• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.31 no.5
• /
• pp.307-312
• /
• 2018

Liquid phases in ZnO varistors cause more complex phase development and microstructure, which makes the control of electrical properties and reliability more difficult. Therefore, we have investigated 2 mol% $CaCO_3$ doped $ZnO-Co_3O_4-Cr_2O_3-La_2O_3$ (ZCCLCa) bulk ceramics as one of the compositions without liquid phase sintering additive. The results were as follows: when $CaCO_3$ is added to ZCCLCa ($644{\Omega}cm$) acting as a simple ohmic resistor, CaO does not form a secondary phase with ZnO but is mostly distributed in the grain boundary and has excellent varistor characteristics (high nonlinear coefficient ${\alpha}=78$, low leakage current of $0.06{\mu}A/cm^2$, and high insulation resistance of $1{\times}10^{11}{\Omega}cm$). The main defects $Zn_i^{{\cdot}{\cdot}}$ (AS: 0.16 eV, IS & MS: 0.20 eV) and $V_o^{\bullet}$ (AS: 0.29 eV, IS & MS: 0.37 eV) were found, and the grain boundaries had 1.1 eV with electrically single grain boundary. The resistance of each defect and grain boundary decreases exponentially with increasing the measurement temperature. However, the capacitance (0.2 nF) of the grain boundary was ~1/10 lower than that of the two defects (~3.8 nF, ~2.2 nF) and showed a tendency to decrease as the measurement temperature increased. Therefore, ZCCLCa varistors have high sintering temperature of $1,200^{\circ}C$ due to lack of liquid phase additives, but excellent varistor characteristics are exhibited, which means ZCCLCa is a good candidate for realizing chip type or disc type commercial varistor products with excellent performance.

• Current Photovoltaic Research
• /
• v.2 no.1
• /
• pp.1-7
• /
• 2014

We developed a method of growing thin Si film at $600^{\circ}C$ by hot wire CVD using a very thin large-grained poly-Si seed layer for thin-film Si solar cells. The seed layer was prepared by crystallizing an amorphous Si film by vapor-induced crystallization using $AlCl_3$ vapor. The average grain size of the p-type epitaxial Si layer was about $20{\mu}m$ and crystallographic defects in the epitaxial layer were mainly low-angle grain boundaries and coincident-site lattice boundaries, which are special boundaries with less electrical activity. Moreover, with a decreasing in-situ boron doping time, the mis-orientation angle between grain boundaries and in-grain defects in epitaxial Si decreased. Due to fewer defects, the epitaxial Si film was high quality evidenced from Raman and TEM analysis. The highest mobility of $360cm^2/V{\cdot}s$ was achieved by decreasing the in-situ boron doping time. The performance of our preliminary thin-film solar cells with a single-side HIT structure and $CoSi_2$ back contact was poor. However, the result showed that the epitaxial Si film has considerable potential for improved performance with a reduced boron doping concentration.

• Journal of the Korean Ceramic Society
• /
• v.40 no.4
• /
• pp.354-359
• /
• 2003

The microwave dielectric characteristics of (1-x)(Al$\_$$\frac{1}{2}$/Ta$\_$$\frac{1}{2}$/)O$_2$-x(Mg$\_$1/3/Ta$\_$2/3/)O$_2$ (0$\leq$x$\leq$1.0) ceramics were investigated by crystalstructure, variations of ionic polarizability, and microstructures. As x increased, (1-x)(Al$\_$$\frac{1}{2}$/Ta$\_$$\frac{1}{2}$/)O$_2$-x(Mg$\_$1/3/Ta$\_$2/3/)O$_2$ transformed to tetragonal structure. Because the ionic radius of (Mg$\_$1/3/Ta$\_$2/3/)$\^$4+/was slightly bigger than one of (Al$\_$$\frac{1}{2}$/Ta$\_$$\frac{1}{2}$/)$\^$4+/, the cell parameters increased with increase of (Mg$\_$1/3/Ta$\_$2/3/)O$_2$concentration and coincided with prediction of the molecular additivity rule. As x increased, the compositions revealed ordered phase and were of single phase above 60 mol%. The increase of the ordered phase and grain size enhanced the Q and when ordering was completed at x over 0.6, the grain size was major factor for the increase in the a. Though the grain size increased, however, the porosity deteriorated the q. Therefore, the a depended on the order/disorder, the porosity, and the grain size in regular order.

• 한국초전도학회:학술대회논문집
• /
• v.9
• /
• pp.185-188
• /
• 1999

Biepitaxial Y$_1Ba_2Cu_3O_{7-x}$ (YBCO) and La$_{0.2}Sr_{0.8}MnO_3$ (LSMO) thin films have been prepared on SrTiO$_3$ buffer layer and MgO seed layer grown on Al$_2O_3$(11${\bar{2}}$0)substrates by dc-sputtering with hollow cylindrical targets, respectively. We charaterized Josephson properties and significantly large magnetoresistance in YBCO and LSMO films with 45$^{\circ}$ grain boundary junction, respectively. The observed working voltage (I$_cR_n$) at 77 K in grain boundary junction was below 10${\mu}$V, which is typical I$_cR_n$ value of single biepitaxial Josephson junction. The field magnetoresistance ratio (MR) of LSMO grain boundary juncoon at 77K was enhanced to 13%, which it was significant MR value with high magnetic field sensitivity at a low field of 250 Oe. These results indicate that inserting the insulating layer instead of the grain boundary layer with metallic phase can be possible to apply a new SIS Josephson junction and a novel magnetic device using spin-polarized tunneling junction.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.23 no.5
• /
• pp.368-373
• /
• 2010

In this study, we have investigated the effects of Cr dopant on the bulk trap levels and grain boundary characteristics of $Bi_2O_3$-based ZnO (ZB) varistor using admittance spectroscopy and dielectric functions (such as $Z^*,\;Y^*,\;M^*,\;{\varepsilon}^*$, and $tan{\delta}$). Admittance spectra show more than two bulk traps of $Zn_i$ and $V_o$ probably in different ionization states in ZnO-$Bi_2O_3-Cr_2O_3$ (ZBCr) system. Three kinds of temperature-dependant activation energies ($E_{bt}'s$) were calculated as 0.11~0.14 eV of attractive coulombic center, 0.16~0.17 eV of $Zn_{\ddot{i}}$, and 0.33 eV of $V_o^{\cdot}$ as dominant bulk defects. The grain boundaries of ZBCr could be electrochemically divided into two types as a sensitive to ambient oxygen i.e. electrically active one and an oxygen-insensitive i.e. electrically inactive one. The grain boundaries were electrically single type under 460 K (equivalent circuit as parallel $R_{gb1}C_{gb1}$) but separated as double one ($R_{gb1}C_{gb1}-R_{gb2}C_{gb2}$) over 480 K. It is revealed that the dielectric functions are very useful tool to separate the overlapped bulk defect levels and to characterize the electrical properties of grain boundaries.

• Journal of the Korean Ceramic Society
• /
• v.27 no.8
• /
• pp.991-1003
• /
• 1990

A precipitation method, one of the most effective liquid phase reaction methods, was adopted in order to prepare high-tech Al2O3/ZrO2 composite ceramics. Al2(SO4)3.18H2O, ZrOCl2.8H2O and YCl3.6H2O were used as starting materials and NH4OH as a precipitation agent, various types of metal hydroxides were obtained by single precipitation(series A) and co-precipitation(series B) method at the pH condition between 7 and 11. Fine Al2O3-ZrO2 powders were prepared at optimum calcination condition and the effects of ZrO2 on microstructures and mechanical properties of Al2O3 were investigated. The composition of Al2O3/ZrO2 composites wax fixed as Al2O3-15 v/o ZrO2(＋3m/o Y2O3). ZrO2 limited the grain growth of Al2O3 and increased grain size homogeneity of Al2O3 more effectively than MgO.Flexural strength values in Al2O3 and Al2O3/ZrO2 composites were 340-430 MPa and 540-820 MPa, respectively, and the effect of strength improvement showed 20-50% by adding ZrO2 to Al2O3. Fracture toughness of Al2O3/ZrO2 composites was improved by stress-induced phase transformation of tetragonal ZrO2 and toughening effect by microcrack was not observed. Also, ZrO2 particles located at Al2O3 grain junction contributed to toughening, while spherical ZrO2 particles located within Al2O3 grain did not contribute to toughening. Weibull moduli of Al2O3 ceramics and Al2O3/ZrO2 composites of series A and series B were 4.34, 5.17 and 9.06, respectively. Above 0.5 of failure probability, strength values in Al2O3 ceramics and Al2O3/ZrO3 composites of series A and series B were above 400 MPa, 700 MPa and 650 MPa, respectively.

• Korean Journal of Microbiology
• /
• v.19 no.1
• /
• pp.14-22
• /
• 1981

Protein content of cellulosic wastes, such as spent grain, hop bark, spent rye, rice straw, rice hull, saw dust and used newspaper, was increased by a mixed culture of C. utilis wastes having 66-75% moisture. Among the fungal strains tested. A.phoenicis KU175 was the most powerful to increase the protein content of A. phoenicis during the mixed culture with C. utilis in the CMC medium reached at the peak for one day culture after inoculation of the both strains at the same time, while it reached at peark from the beginning of the mixed culture, when A. phoenicis was inocultated for 12-24hours prior to the inoculation of C.utilis. To increase the protein content of the cellulosic wastes by the mixed culture of C.utilis and A.phoenicis, the inoculation of both strains at the same time was more effective than the preinoculation of A. phoenicis for 6-24 hours. Content of crude cellulose in the used newspaper, saw dust and spent grain was high relatively, and the lignin content of spent grain, spent rye, and rice strew was reduced more than half by the treatment of 2% NaOH. However, effect of alkali treatment of increase the protein content of the cellulosic wastes was not prominent in the case of mixed culture. Protein content of the cellulosic wastes was increased prominently by the mixed culture of C.utilis and A.phoenicis in semi-solid substrate, compared with the single culture of C. utilis, although the latter increased the protein content of cellulosic wastes considerably. The effect of mixed culture of C. utilis and A. phoenicis increased 4-fold the protein content of spent grain, and more than doubled crude protein in hop bark and rice straw.

• Journal of Crop Science and Biotechnology
• /
• v.10 no.2
• /
• pp.79-85
• /
• 2007

Rice bran application just after transplanting has been increasingly practiced as an herbicide-substitute for organic rice production in Korea. However, this practice is frequently reported to be unsatisfactory in weed suppression. An experiment with five treatments that combines flooding depth, rice bran application dose, and herbicide treatment was done in the paddy field to evaluate whether rice bran application under deep flooding can lead to a successful weed control in compensation for the single practice of rice bran application. Rice bran was broadcasted on the flood water surface just after deep flooding of 8 to 10cm that was started at seven days after transplanting. In the shallow flooding plot without herbicide six weed species were recorded: Monochoria vaginalis, Echinochloa crus-galli, Ludvigia prostrate, Cyperus amuricus, Aneima keisak, and Bidens tripartite. Among the first four dominant weed species, deep flooding significantly suppressed the occurrence of Echinochloa crus-galli and Cyperus amuricus while did not suppress the occurrence of Monochoria vaginalis and Ludwigia prostrate. On the contrary, rice bran application under deep flooding suppressed significantly Monochoria vaginalis and Ludwigia prostrate while didn't exert an additional suppression of Echinochloa crus-galli and Cyperus amuricus compared to deep flooding alone. Rice bran application and deep flooding suppressed complimentarily all the six weed species to a satisfactory extent except for Monochoria vaginalis of which suppression efficacy was 31.9%. Deep flooding reduced the panicle number substantially by inhibiting the tiller production, increased the spikelet number per panicle slightly, and leaded to a lower rice grain yield compared to shallow flooding with herbicide. Rice bran application under deep flooding mitigated the panicle reduction due to deep flooding, increased the spikelets per panicle significantly, and thus produced even higher grain yield in the rice bran application of 2000kg $ha^{-1}$ as compared to the shallow flooding treatment with herbicide. In conclusion, this practice applying rice bran under deep flooding would be promising to be incorporated as an integral practice for an organic rice farming system.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.7 no.1
• /
• pp.44-49
• /
• 2019

The purpose of this study is to analyze the fundamental characteristics of concrete with the change of reject ash(Reject ash=Rj) in the mixed aggregate where single grain aggregate of different grain size and aggregate of opposite grain size are mixed together, to analyze the possibility of a mixed aggregate system that premixes at an aggregate manufacturing plant and delivers it as one aggregate. As a result of the experimental study, it was found that the grain size regulation is satisfied if the mixed aggregate(CSb+SS) is substituted for about 5% of Rj. In the case of the fluidity slump, slump flow and air volume, it was found that they decrease as the substitution ratio of Rj increases, while the compressive strength increases as the substitution ratio of Rj increases. Therefore, it is analyzed that it would contribute greatly to an improvement of quality such as improvement of compressive strength if adequate fluidity and air quantity are secured by the water reducing agent and AE agent while premixing the Rj, which is disposed of by landfill, with about 5% of the mixed aggregate.

• Korean Journal of Materials Research
• /
• v.31 no.10
• /
• pp.576-581
• /
• 2021

To improve the shortcomings and expand the advantages of the single-roll melt drag method, which is a type of continuous strip casting method, the melt drag method with a molding belt is applied to AZ31 magnesium alloy. By attaching the forming belt to the melt drag method, the cooling condition of the thin plate is improved, making it possible to manufacture thin plates even at high roll speed of 100 m/min or more. In addition, it is very effective for continuous production of thin plates to suppress oxidation of the molten metal on the roll contact surface by selecting the protective gas. As a result of investigating the relationship between the contact time between the molten metal and the roll and the thickness of the sheet, it is possible to estimate the thickness of the sheet from the experimental conditions. The relationship between the thin plate thickness and the grain size is one in which the thinner the thin plate is, the faster the cooling rate of the thin plate is, resulting in finer grain size. The contact state between the molten metal and the roll greatly affects the grain size, and the minimum average grain size is 72 ㎛. The thin plate produced using this experimental equipment can be rolled, and the rolled sample has no large cracks. The tensile test results show a tensile strength of 303 MPa.