• 한국분말재료학회지
• /
• 제8권2호
• /
• pp.110-116
• /
• 2001

Abstract To investigate the effect of mechanical alloying process to thermoelectric properties of PbTe sintered body, Pb-Te mixed powder with Pb : Te : 1 : 1 composition was mechanically alloyed using tumbler-ball mill. Thermoelectric properties of the sintered body were evaluated by measuring of the Seebeck coefficient and specific electric resistivity from the room temperature to 50$0^{\circ}C$. Sintered body of only mechanically alloyed PbTe powder showed p-type behavior at the room temperature, and occurred type transition from p-type to n-type at about 30$0^{\circ}C$. PbTe sintered body which was fabricated using heat treated powder in $H_2$ atmosphere after mechanical alloying showed stable n-type behavior under 50$0^{\circ}C$. N-type PbTe sintered body fabricated by mechanical alloying process had 4 times higher power factor than that fabricated by the melt-crushing process. Application of a mechanical alloying process to fabricate of n-type PbTe thermoelectric material seemed to be useful to increase the power factor of PbTe sintered body.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1995년도 춘계학술대회 논문집
• /
• pp.33-38
• /
• 1995

In this study, unsistered, pre-sintered and sintered low purity alumina ceramics were machined with various tools to clarify the machniability, the optimum tool materials and the optimum tool materials and the optimum cutting conditions. The maon conclusions obtained were as follows. (1) Machined withalloy steel tool, the machinabilty of te pre-sintered ceramics becomes better with the decrease of pre-sintering temperature, but that of unsintered ceramics(white body) was extremely poor. (2) In the case of carbide tool K01, the tool life in machining white body was the longest, and the machinabilty of pre-sintered ceramics becomes poorer with the increase of the pre-sintering temperature. (3) In the case of ceramic tool, the 10000-1100 .deg. C pre-sintered ceramics showed te best machinability within a certain cutting speed range. So far as dry machining, the above combination and conditions showed the highest productivity. (4) When the pre-sintered ceramics were wet machined withsintered diamond tool, the tool life becomes extremelylong, and higher cutting speed can be can be used than in the case offull-sintered ceramics. The productivity of wet cutting is much higher than that ofdry cutting.

• 한국세라믹학회지
• /
• 제38권3호
• /
• pp.212-217
• /
• 2001

The influence of granules characteristics and compaction pressure on the microstructure and mechanical properties of sintered as a function of slurry dispersion state. The characteristics and the compaction behavior of the spray dried alumina granules considerably affected the microstructure as well as the mechanical properties of the sintered body. In the green bodies formed with granules prepared with a dispersed slurry, the granules with dimple clearly existed and caused pore defects in sintered body. These dimples were clearly present even in the green body prepared at 180 MPa. The pores between the granules were not removed during pressing and sintering, and remained in the sintered body. In contrast, in the granules fabricated from a flocculated slurry, the destroy of granules at the contact points was observed with increasing pressure. Sintered bodies fabricated with fewer defects showed strength increase. For the sample fabricated with flocculated slurry, the pores at the boundaries of granules were small and more irregular shape compared with those of dispersed slurry.

• 한국세라믹학회지
• /
• 제35권1호
• /
• pp.66-78
• /
• 1998

the microstructure and mechanical properties of seeded and ball-milled dry gels prepared by boehmite sol-gel method were discussed. The densification of seeded gels was improved with increasing seed content namely the number of seed The number of seed was 1.09, 3.35, 5.72${\times}$1012/cm3 boehmite when seeded with 1, 3, 5wt% respectively The ball milled gel contained about 0.5wt% seed and the number of seed was 4.72${\times}$1012/cm3 boehmite. The sintered density of 5wt% seeded gel was below 80% when sintered at 1300$^{\circ}C$ for 1h. On the other hand that of ball milled gel was very improved and reached to 97% In the case of 3wt% seeded gels the density over 97% was attained when sintered at 1500$^{\circ}C$for 1h. and the grain of the sintered body was several micrometers in size. However the sintered body of ball milled gel showed grain size of submicrometer when sintered at 1300$^{\circ}C$ for 1h. And this specimen showed highest harness value of 1900kg/mm2 The fracture toughness increased with increasing sintering temperature. The sintered body of ball milled gel showed the largest grain size and the highest fracture toughness without regard to sint-ering temperature.

• 한국분말재료학회지
• /
• 제7권1호
• /
• pp.6-11
• /
• 2000

Two kinds of Bi2Te3 powders, pure Bi2Te3/2vol.%ZrO2, have been prepared by a mechanical grinding process process. Effect of mixing of the powders on thermoelectric of the sintered body has been investigated by measuring Seebeck Coeffcient, specific electric resistivity and thermal conductivity. With an increase in the weight fraction of the Bi2Te3/2vol.%ZrO2 powder from 0 to 40wt.%. Especially, the figure of merit of the mixedBi2Te3 sintered body increases and thereafter dedreases above 40wt.%. Especially. the figure of merit of the mixed Bi2Te3 sintered bodies with mixing of Bi2Te3/2vol.%ZrO2 powder increased about 1.3time in comparison with the value of the specimen before mixing. Mixing of two kinds of Bi2Te3 powders which have different theramal and electric propertries with each other seemed to be useful methob to increase the figure of merit of Bi2Te3 sintered body.

• 한국분말재료학회지
• /
• 제8권4호
• /
• pp.239-244
• /
• 2001

To investigate the effect of process parameters on selective laser sintering of Cu/polyamide mixed powder, Cu/polyamide mixed powder was sintered by selective laser with changing laser power and scanning speed. The properties of sintered body were evaluated by measuring the density and tensile strength, and analysis of XRD, FT-Raman and microstructure. With an increase in the laser power, the density and ultimate tensile strength of sintered Cu/polyamide body increase and then decrease. The maximum values of the density and ultimate tensile strength were decreased with increasing laser scanning speed. These changes were concerned with the difference of irradiation energy of laser into the powder layer. It was considered that the change of the mechanical property of the sintered body with irradiation energy of laser is due to the changes of amount of copper particle and property of polyamide.

• 한국세라믹학회지
• /
• 제37권5호
• /
• pp.511-515
• /
• 2000

The effect of Ba2+ ion dissolution with different pH and amount of PAA on microstructural changes of green and sintered bodies and its electrical properties was studied in aqueous nano-size BaTiO3 slurry system. The dissolution of Ba2+ was least at strong base, pH 10.8 and by addition of amount of 0.15 wt% PAA. The green body with the lowest of dissolution of Ba2+ at pH 10.8 and 0.15 wt% PAA had minimum values of average pore size, 40nm and shown high increase of sintered density. The compact sintered at 125$0^{\circ}C$ for 2 hr with highest Ba2+ dissolution had low density and dielectric constant due to abnormal grian growth. However, the sintered body with the lowest Ba2+ dissolution had high sintered density and then shown high dielectric constant.

• 한국분말재료학회지
• /
• 제18권4호
• /
• pp.365-371
• /
• 2011

In this study, gradient porous Al-Cu sintered body was fabricated by powder metallurgy processing. Al-Cu powder mixtures were prepared by low energy ball milling with various milling time. After ball milling for 3h, the shape of powder mixtures changed to spherical type with size of 100~500 ${\mu}m$. Subsequently, Al-Cu powder mixtures were classified (under 150, 150~300 and over 300 ${\mu}m$) and compacted (20, 50 and 100 MPa). Then, they were sintered at $600^{\circ}C$ for various holding time (10, 30, 60 and 120 min) in $N_2$ atmosphere. The sintered bodies had 32~45% of porosity. As a result, the optimum holding time was determined to be 60 min at $600^{\circ}C$ and sintered bodies with various porosity were obtained by controlling the compacting pressure.

• 한국분말재료학회지
• /
• 제19권4호
• /
• pp.285-290
• /
• 2012

The present study was focused on the analysis of the electric and thermal properties of spark plasma sintered $Bi_{0.5}Sb_{1.5}Te_3$ thermoelectric material. The crystal structure, microstructure, electric and thermal properties of the sintered body were evaluated by measuring XRD, SEM, electric resistivity, Hall effect and thermal conductivity. The $Bi_{0.5}Sb_{1.5}Te_3$ sintered body showed anisotropic crystal structure. The c-axis of the $Bi_{0.5}Sb_{1.5}Te_3$ crystal aligned in a parallel direction with applied pressure during spark plasma sintering. The degree of the crystal alignment increased with increasing sintering temperature and sintering time. The electric resistivity and thermal conductivity of the $Bi_{0.5}Sb_{1.5}Te_3$ sintered body showed anisotropic characteristics result from crystal alignment.

• 한국재료학회지
• /
• 제1권4호
• /
• pp.198-205
• /
• 1991

$Fe_2O_3,\;Al_2O_3,\;TiO_2$ 및 Si분말을 사용하여 고상반응법으로 써어미스터 소결체를 합성하였다. 합성된 소결체의 조식특성을 SEM으로 조사하고, 액체항온조에서 $-50~+50^{\circ}C$ 온도영역에서의 측정 결과 $\beta$상수가 972~4005K의 값을 갖는 써어미스터 소결체를 얻었다. 이 소결체는 고공기온측정을 위한 라디오존데용 온도센서로 사용될 수 있다.