of the phenomenon, we used a statistical model of friction. In a previous study using a definite friction factor, but to a dynamic simulation using a constantly changing during the integration time by a Monte Carlo simulation method, not the average coefficient of friction and the dynamic friction coefficient and a constant value in this study.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09b
• /
• pp.866-867
• /
• 2006

This work will report a highly textured ${\beta}-Si_3N_4$ ceramic by aqueous slip casting in a magnetic field and subsequent pressureless sintering, Effects of the sintering aids, polymer dispersant, pH and stirring time on the stability of the $Si_3N_4$ slurries were studied. The textured ${\beta}-Si_3N_4$ with 97 % relative density could be obtained by slip casting in a magnetic field of 12 T and subsequent sintering at $1800^{\circ}C$ for 1 h. The textured microstructure is featured by the alignment of c-axis of ${\beta}-Si_3N_4$ crystals perpendicular to the magnetic field, and the Lotgering orientation factor, f, is determined to be 0.8.

• Proceedings of the KIEE Conference
• /
• 2000.11b
• /
• pp.405-407
• /
• 2000

The most generally implemented method to detect the ground speed of the railway vehicles is to use the rotary type speed sensor attached to wheel axle. The Slip or sliding phenomenon on the railway vehicles occurs frequently caused by the weak viscosity of the wheel. Thus, precisely to control the car, the slip/sliding detection system is required. In this paper we proposed for the speed data management system, which uses rotary type speed sensor. Proposed speed management system can detect the slip/sliding with wheel axle as well as correct the generated speed error during in error time, to provide accurate speed and precise location data. The effectiveness for adapting to the railway system is clarified by the computer simulation.

• Earthquakes and Structures
• /
• v.24 no.5
• /
• pp.365-375
• /
• 2023

Energy dissipation systems increase the energy dissipation capacity of buildings considerably. In this study, the effect of dampers on a typical 10-storey reinforced concrete structure with a ductile moment-resisting frame was investigated. In this context, 5 different models were created according to the calculation of the slip load and the positions of the dampers in the structure. Nonlinear time-history analyzes using 11 different earthquake acceleration records were performed on the models using the ETABS program. As a result of the analyses, storey displacements, energy dissipation ratios, drift ratios, storey accelerations, storey shears, and hysteretic curves of the dampers on the first and last storey and overturning moments are presented. In the study, it was determined that friction dampers increased the energy dissipation capacities of all models. In addition, it has been determined that positioning the dampers in the outer region of the structures and taking the base shear as a basis in the slip load calculation will be more effective.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.21 no.6
• /
• pp.811-823
• /
• 2019

Slip form method is applied to many cases of a shaft these days because it is safer, more economical and faster than cast-in-place method. Slip-up height of the method is approximately 2.5 to 4.0 m/day. If the temperature of concrete is outside the range of 10 to 30℃, the effects of changes in strength or elastic characteristics are significant. Therefore, it is difficult for slip-up speed to be higher than 3 m/day during winter construction. In addition, concrete has heat caused by hydration, which causes temperature cracking of hardened concrete. Therefore, temperature control of concrete curing is necessary for the continuous slip-up of slip form. In this study, the rebound hardness, time of ultrasonic waves propagation, heat of hydration, and external temperature are measured by developing heating panels and test devices for the continuous slip-up. Based on this, heating slip form is manufactured; this was applied to "Kimpo sites" and "Sinwol sites". The compared slip-up speed samples were 1.9 m/day or 0.200 m/hr on average at Gimpo sites (08:00~17:30) and 2.0 m/day or 0.210 m/hr at Sinwol sites.

• International Journal of Automotive Technology
• /
• v.3 no.4
• /
• pp.165-170
• /
• 2002

For a vehicle Anti-lock Braking System (ABS), the control target is to maintain friction coefficients within maximum range to ensure minimum stopping distance and vehicle stability. But in order to achieve a directionally stable maneuver, tire side forces must be considered along with the braking friction. Focusing on combined braking and turning operation conditions, this paper presents a new control scheme for an ABS controller design, which calculates optimal target wheel slip ratio on-line based on vehicle dynamic states and prevailing road condition. A fuzzy logic approach is applied to maintain the optimal target slip ratio so that the best compromise between braking deceleration, stopping distance and direction stability performances can be obtained for the vehicle. The scheme is implemented using an 8-DOF nonlinear vehicle model and simulation tests were carried out in different conditions. The simulation results show that the proposed scheme is robust and effective. Compared with a fixed-slip ratio scheme, the stopping distance can be decreased with satisfactory directional control performance meanwhile.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.41 no.1
• /
• pp.63-68
• /
• 2017

This paper reviews the learning model of a forward slip ratio in order to improve the mass-flow stability and strip qualities in the hot strip finishing mill process. Firstly, it is shown, from mathematical analysis, that the significant parameters of the forward slip ratio are the tension, looper angle, and roll velocity. Secondly, a discrete-time learning model of the forward slip ratio is proposed from these parameters, which is identified by an instrumental variable (IV) identification algorithm. Finally, it is shown from computer simulation that the proposed learning model is more effective than the existing learning model.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.3 no.4
• /
• pp.19-29
• /
• 1995

This paper discusses the stick-slip phenomenon of the driveline system of a vehicle in consideration of friction. Friction is operated on the between of flywheel and clutch disk. The expressions for obtaining the results have been derived from the equation of motion of a three degree of freedom frictional torsion vibration system which is made up driving part(engine, flywheel), driven part(clutch, transmission) and dynamic load part(vehicle body) by applying forth-order Rungekutta method. It was found that the great affect parameters of the stick-slip or stick motion were surface pressure force between flywheel and clutch disk, time decay parameter of surface pressure force and 1st torsional spring constant of clutch disk when driveline system had been affected by friction force. The results of this study can be used as basic design data of the clutch system for the ride quality improvement of a car.

• Journal of KSNVE
• /
• v.11 no.3
• /
• pp.461-470
• /
• 2001

A friction-type clutch system sometimes generates spick-slip vibration during engagement, which disturbs smooth start of a car and makes a passenger uncomfortable. In this study, the spick-slip vibration in four types of friction couples was investigated at two different engagement conditions respectively of which the amount of slip time and clutch travel was varied. Results are found as follows. First, the vibration increased at the condition of small engine torque and large torque fluctuations due to higher harmonics of engine speed. Second, the friction couple without a pre-damper has advantages of reducing the vibration. This study also suggested an evaluation method of vehicle vibration in the view point of human perception by using the frequency weighting of ISO2631-1.