• Journal of Korean Society of Steel Construction
• /
• v.26 no.5
• /
• pp.407-418
• /
• 2014

As a continuing work of previously conducted standard tension tests, full-scale flexural tests were conducted in this study to assess the structural performance the CJP groove welded joints connecting thick HSA800 plates. Two welding electrodes were available at the time of this experimental research; one was GMAW-based electrode A and the other FCAW-based electrode B. Three full-scale box-type beam specimens with single bevel- and V-groove CJP welded joints were fabricated from 60mm and 25mm thick HSA800 plates according to the AWS-prequalified groove welded joint details. In designing the specimens, all possible limit states like local and lateral torsional buckling were carefully controlled in order to induce flexural plastic yielding or eventual joint fracture. All the CJP joints made by both welding electrodes showed satisfactory performance and were able to transfer the tensile flange forces higher than that corresponding to the measured tensile strength of HSA800 flange plates. However, it should be noted that, during fabrication, serious concerns about the welding efficiency and workability of the GMAW-based electrode were raised by a certified welder. The fracture occurred at the unbeveled (or vertical) interface between the weldment and the base metal when the GMAW-based electrode was used in the single-bevel joint, implying the possibility of insufficient melting. Thus, the FCAW-based electrode B is again recommended as the choice of welding electrode for HSA800 plates. The limited test data of this study implies that the V-groove CJP joint should be used in favor of the single bevel CJP joint, if possible.

• Journal of Bio-Environment Control
• /
• v.14 no.1
• /
• pp.56-62
• /
• 2005

This study was conducted to investigate the effect of grafting methods on plug seedling quality, growth after transplanting, and yield of oriental melon that those seedlings were raised in the 32 hole plug tray for protected cultivation. Number of leaf and leaf area in approach grafting were higher until 15 days after grafting but lower on 20 days after grafting. Plant height, stem diameter and content of chlorophyll were nearly the same of each grafting methods on 20 days after grafting. Growth of top part, that is, plant height, leaf number, and leaf area on root removed single cotyledon ordinary splice grafting was the highest among the grafting methods. In the underground part, dry weight of root was high and T/R ratio was the lowest. Seedling quality of root removed single cotyledon ordinary splice grafting was the highest among grafting methods before transplanting. Plant height, number of leaf, leaf area and dry weight of root removed single cotyledon ordinary splice grafting in the growth of field were the highest on 30 days after grafting among grafting methods and days required for first flowering was also shorter, 38.4 days among grafting methods. But Fruit weight, content of soluble solids, fruit hardness, and color characteristics in fruit quality were insignificant among each grafting methods. Consequently, grafting methods influenced on the seedling quality, of oriental melon early growth after transplanting and yields. It was concluded that root removed single cotyledon ordinary splice grafting was the best methods in present study. It will be needed to convert grafting methods. Thus new grafting method should be applied.

• Journal of the Korean Society of Environmental Restoration Technology
• /
• v.5 no.2
• /
• pp.53-62
• /
• 2002

The objectives of this study were to understand the tolerance mechanism of woody plants to water stress and tolerance changes in relation to mycorrhizal formation. Lespedeza cyrtobotrya Miq. commonly used for erosion control in slopes were raised from seeds and transplanted to 120 plastic pots. Sixty pots received the top soil of a Fraxinus americana forest, while remaining 60 pots received the autoclaved top soil. The forest soil contained 1,200 spores per 100g of arbuscular endomycorrhizal fungus, mostly Glomus sp. The plants were raised outside with regular supply of water and mineral nutrients. Two kinds of water deficit treatment and a control were started at the middle of July : cyclic water deficit treatment with 3 cycles of sequential water stress at the point of xylem water potential of about -0.6, -0.6, and -1.7 MPa and recovery, and non-cyclic water deficit treatment with single water stress at about -1.5 MPa. The non-stressed plants received plenty of water throughout the period. In late August the plants were harvested for measurements of dry weight, N, P, carbohydrate contents, net photosynthesis and superoxide dismutase(SOD) activities. Both cyclic and non-cyclic water deficit treatments reduced dry weight by 60% and 40%, respectively, and reduced nitrogen absorption, while increased SOD activities. Water-stressed plants also showed increased carbohydrate contents in the leaves and lowered stomatal conductance. Mycorrhizal inoculation resulted in an average of 40% infection of roots and 2-3 times increase in P absorption in water-stressed as well as non-stressed plants. Mycorrhizal formation also increased shoot-root ratio. The results that SOD activities of water-stressed plants with mycorrhizal infection were significantly lower than those of non-mycorrhizal plants suggest the possibility of improvement of water-stressed condition by mycorrhizal formation. It was concluded that endomycorrhizal formation increased tolerance of Lespedeza cyrtobotrya seedlings to water stress.

• Korean Journal of Poultry Science
• /
• v.30 no.2
• /
• pp.113-118
• /
• 2003

In this study, broilers were raised up to 6 weeks of age in a single room to determine if different levels of dietary protein or addition of aluminum sulfate[alum, $Al_2$(SO$_4$)$_3$ㆍ14$H_2O$] to the litter affected growth performance, production of ammonia(NH$_3$) and soluble phosphorus(SP) content of the litter.The experimental treatments consisted of six treatments in a 2x3 factorial arrangements: T$_1$＝23% protein ＋ 0.2% alum to litter; T$_2$＝21% protein ＋ 0.2% alum to litter; T$_3$＝19% protein ＋ 0.2% alum to litter; T$_4$＝23% protein ＋ no alum; T$_{5}$＝21% protein ＋ no alum; T$_{6}$＝19% protein ＋ no alum. For broiler performance, there was no effect of alum addition to the litter, but the dietary protein levels significantly affected feed intake from days 22 to 42(P<0.05) and day 0 to 42(P< 0.05), weight gain during all periods(P<0.05 or 0.01), and feed:gain from day 0 to 21(P<0.05) and day 0 to 42(P<0.05). Alum addition to the litter did not affect body weight at 21 and 42 days, but dietary protein levels has a significant effect on it at both 21(P<0.0l) and 42 days(P<0.05). Alum addition only affected ammonia production at weeks 3(P

• Journal of Advanced Marine Engineering and Technology
• /
• v.40 no.9
• /
• pp.756-761
• /
• 2016

The objective of this study is to design and manufacture a fuel pump with the plunger diameter of 4 mm and stroke of 7 mm that can be mounted in a small single-cylinder four-stroke agricultural diesel engine, and to investigate the performance characteristics of the pump. The combustion pressure in a cylinder was reproduced by forming the back pressure of 1, 6, 11, 16 and 21 bar with a nitrogen gas in the home-manufactured modeling cylinder. In the experiment, the discharge pressure was measured at the spot of 1 cm away from the discharge port of a developed fuel pump. The delivery pressure and delivery flow rate were measured at the spot of 30 cm away from the discharge port of the pump, and the pump efficiency was calculated. The pump motor speed was changed from 600 to 800, 1000, 1200 and 1400 rpm. It is found that the delivery feed rate of fuel pump is increased as the rotational speed is raised, and is decreased as the back pressure, compression pressure in the cylinder, is increased. Also, the pump efficiency is reduced as the rotational speed and back pressure are increased.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.18 no.1
• /
• pp.4038-4051
• /
• 1976

This study was intended to provide the basic design creteria for the refrigerated storage, and to estimate the required optimum capacity of refrigerator for the different sizes and kinds of the existing fruit storage. The structural characteristics of the existing fruit storages in Pyungtaek-khun of Kyungki-do were surveyed. The average out-door air temperature during the expected storage life after harvesting, was obtained by analyzing the weather information. The heat transfer rates through the different models of storage walls were estimated. The refrigerating load required for different models of fruit storage was analyzed in the basis of out-door air temperature. The results obtained in this study are summarized as follows: 1. The fruit storages surveyed were constructed on-ground, under-ground and sub-ground type buildings. The majority of them being the on-ground buildings are mostly made of earth bricks with double walls. Rice hull was mostly used as the insulating materials for their walls and ceilings. About 42% of the buildings were with the horizontal ceiling, 22% with sloped ceiling, and about 36% without ceiling. About 60% of the storage buildings had floor without using insulated material. They were made of compacted earth. 2. There is no difference in heat transfer among six different types of double walls. The double wall, however, gives much less heat transfer than the single wall. Therefore, the double wall is recommended as the walls of the fruit storage on the point of heat transfer. Especially, in case of the single wall using concrete, the heat transfer is about five time of the double walls. It is evident that concrete is not proper wall material for the fruit storage without using special insulating material. 3. The heat transfer through the storage walls is in inverse proportion to the thickness of rice hull which is mostly used as the insulating material in the surveyed area. It is recommended that the thickness of rice hull used as the insulating material far storage wall is about 20cm in consideration of the decreasing rate of heat transfer and the available storage area. 4. The design refrigerating load for the on-ground storages having 20 pyung area is estimated in 4.07 to 4.16 ton refrigeration for double walls, and 5.23 to 6.97 ton refrigeration for single walls. During the long storage life, however, the average daily refrigerating load is ranged from 0.93 to 0.95 ton refrigeration for double walls, and from 1.15 to 1.47 ton refrigeration for single walls, respectively. 5. In case of single walls, 50.8 to 61.4 percent to total refrigerating load during the long storage life is caused by the heat transferred into the room space through walls, ceiling and floor. On the other hand, 39.1 to 40.7 percent is for the double walls. 6. The design and average daily refrigerating load increases in linear proportion to the size of storage area. As the size increases, the increasing rate of the refrigerating load is raised in proportion to the heat transfer rate of the wall. 7. The refrigerating load during the long storage life has close relationship to the out-door air temperature. The maximum refrigeration load is shown in later May, which is amounted to about 50 percent to the design refrigerating load. 8. It is noted that when the wall material having high heat transfer rate, such as the single wall made of concrete, is used, heating facilities are required for the period of later December to early February.

• Research in Plant Disease
• /
• v.20 no.1
• /
• pp.15-20
• /
• 2014

A rapid, user-friendly and simple immune-chromatographic dipstick kit named 'rapid immune-gold strip' (RIGS) kit was developed in a novel single strip format to detect on-site detection of Tomato spotted wilt virus (TSWV). Immunoglobulin G (IgG) from polyclonal antisera raised in rabbits against TSWV was purified through protein-A affinity chromatography and then the purified TSWV-IgG was conjugated to colloidal gold nano-particles which served as a test line on nitrocellulose membrane. Protein A that non-specifically binds to TSWV antibody was used as a control line on the same strip. The diagnosis process with the TSWV-RIGS involves simply grinding the suspect plant sample in a bag that contains the extraction buffer and inserting the strip the bag. Results can be seen in 2-5 minutes. The flow of the complexes of gold particles coated with TSWV-IgG and a crude sap from TSWV-infected pepper, tobacco and tomato plants resulted in intensive color formed on the test lines proportional to the concentrations of TSWV. The RIGS-TSWV kit did not show any cross-reactions against other tomato-infecting viruses unrelated to TSWV. These results indicate that the TSWV-RIGS kit is highly sensitive and is not required for laboratory training and experience prior to testing. The TSWV-RIGS kit is suitable for on-site detection of suspect TSWV-infected plants as well as for laboratory diagnosis.

• Parasites, Hosts and Diseases
• /
• v.55 no.4
• /
• pp.425-428
• /
• 2017

Human diphyllobothriasis is a parasitic disease caused by ingestion of larvae (plerocercoids) in raw or undercooked fish and commonly found in temperate areas. Rare cases were reported in tropical or subtropical areas especially in children. The first documented case of pediatric diphyllobothriasis in Taiwan had been reported 11 years ago. Here, we report another 8-year-old girl case who presented with a live noodle-like worm hanging down from her anus, with no other detectable symptoms. We pulled the worm out and found the strobila being 260 cm in length. Examination of gravid proglottids showed that they were wider than their lengths, containing an ovoid cirrus sac in the anterior side and the rosette-shaped uterus. Eggs extracted from the uterus were ovoid and operculated. Diphyllobothrium latum was confirmed by molecular analysis of the mitochondrial DNA cytochrome c oxidase subunit 1 (cox1) gene. The girl was treated with a single oral dose of praziquantel, and no eggs or proglottids were observed from her stool in the subsequent 3 months. The reemergence of human diphyllobothriasis in non-endemic countries is probably due to prevalent habit of eating imported raw fish from endemic areas. This pediatric case raised our concern that human diphyllobothriasis is likely underestimated because of unremarkable symptoms.

• Bulletin of the Korean Chemical Society
• /
• v.27 no.10
• /
• pp.1641-1647
• /
• 2006

Vibrational relaxation and competitive C-$H_{methyl}$ and C-$H_{ring}$ bond dissociations in vibrationally excited methylpyrazine in the collision with HF have been studied by use of classical trajectory procedures. The energy lost by the vibrationally excited methylpyrazine upon collision is not large and it increases slowly with increasing total vibrational energy content between 20,000 and 45,000 $cm^{-1}$. Above the energy content of 45,000 $cm^{-1}$, however, energy loss decreases. The temperature dependence of energy loss is negligible between 200 and 400 K, but above 45,000 $cm^{-1}$ the energy loss increases as the temperature is raised. Energy transfer to or from the excited methyl C-H bond occurs in strong collisions with HF, that is, relatively large amount of translational energy is transferred in a single step. On the other hand, energy transfer to the ring C-H bond occurs in a series of small steps. When the total energy content ET of methylpyrazine is sufficiently high, either or both C-H bonds can dissociate. The C-$H_{methyl}$ dissociation probability is higher than the C-$H_{ring}$ dissociation probability. The dissociation of the ring C-H bond is not the result of the direct intermolecular energy flow from the direct collision between the ring C-H and HF but the result of the intramolecular flow of energy from the methyl group to the ring C-H stretch.

• Journal of Environmental Health Sciences
• /
• v.43 no.4
• /
• pp.273-279
• /
• 2017

Objectives: Carbon nanotubes (CNTs) are next-generation industrial nanoparticles which possess excellent mechanical strength along with good thermal conductivity and electric properties. Given these characteristics, carbon nanotubes are being widely applied in various fields, including research and development. However, concerns have been raised over hazardous properties due to their similar fiber shape to asbestos. Recent studies have shown that CNTs pose potential hazards which may cause fibrosis and/or lung inflammation similarly to asbestos. Methods: After intratracheal instillation of SWCNTs and MWCNTs to rats, pulmonary surfactant (PS) of the SWCNTs and MWCNTs was measured and analyzed using bronchoalveolar lavage fluid collected from the lung. After a single intratracheal instillation of SWCNTs and MWCNTs, phospholipid predominantly showed a significant increase compared to the control group, while proteins exhibited a significant increase both three days and one week after instillation. Results: As a result of surface tension, MWCNTs showed a significant decrease three days after treatment compared to the control group. In the case of the total cell number three days after instillation, MWCNTs revealed a temporarily significant increase when compared to the control group. For PMN number, when compared to the control group, SWCNTs displayed a significant increase throughout the observation period, while MWCNTs showed a significant increase three days and three months after treatment. Conclusions: After exposure to CNTs, the total cell number and PNT number, which indicate inflammatory response, were significantly increased. Therefore, this study suggests fiber-shaped CNTs may have a harmful effect on the lungs.