• Journal of the Semiconductor & Display Technology
• /
• v.12 no.2
• /
• pp.63-66
• /
• 2013

Carbon Nanotube have been proposed for use in various applications for electromechanical systems. Nano-electromechanical resonators which provide high frequency resolution and long energy storage time, play an important role in wide area fields of science and engineering. Using the control of tension in carbon nanotube, can be made the tunable resonator. In the study, we analysis the tunable frequency change of resonator by tension changes due to the rotation angles of the single-walled carbon nanotube resonator. The frequency characteristics of a resonator as a function of the rotation angle. The tension was found to decrease with increasing rotation angle, and therefore the resonance frequencies could be changed by controlling the single-walled carbon nanotube rotation angle. The resonance frequencies decreased with increasing angle, and when the rotation angle was greater than $60^{\circ}$, these changes were marked.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.21 no.12
• /
• pp.1432-1437
• /
• 2010

This paper proposes a new design method of bandpass filter with single dual-mode resonator. In the proposed method, a coupling coefficient between two resonators was obtained by considering a dual-mode resonator as two single resonators. Based on the obtained coupling coefficient, two resonant frequencies of dual-mode resonator were calculated and then arranged according to a transmission zero's location of required filter. To verify the proposed theory, two WLAN bandpass filters which have a transmission zero to a lower and an upper stopband repectively were designed and implemented.

• Journal of Sensor Science and Technology
• /
• v.31 no.2
• /
• pp.107-114
• /
• 2022

The effects of ring radius and coupling spacing on the free spectral range (FSR), full width at half maximum (FWHM), quality factor, and sensitivity of single-channel and add-drop channel slot ring resonators were systematically investigated using FIMMPROP and PICWAVE numerical software. The single-channel ring resonator exhibited better characteristics, namely, a wider FSR and narrower FWHM compared with the add-drop structure; thus, it was evaluated to be more suitable for biochemical sensors. The FSR, FWHM, quality factor, and sensitivity for a single channel ring resonator with a radius of 59.4 ㎛ and coupling gap of 0.5 ㎛ were 2.4 nm, 0.087 nm, 17677, and 550 [nm/RIU], respectively.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.9 no.8
• /
• pp.921-926
• /
• 2014

In this paper, the characteristics of inset fed microstrip antenna loaded with CSLR(complementary single loop resonator) are studied. Effective permeability parameters of the SLR unit cell is retrieved from simulated scattering parameters, and structure parameters of the SLR unit cell are selected so that effective permeability is negative value at the operating frequency. The optimized inset fed microstrip antenna loaded with SLR for a $3{\times}3$ array in the ground plane of a conventional patch antenna is designed and simulation results of return loss and radiation pattern are shown. At resonant frequency 2.82 GHz, the overall dimension of the proposed antenna is reduced by approximately 56.8% compared to the conventional inset fed antenna. Simulation results are obtained by 3D FEM solver(Ansoft's HFSS).

• Journal of the Korean Society for Precision Engineering
• /
• v.17 no.11
• /
• pp.81-87
• /
• 2000

A new resonator that is fabricated by single polysilicon layer process is presented. The resonator can move in two orthogonal direction on the plane parallel to the substrate. And the resonant frequencies of the two modes are intrinsically designed to be identical since the overall structure of the resonator is symmetric about the two directions of motion. Since the resonator ideally has two identical vibration mode, it can be applied to various micro-devices that requires multi DOF motion, especially to microgyroscopes. To investigate the feasibility of application of the resonator, dynamic model of the resonator including the nonlinear behavior of driving electrodes is derived and evaluated with the fabricated one, and the self-tuning characteristics are proved though experiments.

• ETRI Journal
• /
• v.33 no.2
• /
• pp.291-294
• /
• 2011

This letter proposes an open-ended waveguide antenna with a single split-ring resonator. In contrast to the waveguide antennas incorporating multiple rings reported in a previous study, which exhibited narrow bandwidth, the proposed antenna uses only one ring to achieve broader bandwidth while keeping the aperture small. A single ring has a relatively low quality factor compared to multiple rings. The simulated and measured fractional bandwidth was 4.13% and 4.03%, respectively, which is much broader than the fractional bandwidth of about 1% demonstrated in a previous study. This simple technique can be used in many applications that require small apertures including near-field probes and array elements.

• Journal of KSNVE
• /
• v.4 no.2
• /
• pp.209-219
• /
• 1994

Classical method calculates the resonance frequency of Helmholtz resonator by postulating that there is a moving mass in neck and a stiffness which expresses the compressibility of cavity. This has been widely accepted as reasonable to determine the resonant frequency, provided that the wave length of interest is longer that any length scale of resonater. Nevertheless, it has been often recognized that this classical method sometimes does not well predict the resonant frequency. This paper decribes the way in which the dynamics of resonator very often does care about the detail geometries of resonator; location of the neck, diameter ratio of the neck to that of cavitty, length of resonator compared with that of neck, etc. This rather unexpected observations have been proved theoretically; 3 dimensional analysis of acoustic wave equation, as well as experimentally by comparing the resonant frequencies, transmission loss, and insertion loss of resonator.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.52 no.12
• /
• pp.41-45
• /
• 2015

In this paper, the single port dual-band resonator for magnetic resonance wireless power transfer is proposed. The proposed dual-band resonator is consists of 20 turns spiral coil, a single loop, matching circuit, lumped elements, and a single port. The two sides of the matching circuit are connected to via holes. The spiral coil is operated at MF-band and single loop is operated at HF-band, respectively. We use two of the same structure resonators and simulated and the power transfer efficiency was calculated. The efficiency of simulation and measurement is above 60% at the MF and HF bands, and the distance is 100 mm.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.07a
• /
• pp.135-138
• /
• 2003

The circular cavity resonator which can measure the dielectric properties of dielectrics in the V-band($50GHz{\sim}75GHz$) frequency range was designed and fabricated. Exciting and detecting of the resonator is peformed by WR15 rectangular waveguides using Bethe's small hole coupling. The GaAs plate sample was used for the verification of the performance of the fabricated circular cavity resonator. In the measurement of GaAs single crystal using that resonator, the resonant frequency of the dominant $TE_{011}$ mode, the permittivity and $Q{\times}f_0$ were measured as 53.29GHz, 12.87 and 138,000, respectively.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2003.11a
• /
• pp.202-207
• /
• 2003

In the paper, the noise reduction characteristics of a double-gap resonator, which is installed inside an enclosed cavity and is composed of two air-gaps and two partition sheets, are introduced by theoretical analyses and experimets. Analysis for a simple, theoretical model reveals that the double-gap resonator is more effective than the single-gap resonator that consists of an air-gap and a partition sheet, in that the former requires a smaller space than the latter. Furthermore, this theoretical conclusion is verified by comparison experiments using an actually manufactured enclosed cavity, of which the boundary surfaces are made of thick, stiff panels that can be assumed as rigid walls.