• 한국분말재료학회지
• /
• 제19권2호
• /
• pp.117-121
• /
• 2012

Tool steels serve a large range of applications including hot and cold workings of metals and injection mouldings of plastics or light alloys. The high speed steels (HSS) are specifically used as cutting tools and wear parts because it has high strength, wear resistance and hardness along with appreciable toughness and fatigue resistance. From the view of HSS microstructure, it can be described as metallic matrix composites formed by a ferrous with a dispersion of hard and wear resistant carbides. The experimental specimens were manufactured using the PIM with T42 powders (50~80 vol.%) and polymer (20~50 vol.%). The green parts were debinded in n-hexane solution at $60^{\circ}C$ for 8 hours and thermal debinded at an $N_2-H_2$ mixed gas atmosphere for 8 hours. Specimens were sintered in high vacuum ($10^{-5}$ Torr) and various temperatures.

• 한국세라믹학회지
• /
• 제36권1호
• /
• pp.89-96
• /
• 1999

석고몰드의 단점을 극복할 수 있는 다공질 알루미나 몰드의 제조저건을 확립하였다. 다공질 알루미나 몰드의 제조를 위해 활성탄의 질량비에 따라 조성비를 달리하여 첨가한 후, ESA와 유동특성 등을 조하삼으로써 안정된 이상 슬러리를 제조하였으며, 이를 석고몰드에 캐스팅하여 얻은 원통형 알루미나 몰드를 사용하여 활성탄의 양과 소결온도에 따른 수축율 변화와 마모에 대한 저항성을 측정하였다. 다공질 알루미나 몰드의 소결에서는 비수축 소결구인 표면확산에 의해 입자간 넥 강도의 증진을 통한 몰드의 강도 증진을 도모하는 것이 바람직하며, 이를 위해 1,00$0^{\circ}C$이하에서 유지시간의 변화에 따른 열역학적 방법, 1,00$0^{\circ}C$이상의 온도에서 알루미나의 수축을 억제하면서 빠른 승온속도를 열처리온도에 따른 동역학적 방법과 이 두가지 방법을 혼합하는 방법 등으로 구분하여 다동질 알루미나 몰드의 소결조건을 분석하였다. 위 방법들에 대한 다공질 알루미나 몰드의 캐스팅 특성을 분석한 결과, 복합 소결법이 최적임을 알수 있었다. 제조된 다공질 알루미나 몰드의 비교적 높은 강도를 보였으며, 석고몰드레 비해 빠른 건조시간, 산, 염기에 대한 내식성 및 캐스팅 특성이 우수하였다.

• 한국분말재료학회지
• /
• 제15권2호
• /
• pp.95-100
• /
• 2008

The investigation is to modify the mechanical and chemical properties of Mg alloys using a combination of rapid solidification and surface treatment. As the first approach, $Mg_{95}Zn_{4.3}Y_{0.7}$ was gas atomized and pressure sintered by spark plasma sintering process (SPS), showing much finer microstructure and higher strength than the alloys as cast. Further modification was performed by treating the surface of PM Mg specimen using Plasma electrolytic oxidation (PEO) process. During the PEO processing, MgO layer was initiated to form on the surface of Mg powder compacts, and the thickness and the density of MgO layer were varied with the reaction time. The thickening rate became low with the reaction time due to the limited diffusion rate of Mg ions. The surface morphology, corrosion behavior and wear resistance were also discussed.

• 한국분말재료학회지
• /
• 제4권4호
• /
• pp.243-251
• /
• 1997

Engine valve-shaped TiAl-Mn intermetallics containing 43.5 to 47.5at%Al (Mn/Al=0.036) are successively fabricated by reactive sintering the elemental powder mixtures near-net shaped by extrusion and die forging. A duplex structure consisted of lamellar grains and equiaxed $\gamma$ grains is developed for all compositions, and the areal fraction of the lamellar grains(or equiaxed $\gamma$ grains) decreases (or increases) with increasing Al content. As Al content increased, the elongation increases with accompanying decrease in yield strength and ultimate tensile strength at both room temperature and 80$0^{\circ}C$. This indicates that the suitable composition is Ti-45at%Al-1.6at%Mn in considering the balance of ambient and elevated tensile properties. The reactive-sintered Ti-45Al-1.6Mn alloy shows superior oxidation resistance not only to the plasma arc melted one but also to the heat resistance steel STR35(representative exhaust valve head material for automotive engine). The reactive-sintered Ti-45Al-1.6Mn alloy coated with an oxidizing scale exhibits a better wear resistance than induction hardened martensitic steel STR11(representative exhaust valve tip material for automotive engine).

• 한국분말재료학회지
• /
• 제22권3호
• /
• pp.157-162
• /
• 2015

SKD11(ASTM D2) tool steel is a versatile high-carbon, high-chromium, air-hardening tool steel that is characterized by a relatively high attainable hardness and numerous, large, chromium rich alloy carbide in the microstructure. SKD11 tool steel provides an effective combination of wear resistance and toughness, tool performance, price, and a wide variety of product forms. Adding of CNTs increased the performance of mechanical properties more. 1, 3 vol.% CNTs was dispersed in SKD11 matrix by mechanical alloying. SKD11 carbon nanocomposite powder was sintered by spark plasma sintering process. FE-SEM, HR-TEM and Raman analysis were carried out SKD11 carbon nanocomposites.

• 한국결정성장학회지
• /
• 제8권1호
• /
• pp.111-116
• /
• 1998

질화규소는 고경도, 고인성 세라믹 재료이기 때문에, 기계적 가공성은 매우 나쁘며, 또한 질화규소는 높은 전기 저항을 갖는다. 매우 높은 전기저항을 띠는 질화규소에 30wt% 이상의 TiN 분말이 첨가되었을 때 전도성 세라믹 복합체가 된다. 높은 전기 전도도를 가질 때 세라믹을 방전가공방법(EDM)을 이용하여 정밀한 가공을 할 수 있다. 높은 전기 전도도를 갖는 $Si_3N_4-TiN$ 세라믹 복합체는 EDM 방법을 이용하여 금속 가공 tool을 만드는데 이용되며, 이러한 tool 재료들은 산화뿐만 아니라 심각한 마모문제를 갖는다. 상압소결후 post HIP 소결방법으로 $Si_3N_4-TiN$ 복합체를 만들었으며, TiN의 양의 변화에 따른 $Si_3N_4$ 복합체의 마모특성을 상온의 대기중에서 조사하였다. 경도, 파괴인성, 강도값을 마모량과 비교하였다. 마모흔의 SEM 관찰로 $Si_3N_4-TiN$ 복합체의 마모기구를 설명하였다.

• 대한금속재료학회지
• /
• 제47권8호
• /
• pp.508-515
• /
• 2009

Ti-6Al-4V biomaterial is widely used as a bone alternative. However, Ti-6Al-4V ELI alloy suffers from numerous problems such as a high elastic modulus and high toxicity. Therefore, non-toxic biomaterials with low elastic moduli need to be developed. Ti-HA(hydroxyapatite) composites were fabricated in the present work by pulsed current activated sintering (PCAS) at $1000^{\circ}C$ under 60 MPa using mixed Ti and HA powders. The effects of HA content on the physical and mechanical properties of the sintered Ti-HA composites have been investigated. X-ray diffraction(XRD) analysis of the Ti-HA composites, including Ti-40 wt%HA in particular, revealed new phases, $Ti_{2}O$, CaO, $CaTiO_3$, and TixPy, formed by chemical reactions between Ti and HA during sintering. The hardness of the Ti-HA composites decreased with an increase in HA content. The corrosion resistance of these composites was observed to be an excellent candidate as a commercial Ti-6Al-4 V ELI alloy. A Ti-5 wt%HA composite fabricated by PCAS is recommended as a new biomaterial, because it offers good corrosion resistance, compressive strength, wear resistance, and biocompatibility, and a low Young's modulus.

• 한국분말재료학회지
• /
• 제20권4호
• /
• pp.291-296
• /
• 2013

SKD11 (ASTM D2) tool steel is a versatile high-carbon, high-chromium, air-hardening tool steel that is characterized by a relatively high attainable hardness and numerous, large, chromium rich alloy carbide in the microstructure. SKD11 tool steel provides an effective combination of wear resistance and toughness, tool performance, price, and a wide variety of product forms. The CNTs was good additives to improve the mechanical properties of metal. In this study, 1, 3 vol% CNTs was dispersed in SKD11 matrix by mechanical alloying. The SKD11+ CNT hybrid nanocomposites were investigated by FE-SEM, particle size distribution, hardness and wear resistance. The CNT was well dispersed in the SKD11 matrix and the mechanical properties of the composite were improved by CNTs addition. It shows good feasibility as cold work die tool.

• 한국세라믹학회지
• /
• 제31권11호
• /
• pp.1307-1314
• /
• 1994

The aim of this work is to show the way of manufacturing the SiC mechanical seal at the low temperature of 130$0^{\circ}C$ using clay and frit as source of secondary phase. $\alpha$-SiC and $\beta$-SiC powder which showed different distribution of particle were used as starting materials, i.e. average particle size of $\alpha$-SiC was larger than that of $\beta$-SiC. The mechanical and tribological properties of two groups of specimen, i.e. one contained mainly larger $\alpha$-SiC powder and the other mainly fine particle $\beta$-SiC, were measured. The specimen consisted of larger $\alpha$-SiC exhibited lower density flexural strength and wear resistance is comparison with these of sample containning mainly $\beta$-SiC . This difference could be originated from the dependence of capillary force on the particle size. For the larger SiC particle, the liquid phase may not fill the whole pores during sintering, due to low capillary force, whereas the liquid phase can infiltrate into the small ores surrounded small $\beta$-SiC particle. Thus, the course of high flexural strength and high wear resistance of specimen prepared using small particles can be explaced from the easy infiltration of liquid phase.

• 한국기계가공학회지
• /
• 제16권1호
• /
• pp.149-156
• /
• 2017

Graphene nanoplatelet (GNP)-reinforced alumina ($Al_2O_3$) is a promising material for micro-partapplications, particularly micro-nozzle shapes, because of its excellent wearresistance. In this study, a $Al_2O_3$/GNPcomposite with 15 vol% graphene nanoplatelets (GNP) was highly densified and fabricated via spark plasma sintering for micro-electrical discharge drilling (Micro-ED drilling) and the wear resistance property of the composite is evaluated via the ball-on-disk method. In addition, the diameter and shape of the micro-electrodes machined by wire electrical discharge grinding (WEDG), block electrical discharge grinding (BEDG), and new linear block moving electrical discharge grinding (LBMEDG) methods are systematically compared and analyzed to observe the micro-hole machining in the micro-ED drilling of the $Al_2O_3$/15vol% GNP composite.