• 한국방재학회 논문집
• /
• 제11권2호
• /
• pp.39-44
• /
• 2011

마이크로 스케일에서 다결정 재료의 소성 거동을 살펴볼 때, 결정의 geometrically necessary dislocation(GND) 효과에 의한 소성 구배(plastic gradient)를 고려하는 것은 재료의 소성 거동에 큰 영향을 줄 수 있다. 이러한 영향을 확인하기 위하여, 본 연구에서는 소성 구배의 영향을 고려한 다결정 고체(polycrystalline solids)의 거동을 유한요소해석을 이용하여 살펴보았다. 소성 구배의 영향을 살펴보기 위해 구배 경화 계수(gradient hardness coefficient)와 먼 거리 변형률에 대한 재료 길이 변수 (material length parameter)가 사용되었다. 재료 길이 변수에 의한 영향을 확인하기 위해, 재료 길이 변수의 차이에 따른 다결정 고체의 거동을 분석하였다. 또한 소성 구배 효과의 고려 및 재료 길이 변수에 따른 다결정 고체 내부에 위치한 단결정이 받는 영향을 살펴보았다. 재료 길이 변수에 따라 결정이 받는 영향을 비교하여, GND에 의한 다결정 고체 거동의 영향을 확인하였다.

• 한국세라믹학회지
• /
• 제37권5호
• /
• pp.425-431
• /
• 2000

Cobalt ferrite thin films on Corming glass substrate were fabricated by a sol-gel method. Cobalt ferrite thin films with the grain size of 20-35 nm and thickness of 50nm were obtained. Rapid thermal annealing (RTA) and Annealing processes were adopted for comparison of characteristics of the films. Coercivity values were changed with thermal condition and magnetization values were increased as a function of soaking time. With prolonged soaking time, however, it was decreased because of the diffusion of cations from the glass substrate. The RTA process in preparation of cobalt ferrite thin film was the effective way to prevent and to form a single spinel phase in reduced soaking time. The film heated at 600$^{\circ}C$ for 30 minutes by RTA had coercivity of 2,600 Oe, saturation magnetization 460 emu/㎤, and Mr$.$$\delta$ of 1.43 memu/$\textrm{cm}^2$.

• Advances in materials Research
• /
• 제2권1호
• /
• pp.1-13
• /
• 2013

Lead-free compound $(Na_{0.5}Bi_{0.5})(Zr_{0.75}Ti_{0.25})O_3$ was prepared using conventional ceramic technique at $1070^{\circ}C$/4h in air atmosphere. X-ray diffraction analysis showed the formation of single-phase orthorhombic structure. Permittivity data showed low temperature coefficient of capacitance ($T_{CC}{\approx}5%$) up to $100^{\circ}C$. Complex impedance studies indicated the presence of grain boundary effect, non-Debye type dielectric relaxation and evidences of a negative temperature coefficient of resistance. The ac conductivity data were used to evaluate the density of states at Fermi level and apparent activation energy of the compound.

• Architectural research
• /
• 제12권2호
• /
• pp.93-98
• /
• 2010

This paper describes a numerical method for estimating the elastic moduli of cement paste. The cement paste is modeled as a unit cell which consists of three components: the unhydrated cement grain, the gel, and the capillary pore. In the unit cell, the volume fractions of the constituents are quantified using a single kinetic function calculating the degree of hydration. The elastic moduli of cement paste are calculated from the total displacements of constituents when a uniform pressure is applied to the gel contact area. The cement paste is assumed to be a homogenous isotropic matrix. Numerical simulations were conducted through the finite element analysis of the three-dimensional periodic unit cell. The model predictions are compared with experimental results. The predicted trends are in good agreement with experimental observations. This approach and some of the results might also be relevant for other technical applications.

• 소성∙가공
• /
• 제4권2호
• /
• pp.159-168
• /
• 1995

The torsion tests in the range of $550~800^{\circ}C$, $5.0{\times}10^{-3}~5.0{\times}10^0/sec$ were performed to study the effects of strain rate$(\.{\varepsilon})$ and temperature(T) on the hot strength of Cu-Zn alloy. High temperature flow stresses of this alloy increased with increasing $\.{\varepsilon}$ and/or decreasing T, and than the more grain refinement could be obtained. The flow curves exhibited a peak followed by a steady steady state regime as a result of dynamic recrystallization. The hot strength dependence of $\.{\varepsilon}$ and T was described by a hyperbolic sine law, $\.{\varepsilon}=A(sinh0.017{\sigma})^4.81$exp(-216KJ/mol). Hot strength could be reduced at the arbitary condition, $\.{\varepsilon}$ and T, by constitutive parameter Z(Zenner-Hollomon parameter), $Z=A(sinh{\alpha}{\sigma})^n=\.{\varepsilon}$exp(Q/RT).

• 한국세라믹학회지
• /
• 제42권9호
• /
• pp.599-601
• /
• 2005

The coarsening process of two different $BaTiO_3$ single crystal seeds, one with a (111) double twin and the other without it, was investigated. Due to the presence of Twin Plane Reentrant Edge (TPRE), the coarsening rate of the twinned seed crystal was significantly higher than that without a twin. For the coarsening by the 2-dimensional nucleation and lateral growth, the energy barrier for nucleation at the TPRE was analyzed to be about a half compared with that at the terrace planes.

• 소성∙가공
• /
• 제21권3호
• /
• pp.164-171
• /
• 2012

This paper focuses on the development of a new SPD (severe plastic deformation) process named HCAE (half channel angular extrusion). HCAE technology is based on principled similar to ECAE, but imposes a larger amount and more effective plastic deformation on materials. The amount of shear deformation can be altered by varying the process parameters. Finite element analyses of HCAE were conducted in order to investigate the characteristics of deformation during HCAE and the simulated results show that the predicted value of imposed plastic strain in a single pass reaches 2.5.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2004년도 추계학술발표대회 개요집
• /
• pp.123-124
• /
• 2004

This study was investigated on the impact toughness and microstructure of welded metal and heat affected zone for Hi Nitrogen TiN Steel. With welding procedures, welding heat input applied were 30, 79 and 264 kJ/cm. TiN steel has shown very small prior austenite grain size for all the welding heat input applied, which was considered to result from the effect of TiN particles. In case of single SAW and EGW welding, the dilution rate of base metal into the weld was not high, resulting that there were no significant effects of base metal chemical composition on the mechanical properties of welds. However, TSAW with double Ypreparation carried very high dilution rate so that TiN steel has impaired the toughness of weld metal because N content in the weld was increased through the dilution of base metal.

• 한국분말재료학회지
• /
• 제8권2호
• /
• pp.104-109
• /
• 2001

The semiconducting ${\beta}-FeSi_2$ compound has been recognized as a thermoelectric material with excel-lent oxidation resistance and stable characteristics at elevated temperature. In the present work, we applied mechanical alloying(MA) technique to produce ${\beta}-FeSi_2$ compound using a mixture of elemental iron and silicon powders. The mechanical alloying was carried out using a Fritsch P-5 planetary mill under Ar gas atmosphere. The MA powders were characterized by the X-ray diffraction with Cu-K $\alpha$ radiation, thermal analysis and scanning electron microscopy. The single ${\beta}-FeSi_2$ phase has been obtained by mechanical alloying of $Fe_{33}Si_{67}$ mixture powders for 120 hrs or for 70 hrs coupled with the subsequent heat treatment up to $700^{\circ}C$. The grain size of ${\beta}-FeSi_2$ powders analyzed by Hall plot method was 44nm.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2001년도 하계학술대회 논문집
• /
• pp.100-103
• /
• 2001

In order to investigate the magnetic properties of CoCr-based bilayered thin films on kind of underlayer, we introduced amorphous Si layer to Co-Cr(-Ta) magnetic layer as underlayer. With the thickness of CoCr, CoCrTa single layer, crystalline orientation and perpendicular coercivity was improved. It was revealed that by introducing the Si underlayer, the c-axis orientation of CoCr, CoCrTa magnetic layer was improved largely. However, with increasing Si film thickness, perpendicular coercivity and saturation magnetization of Cocr/si, CoCrTa/Si bilayered thin films was decreased. Grain size of bilayered thin films became larger.