• Proceedings of the KIEE Conference
• /
• 1992.07a
• /
• pp.503-505
• /
• 1992

This paper describes the optimization of design variables of SLIM using finite element method and SUMT(Sequential Unconstrained Minimization Technique). Thrust is taken as an objective function in order to maximize thrust under constant current drive, and seven independent design variables and nine constraints are chosen. As a result, $\tau$/g(pole pitch/airgap) and $\tau$/$d_{AL}$(pole pitch/aluminum depth) of good criteria in SLIM design are determined.

• Journal of Power System Engineering
• /
• v.3 no.4
• /
• pp.69-78
• /
• 1999

In the single-input and single-output system, the parameter of plant is scalar polynomial, but in the multiple input and multiple output, it accompanies, being matrix polynomial, the consideration of observable controlability index or problems non-commutation in matrix polynomial as well as degree, and it is more complex to deal with. Therefore, it is thought that a full research on the single-input and single-output system is not sufficient. This paper proposes that problems of minimum variance self-tuning regulator by using numerical calculation example of multivariable system and pole assignment self-tuning regulator.

• Proceedings of the Korean Society of Agricultural Engineers Conference
• /
• 2001.10a
• /
• pp.271-274
• /
• 2001

Experiments on the yield strength of pipe connectors made of metal wire, joint pins, pole pipes, multi span insertion joints, and T-clamp joints used in pipe houses were conducted. The strength of connections of a pipe connector made of metal wire was adequate but it had a big difference according to loading direction. The collapse load of pipes connected with a joint pin was lower than that of single pipes. Also experimental results showed that pole pipes for use in a part of frame buried under the ground were safe, and the strength of multi span insertion joints should be increased. The resistant moment of T-clamp was about 13.7% of a single pipe.

• Proceedings of the KIPE Conference
• /
• 2008.06a
• /
• pp.139-141
• /
• 2008

This paper presents a PID controller and PI-PI dual loop controller for a single-phase inverter. The control parameters of conventional controllers are very difficult to make. But parameters of controllers based on pole-assignment are easy to make. Simulation results are presented for the system under R-L load, no load and change reference voltage.

• Proceedings of the KIEE Conference
• /
• 1990.07a
• /
• pp.43-46
• /
• 1990

A general scheme for a discrete adaptive observer having exponetial weighting properties is presented for a single-input single-output linear system. In this scheme, all the past measurement data are weighted esponetially both with the weighting factor and the stable matrix F. This observer is then implemented in the design of an indirect adaptive pole placement contoller. To increase nemerical stability in getting the controller parameter, a recusive algorithm is introduced. It is shown that the overall control scheme is globally stable with the persistent excition

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.22 no.5
• /
• pp.17-23
• /
• 1985

This paper describes a method for the design of a self-tuning controller of single-input/single-output systems with system noises and obsrrvation noises. The method uses state-space techniques to assign the closed-loop system poles to desired locations, but the control law is made up of process input and output measurement values, so that state estimation is unnecessary. Also the difficulties of tracking of reference inputs in state.space pole-placing control are tackled by including the reference input in the cost function proposed by Beger.

• Journal of Institute of Control, Robotics and Systems
• /
• v.12 no.5
• /
• pp.505-508
• /
• 2006

This paper presents a new analytical approach for designing multiloop PI controllers for disturbance rejection in multivariable processes with time delay. The proposed method is based on IMC-PID design approach. To overcome a sluggish load response by dominant pole in the process, the IMC filter is modified to compensate the dominant pole effect. Based on the modified IMC filter, an analytical tuning rule for multiloop PI controller is driven by extending the generalized IMC-PID method for single input/single output (SISO) systems [1] to multi input/multi output (MIMO) systems. Simulation results show that the proposed method gives a satisfactory load performance as well as servo performance in the multiloop system.

• Journal of Sensor Science and Technology
• /
• v.20 no.2
• /
• pp.77-81
• /
• 2011

This paper presents a single-pole eight-throw(SP8T) switch based on proposed a radio-frequency(RF) microelectromechanical systems (MEMS) switches. The proposed switch was driven by a double stop(DS) comb drive, with a lateral resistive contact. Additionally, the proposed switch was designed to have tapered signal line and bi-directionally actuated. A forward actuation connects between signal lines and contact part, and the output becomes on-state. A reverse actuation connects between ground lines and contact part, and the output becomes off-state. The SP8T switch of 3-stage tree topology was developed based on an arrangement of the proposed RF MEMS switches. The developed SP8T switch had an actuation voltage of 12 V, an insertion loss of 1.3 dB, a return loss of 15.1 dB, and an isolation of 31.4 dB at 6 GHz.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.07a
• /
• pp.422-423
• /
• 2005

RF Micro switches is a miniature device or an array of integration devices and mechanical components and fabricated with Ie batch-processing techniques. RF Micro switches application area are in phased arrays and reconfigurable apertures for defence and telecommunication systems, switching network for satellite communication, and single-pole double throw switches for wireless application. Recently, RF Micro switches have been developed for the application to the milimeter wave system. RF Micro switches offer a substantilly higher performance than PIN diode or FET switches. In this paper, SPDT(single-pole-double-throw) switch are designed to use 10 GHz. Actuation voltage and displacement are simulated by tool.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.07b
• /
• pp.652-655
• /
• 2004

RF MEMS is a miniature device or an array of integration devices and mechanical components and fabricated with If batch-processing techniques. RF MEMS application area are in phased arrays and reconfigurable apertures for defence and telecommunication systems, switching network for satellite communication, and single-pole double throw switches for wireless application. Recently, RF MEMS switches have been developed for the application to the milimeter wave system. RF MEMS switches offer a substantilly higher performance than PM diode or FET switches. In this paper, SPDT(single-pole-double-throw) switch are designed to use 10 GHz. Actuation voltage and displacement are simulated by tool. And stress and distribution are simulated.