• Journal of the Korea Concrete Institute
• /
• v.18 no.1 s.91
• /
• pp.13-19
• /
• 2006

This paper reports the test results for shrinkage properties of low shrinkage high performance concrete developed by the authors depending on specimen size and constraint of reinforcing bar. As properties in fresh concrete low shrinkage high performance concrete(LSHPC) combined with expansive additives and shrinkage reducing admixture resulted in increase SP dosage due to loss of fluidity compared with that of control mixture concrete, while the dosage of AE agent was decreased. LSHPC exhibited higher compressive and tensile strength than control mixture concrete. For the effect of specimen size, an increase in specimen size led to a reduction of drying shrinkage. However, it was found that the autogenous shrinkage was not affected by the specimen size and measuring method. For constraint condition, an increase in the ratio of reinforcing bar caused the slight reduction in the strain of reinforcing bar, while it increased the autogenous shrinkage stress. It was seen that LSHPC was effective to reduce autogenous shrinkage by as much as 70% compared with control mixture high performance concrete.

• Korean Journal of Materials Research
• /
• v.9 no.3
• /
• pp.322-326
• /
• 1999

In this study, cold-rolling and appropriate annealing was adopted for the grain refining of Cu-26.65Zn-4. 05Al-0.31Ti(wt%) shape memory alloy. For the cold deformation of this alloy the ducti1e $\alpha$-phase must be contained. After heat treatment at $550^{\circ}C$ the $(\alpha+$\beta)$-dual phase with 40vol.% $\alpha$-phase was obtained which could be rolled at room temperature. This alloy was cold rolled into a final thickness of 1.0mm with total reduction degrees of 70% and 90%. The rolled sheets were betanized at $800^{\circ}C$ for various times, then quenched into ice water. The grain size of co]d rolled samples were $60~80\mu\textrm{m}$ which is much smaller comparing with the hot-rolled samples. And the 90% rolled sample showed smaller grain size than the case of the 70% rolled one. The small grain size had influence on the phase transformation temperatures and stabilization of the austenitic phases.

• Membrane Journal
• /
• v.14 no.3
• /
• pp.218-229
• /
• 2004

We prepared monodispersed calcium alginate microspheres by controlling various conditions of emulsification procedure using a lab-scale batch type membrane emulsification system equipped with SPG (Shirasu porous glass) tubular membranes. We determined the effects of process parameters of membrane emulsification (ratio of dispersed phase to continuous phase, alginate concentration, emulsifier concentration, type and concentration of stabilizer, transmembrane pressure, concentration of crosslinking agent, stirring speed and membrane pore size) on the mean size and size distribution of alginate microspheres. The increase of the ratio of dispersed phase to continuous phase, transmembrane pressure and alginate concentration led to the increase in the mean size of alginate microspheres. On the contrary, the increase in emulsifier concentration, stirring speed of the continuous phase and concentration of the crosslinking agent caused the reduction of the mean size of microspheres. Through controlling these parameters, monodisperse alginate microspheres with about $6{\mu}{\textrm{m}}$ of the mean size and 1.1 of the size distribution value were finally prepared in case of the using SPC membrane with the pore size of $2.9{\mu}{\textrm{m}}$.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.7 no.3
• /
• pp.373-378
• /
• 2006

One of the biggest problems that should be solved in present RFID systems is a reduction of identification efficiency by the collision of singals between different tags. As the number of tags, which should be identified, increases over the size of allocated round, more slots experiences the collision between them. It can causes generation of tag collision assigning the fixed round size and so, allocated round size should be regulated properly. This paper proposes the algorithm which can reduce collision between tags, and allocate specific round size dynamically for efficient tag identification. After each round is finished, the reader allocates the round size dynamically using the collision information of the slot. All collision informations of the slot consists of the number of slots which came into conflict, tags which were realized properly without any conflictions and empty slots. We used slotted aloha algorithm as the collision detection algorithm and finally, checked that this could be used very usefully when this algorithm which was proposed effectively could not know how many number of tags were exisisted through the simulation in advance.

• ALGAE
• /
• v.28 no.4
• /
• pp.365-369
• /
• 2013

The objective of this study was to determine the optimal blade size and timing to transplant seed-stock of Ecklonia cava Kjellman onto the reef structure. We used the modified artificial stepped reef structure. A total of 14 units (3.0 m length ${\times}$ 3.5 m width ${\times}$ 1.1 m height) were deployed 7-8 m deep under the water to examine the optimal blade size and timing to transplant seed-stock of E. cava onto the structures. Sporophytes of E. cava <1 cm in length were all died within 1 month of transplantation. The blades of 5-10 cm in length which were transplanted in March 2007 survived and grew well on the artificial reefs. Growth rates of 5-10 cm size class were higher than those of longer blade sporophytes (20-30 cm size class, transplanted in April) while the survival rates showed no difference between the classes of blade size. Both classes of 5-10 and 20-30 cm in length grew until July, and a reduction in size had occurred in September. These results indicate the importance of the blade size of E. cava and timing for successful transplantation of the seaweed on artificial reef structures.

• Journal of the Korea Safety Management & Science
• /
• v.10 no.2
• /
• pp.133-141
• /
• 2008

The need for total enterprise management that covers from accepting orders, design, cost, procurement, manufacture, and delivery has been recently raised in order for efficient project management of small and medium size plant construction enterprises. This trend is reflected in the introduction of EPM(Enterprise Project Management) solutions by some shipbuilding enterprises and large construction corporations. In step with the trend, small and medium size plant construction enterprises are enabled to provide knowledge base in terms of reducing cost and production period and managing portfolio for accepting orders and attaining contract by inducing customized EPM This study presents a design of customized EPM based on a case study of a company. It exhibits a collaborative/collaboration resource-supply model which can be universally applied to small and medium size job-order production enterprises. The research discusses that under the assumption that information is shared internally between departments on planning, supply, manufacture, and quality control in order to create collaborative environment and close participation is created externally between suppliers and orderers, productivity can be improved in cost reduction through planning efficient collaborative supply model.

• Journal of Surface Science and Engineering
• /
• v.42 no.5
• /
• pp.227-231
• /
• 2009

The niobium capacitor showed somewhat more unstable characteristics than the commercial tantalum capacitors, but is nonetheless considered applicable as a future substitute for tantalum capacitors. In this study, niobium powder was fabricated by metallothermic reduction process using $K_2NbF_7$ as the raw materials, KCl and KF as the diluents and Na as the reducing agent. The niobium particle size greatly decreased from 0.7um to 0.2 um as the amount of diluent increased. However if a higher surface area of powder is required, more diluents need to be used in the said method in order to produce niobium powder. The niobium powder morphology and particle size are very sensitive to a amount of sodium excess. The particle size of niobium powder increased with a increasing amount of sodium excess. When more diluent and sodium are used, the niobium powder will be contaminated with more impurities such as Fe, Cr, Ni so on.

• Journal of Applied Reliability
• /
• v.14 no.1
• /
• pp.11-19
• /
• 2014

A colloidal silica slurry has been manufactured by mixing nano silica powders having different grain size to improve the reliability of Sapphire wafer CMP process. The main reliability problem of CMP process such as the breaking of wafer can be prevented by reducing the size of particles in a slurry. While existing commercial colloidal silica slurries are usually made of single grain size silica powder of about 120nm, in the present study 40nm and 100nm silica powders are mixed to achieve a similar removal rate. The new colloidal silica slurry showed wafer removal rate of $3.04{\mu}m/120min$ while that of a commercial colloidal silica slurry was $3.03{\mu}m/120min$. The roughness was less than $4{\AA}$ and scratch was 0. It is also expected that the reduction of the size of nano silica particles can improve the dispersion stability and prolong the useful life of the slurry.

• Korean Journal of Biological Psychiatry
• /
• v.19 no.4
• /
• pp.211-218
• /
• 2012

Objectives Body image distortion is found in eating disorder and obesity and there are some evidence that schizophrenia is associated with body image distortion. This study sought to find whether schizophrenic patients report more body image distortion than healthy individuals and whether it is related with symptomatology. Methods A total of 88 inpatients with schizophrenia and 88 healthy controls were recruited. Weight, height, and body image accuracy were assessed in all participants, and assessment of mood, psychotic symptom severity and self-esteem, and personal and social performance scale were conducted. Results The patients with schizophrenia had higher Body Mass Index (p < 0. 001) and underestimated their body size more than controls (26.14% vs. 5.13%, p < 0.001). Multiple regression analysis showed that lower depressive symptoms and higher scores of general psychopathology predicted underestimation of body size. Conclusion Weight gain and metabolic syndrome are common adverse events of pharmacological treatment of schizophrenia. Thus, underestimation of body size among patients with schizophrenia may interfere with effort to lose weight or seek weight reduction programs. Clinicians need to consider possible unterestimation of underestimation of body size in patients whose general symptomatology is severe.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.31 no.7 s.262
• /
• pp.596-603
• /
• 2007

As increasing interest for soot emission. etc in combustion systems, various studies are being carried out for the reduction and measurement techniques of soot. Especially, laser induced incandescence is the useful measurement technique which has distinguished spatial and temporal resolution for primary particle size, volume fraction and aggregated particle size etc. Time resolved laser induced incandescence is the technique for measuring primary particle size that is decided to solve the signal decay rate which is related to the cooling behavior of heated particle by pulsed laser. The cooling behavior of heated particle is able to represent the heat and mass transfer model which are involved constants of soot property for surround gas temperature on the our previous work. In this study, it is applied to the time-dependence thermodynamic properties for soot temperature instead of constants of soot property for surround gas temperature and compared two different model results.