• 한국인터넷방송통신학회논문지
• /
• 제21권5호
• /
• pp.27-32
• /
• 2021

본 논문은 16-QAM 신호 전송시 시분산 채널에서 발생되는 부호간 간섭을 경감시키기 위하여 사용되는 FC-MMA 적응 등화 알고리즘에서 고정 스텝 크기에 따른 등화 성능을 평가하였다. FC-MMA는 기존 MMA의 통신 채널의 시변 특성 및 순단과 같은 비정상적인 상황에서 신속하게 새로운 환경에 적응토록 빠른 수렴 속도를 갖는 것이 특성이지만, 수렴 속도는 고정 스텝 크기에 의하여 결정된다. 논문에서는 고정 스텝 크기값에 따른 등화 성능을 평가하였으며, 관련된 성능 지수로는 수렴 특성을 나타내는 잔류 isi와 최대 찌그러짐, MSE 및 잡음 강인성을 나타내는 SER과 군지연 보상 능력등이 사용되었다. 컴퓨터 시뮬레이션 결과 적응 스텝 크기가 클수록 정상 상태에 도달하는 수렴 속도는 개선되지만, 정상 상태 이후의 잔여량에서는 스텝 크기가 적을수록 우월해짐을 알 수 있었다. 본 연구 결과 FC-MMA 알고리즘은 초기에는 스텝 크기를 크게 설정하고, 정상 상태에 도달하면 이를 적게 조정하여 등화 잔여량을 최소화시킬 수 있을 것으로 기대된다.

• Food Science and Biotechnology
• /
• 제17권2호
• /
• pp.324-329
• /
• 2008

The effect of ultra-high pressure homogenization on the emulsifying properties of whey protein was investigated in a model emulsion made with whey protein isolate and soya oil under various pH. The emulsifying properties, the average diameter of the oil droplets ($d_{vs}$), and the protein load, were measured for each emulsion produced at different homogenization pressures (50 to 200 MPa) and pH values (4.6 to 8.0). According to the results of variance analysis and response surface, the pH had more influence on oil droplet size and protein load than homogenization pressure. The model equations, which were obtained by response surface analysis, show that pH and homogenization pressure had the major effect on oil droplet size and protein load. Higher homogenization pressure decreased the average droplet size and the protein load. Homogenization at high pressure, as opposed to low pressure, causes no overprocessing, but the effect was pH-dependent. The average diameter of the oil droplets increased slightly by decreasing the pH from 8.0 to 6.5 and then increased dramatically toward the isoelectric point of whey protein (i.e., at pH 4.6). Moreover associated droplets were found at acidic pH and their size was increased at high temperature.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2004년도 추계학술대회
• /
• pp.1152-1157
• /
• 2004

Temporal behavior of the laser induced incandescence (LII) signal is often used for soot particle sizing, which is possible because the cooling behavior of a laser heated particle is dependent on the particle size. In present study, LII signals of soot particles are modeled using two non-linear coupled differential equations deduced from the energy- and mass-balance of the process. The objective of this study is to see the effects of particle size, laser fluence on soot temperature characteristics and cooling behavior. Together with this, we focus on validating our simulation code by comparing with other previous results. Results of normalized LII signals obtained from various laser fluence conditions showed a good agreement with that of Dalzell and Sarofim's. It could be found that small particles cool faster at a constant laser fluence. And it also could be observed that vaporization is dominant process of heat loss during first 100ns after laser pulse, then heat conduction played most important role while thermal radiation had little influence all the time.

• 한국근적외분광분석학회:학술대회논문집
• /
• 한국근적외분광분석학회 2001년도 NIR-2001
• /
• pp.1129-1129
• /
• 2001

Maize, in Hungary, is the fodder-plant grown in the biggest quantity. It is not only used as a fodder but other products such as iso-sugar are made from it, too. The quality of the fodder and the produce is largely dependent on the composition of the supplied maize to the processing site. The examination of quality parameters besides conventional methods are investigated and measured by NIR spectroscopy on a routine basis. The investigated parameters are the following: water, total protein, starch and oil content. The accuracy and precision of determining these parameters we, apart from the wet chemical methods, influenced by sample preparation to a great extent. One of the main features of this is the sample particle size and its distribution across the sample. The uneven distribution of particle size negatively influences the measurement accuracy, decreases model robustness and prediction ability. With these in mind the aim of our experiment was to investigate the effect of particle size on the accuracy of maize composition determination using reflection measurement setup. In addition, we tested different spectrum transformations, which are suitable for canceling this effect. In our experiment 47 samples were analyzed with three different mesh sizes (1.5mm, 1.8mm and 2mm). The results of our findings are presented here.

• 한국재료학회:학술대회논문집
• /
• 한국재료학회 2003년도 추계학술발표강연 및 논문개요집
• /
• pp.71-71
• /
• 2003

Hot embossing has been widely accepted as an alternative to photolithography in generating patterns on polymeric substrates. The optimization of embossing process should be accomplished based on polymer substrate materials. In this paper, the effect of polymer substrates on nano scale hot embossing process was studied. Silicon molds with nano size patterns were fabricated by e-beam direct writing. Molds were coated with self-assembled monolayer (SAM) of (1, 1, 2.2H -perfluorooctyl)-trichlorosilane to reduce the stiction between mold and substrates. For an embossing, pressure of 55, 75 bur, embossing time of 5 min and temperature of above transition temperature were peformed. Polymethylmethacrylates (PMMA) with different molecular weights of 450,000 and 950,000, MR-I 8010 polymer (Micro Resist Technology) and polyaliphatic imide copolymer were applied for hot embossing process development in nano size. These polymers were spun coated on the Si wafer with the thickness between 150 and 200 nm. The nano size patterns obtained after hot embossing were observed and compared based on the polymer properties by scanning electron microscopy (SEM). The imprinting uniformity dependent on the Pattern density and size was investigated. Four polymers have been evaluated for the nanoimprint By optimizing the process parameters, the four polymers lead to uniform imprint and good pattern profiles. A reduction in the friction for smooth surfaces during demoulding is possible by polymer selection.

• Asian Journal of Atmospheric Environment
• /
• 제4권2호
• /
• pp.72-79
• /
• 2010

In this study, the ionic composition of volcanogenically derived particles and their temporal and spatial distributions have been investigated to evaluate the impact of the volcanic eruption on the local ecosystem and residents. To this end, an intensive field study was conducted to measure the size-segregated particulate matters at the east part of Sakurajima in Japan. Fractionated sampling of particles into > $PM_{10}$, $PM_{10-2.5}$, and $PM_{2.5}$ was made by a multi nozzle cascade impactor (MCI). The concentration of various ions present in the size-resolved particles was determined by Ion chromatography. The time dependent 3-dimensional Volcanic Ash Forecast Transport And Dispersion (VAFTAD) model developed by the NOAA Air Resources Laboratory (ARL) indicated that the sampling site of this work was affected by the volcanic aerosol particles plume. The temporal distributions of sulfate and $PM_{2.5}$ during the field campaign were significantly variable with important contributions to particle mass concentration. The chlorine loss, suspected to be caused by acidic components of volcanic gases, occurred predominantly in fine particles smaller than $10\;{\mu}m$.

• Journal of Welding and Joining
• /
• 제22권6호
• /
• pp.19-24
• /
• 2004

The laser welding and its analysis of thin-sheet carbon steels were carried out with high power $CO_{2}$ laser. The main factor of weld quality of laser welding is gap and edge quality. This work was preformed to focus on the gap tolerance problem during laser welding. First, bead on plate welding of thin sheet was examined to investigate the effect of laser welding variables, and to obtain optimum welding condition. Butt welding was also carried out to show the effect of gap on the laser weldability of thin sheet. In order to investigate the effect of gap on formability of welded thin sheet, LDH test was caried out. At high welding speed, the partial penetration was obtained by low heat input. Otherwise, porosity was formed in the bead at low weld speed because of too much heat input. The optimum welding condition of welding was derived from bead width, penetration and hardness property. The maximum gap tolerance on laser welding was observed to be about 0.2mm. This gap size has good relationship with beam size of laser spot(about 0.3mm). The formability of welded sheet was about $80{\%}$ value of base metal and the gap size has not affected on the formability, although weld quality is dependent on the gap size.

• Advanced Composite Materials
• /
• 제16권3호
• /
• pp.245-258
• /
• 2007

The single-modal Weibull model has been assessed on Tyranno ZMI Si-Zr-C-O fiber if a set of shape and scale parameters accurately reproduced the effect of the size of the diameter on strength. The tensile data of a single fiber have been divided into two expedient groups as 'small diameter' group and 'large diameter' group in deriving the parameters, which should be consistent if the Weibull model accurately reproduced the size effect. However, the derived Weibull parameters were inconsistent between the two groups. Thereby the authors have concluded that the parameters of the single-modal Weibull model are dependent on the fiber diameter, so that the model is inadequate to reproduce the strength size effect. On the other hand, Weibull parameters were found consistent between the two groups by excluding the data of 'large mirror zone' sample, which was defined as the sample around 10% mirror zone area of the fracture surface. What is more, the exclusion reduced the strength variance more drastically in the 'large diameter' group than in the 'small diameter' group, even though the 'large mirror zone' samples were found identical in the percentage between the two groups. The authors therefore conclude that diameter limitation to the 'small diameter' group level can lead to drastically less distributed strength values than the estimated strength through the Weibull scaling on the present Tyranno ZMI Si-Zr-C-O fiber.

• Bulletin of the Korean Chemical Society
• /
• 제31권8호
• /
• pp.2215-2218
• /
• 2010

The series of alkali metal perhalogenates, $MXO_4$ (M=Li, Na, K and X=F, Cl, Br, I) were theoretically studied with the help of MP2 methods. Bidentate as well as tridentate structures were found to be stable minima. The bidentate structures are becoming preferred as the size of halogen increases and as the size of metal decreases. Geometrically, the M-O and M-X distances of both bidentate and tridentate structures, increase with the size of metal. Generally, the M-$O_1$ distances of tridentate forms are longer than the corresponding distances of bidentate forms, while the M-X distances of tridentate forms show the opposite trend. Similarly, the X-O bonds increase with the size of halogens except $MXO_4$ pairs, where the X-O bonds are unusually long due to the enhanced oxygen-oxygen repulsions. In short, the relative energetics as well as the geometrical parameters are found to be strongly dependent on halogen and metal elements.

• 대한토목학회논문집
• /
• 제10권1호
• /
• pp.71-80
• /
• 1990

본(本) 논문(論文)에서는 동적하중(動的荷重)을 받는 콘크리트의 파괴특성을 규명하고, 동적하중하(動的荷重下)에서의 변화특성을 연구하였다. 이를 위하여 포괄적인 실험연구가 수행되었으며 부재크기의 영향을 분석하기 위하여 몇가지 시리즈로 분류하여 실험하였다. 본 실험으로부터 최대파괴하중(最大破壞荷重), 정적(靜的) 및 동적(動的) 파괴(破壞)에너지 그리고 공칭파괴응력이 계산되었다. 본(本) 연구결과(硏究結果) 변형속도(變形速度)가 증가함에 따라 콘크리트의 파괴에너지가 증가하는 것으로 나타났다. 또한, 부재의 크기가 커짐에 따라 파괴에너지 값이 상당히 변화되는 것으로 타나났다. 본(本) 연구(硏究)에서는 부재 크기에 따른 콘크리트의 정적(靜的) 및 동적(動的) 파괴에너지를 예측할 수 있는 예측공식을 도출하여 제시하였다. 본(本) 연구(硏究)는 콘크리트의 동적파괴거동해석에 유용한 기초자료가 될 것으로 사료된다.