• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.7
• /
• pp.353-362
• /
• 2019

Thermodynamic analysis of cascade refrigeration systems has attracted considerable research attention. On the other hand, a system evaluation based on thermodynamic analyses of the individual parts, including the evaporator, condenser, intercooler, expansion valve, etc., has received less attention. In this study, performance analysis was conducted on a cascade refrigeration system, which has an individual cooling and refrigeration evaporator, and equips the intercooler and air-cooled condenser in a series in a lower cycle. The thermo-fluid design was then performed on the major components of the system - upper condenser, lower condenser, cooling evaporator, refrigeration evaporator, intercooler, compressor, electronic expansion valve - of 15 kW refrigeration, and 8 kW cooling capacity using R-410A. A series of simulations were conducted on the designed system. The change in outdoor temperature from 26 C to 38 C resulted in the cooling capacity of the lower evaporator remaining approximately the same, whereas it decreased by 9% at the upper evaporator and by 63% at the intercooler. The COP decreased with increasing outdoor temperature. In addition, the COP of the cycle with the intercooler operation was higher that of the cycle without the intercooler operation. Furthermore, the increase in the upper condenser size by two fold increased the upper evaporator by 4%. On the other hand, the lower evaporator capacity remained the same. The COP of the upper cycle increased with increasing upper condenser size, whereas that of the lower cycle remained almost the same. When the size of the lower condenser was increased 2.8 fold, the intercooler capacity increased by 8%, whereas those of upper and the lower evaporator remained approximately the same. Furthermore, the COP of the lower cycle increased with an increase in the lower condenser. On the other hand, the change of the upper condenser was minimal.

• Economic and Environmental Geology
• /
• v.34 no.6
• /
• pp.627-648
• /
• 2001

At least two distinct types of layering are present in the middle zone of the Skaergaard intrusion; alternating plagioclase-rich and pyroxene-rich, macro-rhythmic layers, and smaller scale, modally-graded, rhythmic layers. The macro-rhythmic layers are ubiquitous in the middle zone of the Layered Series, but are not observed in the lower and upper zone of the Layered Series or in the wall or roof tories of the intrusion. They range from 0.3 to 17.3 m in thickness, have sharp upper and lower boundaries, and can be traced laterally for over 2 ]fm in outcrop. Although individual macrorhythmic layers are not internally graded, many contain smaller-scale, modally-graded layers. Modally-graded. rhythmic layers are a common feature of the Layered Series but are not abundant in either the Upper Border Series or the Marginal Border Series. They range in thickness from 1 to 50 cm and can be traced laterally in outcrop for up to 100 m. Their lateral termination ranges from abrupt to gradational, and they are often associated with cut and fill structures and crossbedding suggestive of current activity. They are characterized by sharp lower and gradational upper contacts, and by strong intra-layer modal grading with olivine, ilmenite, and magnetite concentrated at the base, pyroxene concentrated above the base, and plagioclase concentrated at the top. The layers are also grain-size graded with the maximum size for each phase occurring at the horizon in the layer where the phase is most abundant. Modally-graded, rhythmic layers in the middle zone of the Layered Series occur within both plagioclase-rich and pyroxene-rich macro-rhythmic layers.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.17 no.10
• /
• pp.2245-2251
• /
• 2013

In this paper, a design of a compact series-fed dipole pair(SDP) antenna with end-loaded rectangular patches is presented. In order to reduce the lateral size of a conventional SDP antenna, rectangular patches are end-loaded to the two dipole elements of the SDP antenna and a grooved ground plane is used by adding a patch at both ends of the ground plane. The effects of varying the length and width of the rectangular patches on the antenna performance such as input reflection coefficient are investigated. An optimized compact SDP antenna covering a frequency band ranging from 1.7 GHz to 2.7 GHz is designed and fabricated on an FR4 substrate. The total width of the fabricated prototype of the proposed antenna is reduced by approximately 14.3% compared to the conventional SDP antenna. Experimental results show that the antenna presents a 48.7% bandwidth in the range of 1.68-2.76 GHz and a stable gain of 5.6-6.0 dBi with minimal degradation. Moreover, a front-to-back ratio is improved by about 0.7 to 7.4 dB.

• The korean journal of orthodontics
• /
• v.50 no.6
• /
• pp.401-406
• /
• 2020

Objective: To investigate and compare the slot sizes and parallelism of metal injection molding (MIM) and computerized numerical control (CNC) brackets. Methods: The following four MIM bracket series with 0.022-inch (in) slots were selected for investigation: Di MIM mini Twin (Ortho Organizers), Mini Diamond Roth (Ormco), Gemini MBT (3M Unitek), and Formula R Roth (Tomy). The following four CNC bracket series with 0.022-in slots were selected for investigation: Econoline MBT (Adenta), Legend mini MBT (GC Orthodontics), Crown mini MBT (Adenta), and Evolve MBT (DB Orthodontics). The slot dimensions were measured using an optical microscope (XTCam-D310M; Mitutoyo) with a resolution of 1 ㎛. The results were statistically analyzed using one-way analysis of variance and the Tukey post-hoc test with a significance level of 0.05. Results: The results indicated that all the investigated slot sizes were oversized with respect to the manufacturers' specifications (0.022 in). Among the eight bracket series, the Di MIM bracket (MIM) was the most oversized by 10.4%, whereas the Evolve bracket (CNC) was the least oversized by 2.6%. The slots in seven of the bracket series had divergent walls instead of parallel ones. The Evolve bracket alone had parallel slot walls. Conclusions: Regardless of the manufacturing method, all the slot sizes of the brackets investigated in this study were significantly oversized; most of the slot walls were nonparallel, except for those of the Evolve bracket. This study could not establish that the CNC method was more accurate than the MIM method in manufacturing bracket slots.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.19 no.5
• /
• pp.399-406
• /
• 2014

This study investigates the structure and operation of the ITER VS converter and proposes a sequence control method for six series-connected VS converters to reduce reactive power. The operation and the proposed sequence control method are verified through RTDS simulation. The ITER VS converter must supply voltage/current to the superconducting magnets for plasma current vertical stabilization, and the four-quadrant operation must proceed without a zero-current discontinuous section. The operation mode of the VS converter is separated into a 12- and 6-pulse circulating current and transition modes according to the size of the load current. The output voltage of the unit VS converter is limited because of the rated voltage; however, the superconducting coil must increase the operating output voltage. Thus, the VS converter must be connected in a 6-series to provide the required operating output voltage. The output voltage of the VS converters is controlled continuously; however, reactive power is limited within a minimized value of the grid. In this study, the unit converter is compared with converters connected in a 6-series to determine a suitable sequence control method. The output voltage is the same in all cases, but the maximum reactive power is reduced from 100% to 73%. This sequence control method is verified through RTDS simulation.

• Journal of the Korea Concrete Institute
• /
• v.27 no.3
• /
• pp.273-281
• /
• 2015

In this paper, the performance of alkali-activated slag cement (AASC) is assessed in terms of compressive strength and drying shrinkage, using three different types of silica sand and river sand. The sand type has an important influence on the properties of AASC mortar. Three silica sands (SS1, SS2 and SS3) and river sand (RS) were considered. Three series of blended sands have been tested. A first series (S1) with RS and SS1, a second series (S2) with RS and SS2 and third series (S3) with RS and SS3 with a different blended ratios. The result shows a very significant influence of the blended sand on the AASC mortar properties. The compressive strength and drying shrinkage related with the particle sizes and blended ratios of sands are investigated considering blended sand properties like fineness modulus (FM) and relative specific surface. The type and blended ratio of sand seems to have very significant and important consequences for the mix design of the AASC mortar.

• Journal of the Korea Concrete Institute
• /
• v.25 no.5
• /
• pp.477-484
• /
• 2013

In this study, eleven reinforced concrete beams, ground granulated blast furnace slag, replacing recycled coarse aggregate (BRS series) and recycled coarse aggregate with steel fiber (BSRS series), and standard specimen (BSS) were constructed and tested under monotonic loading. Experimental programs were carried out to improve and evaluate the shear performance of such test specimens, such as the load-displacement, the failure mode and the maximum load carrying capacity. All the specimens were modeled in 1/2 scale-down size. Test results showed that test specimens (BSRS Series) was increased the compressive strength by 9%, the maximum load carrying capacity by 1~6% and the ductility capacity by 1.02~1.13 times in comparison with the standard specimen (BSS). And the specimens (BSRS Series) showed enough ductile behavior and stable flexural failure.

• Asian Pacific Journal of Cancer Prevention
• /
• v.16 no.3
• /
• pp.1277-1280
• /
• 2015

Aim: To report epidemiologic and anatomoclinical transitions of inflammatory breast cancer (IBC) in Tunisia. Materials and Methods: Data including clinico-pathological data for 208 cases of T4d or PEV 3 non-metastatic breast cancer diagnosed between 2005 and 2010 were collected from patient records. Chi2 and Z tests were used to compare variables with two Tunisian historical series and a series about Arab-American patients. Results: Thirty three percent of our patients had their first child before 23 years of age and 56% had their menarche before 12 years, 75% never receiving oral contraception. Obesity was observed in 42% of women and IBC occurred during pregnancy in 13% of cases. Tumor grade was II-III in 90% of cases, HR was negative in 52%, HER2 was over expressed in 31% and invasion of more than 3 axillary nodes occurred in 18% of patients. We observed a pCR rate of 19% after neoadjuvant treatment (anthracyline-taxane used in 79%, trastuzumab in 27% ). Compared to historical Tunisian series (since 1996), IBC epidemiology remained stable in terms of median age, menopausal status and obesity. However we observed a significant decrease in median clinical tumor size and number of positive axillary lymph nodes. Comparison to IBC in Arab-Americans showed a significant difference in terms of median age, menopausal status, positivity of hormonal receptors and educational level. Conclusions: Our assessment of epidemiologic transition showed a reduction of clinco-pathological stage of IBC, keeping the same characteristics as compared to Tunisian historical series over a period of 14 years. Features seem to be different in Arab-American patients, probably related to migration, "occidentalization" of life style and improvement in socio-economic level.

• The Journal of the Korea Contents Association
• /
• v.7 no.6
• /
• pp.22-30
• /
• 2007

Most real word systems such as world economy, stock market, and medical applications, contain a series of dynamic and complex phenomena. One of common methods to understand these systems is to build a model and analyze the behavior of the system. In this paper, we investigated methods for best clustering over time series data. As a first step for clustering, BIC (Bayesian Information Criterion) approximation is used to determine the number of clusters. A search technique to improve clustering efficiency is also suggested by analyzing the relationship between data size and BIC values. For clustering, two methods, model-based and similarity based methods, are analyzed and compared. A number of experiments have been performed to check its validity using real data(stock price). BIC approximation measure has been confirmed that it suggests best number of clusters through experiments provided that the number of data is relatively large. It is also confirmed that the model-based clustering produces more reliable clustering than similarity based ones.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.18 no.6
• /
• pp.1-10
• /
• 2014

In this study, thirteen reinforced concrete beams, ground granulated blast furnace slag, replacing recycled coarse aggregate with PVA fiber (BSPG series) and recycled coarse aggregate with hybrid fiber ($BSPGR_1$, $BSPGR_2$ series), and standard specimen (BSS) were constructed and tested under monotonic loading. Experimental programs were carried out to improve and evaluate the Structural performance of such test specimens, such as the load-displacement, the failure mode, and the maximum load carrying capacity. All the specimens were modeled in 1/2 scale-down size. Test results showed that test specimens ($BSPGR_1$, $BSPGR_2$ series) was increased the compressive strength by 13%, the maximum load carrying capacity by 4~21% and the ductility capacity by 4~28% in comparison with the standard specimen (BSS). And the specimens ($BSPGR_1$, $BSPGR_2$ series) showed enough ductile behavior and stable flexural failure.