• 한국수산과학회지
• /
• 제20권4호
• /
• pp.370-378
• /
• 1987

Wave reflection control functions of mound for the foundation of composite and perforated break-waters were investigated through the theoretical considerations. The theory developed is based on a simple summation of components of reflected waves. The applicability of the theory is assured by the comparative studies of the theoretical calculation and experimental data on the sea surface elevation in front of a breakwater. It is found that the reflection is mainly controlled by depth and width of the mound. In the design of composite type perforated breakwaters, the width of perforated part of the upright section can be decreased to less than half of the conventional design width for the same reflection by using the reflection control function of mound part and the reflection can be reduced until less than $30\%$ of that in the composite breakwaters. Using the results, a design method of mounds is proposed, by which the reduction of wave reflection is assured under the given wave conditions.

• 오토저널
• /
• 제10권3호
• /
• pp.45-50
• /
• 1988

The measurement system of the pressure in engine cylinder is developed with the aids of the microcomputer, A/D converter and simple electrical circuits. The experiment is performed in 4 cycle single cylinder Gasoline engine. When data for the pressure progress is sampled, clock signal or signal from the crank angle is used as trigger. The variation of the pressure during the cycles can be well obtained experimentally. So, the informations which are necessary in the combustion analysis, i.e. expansion pressure, indicated mean effective pressure, the magnitude and time of the maximum pressure ignition time, the rate of pressure rise and heat release and combustion rates can be obtained by the calculation using experimental data. Also, the informations about the after-burning process, the existence of the detonation waves and end time of combustion can be investigated from this study.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2006년도 춘계학술대회논문집
• /
• pp.143-146
• /
• 2006

In this paper, a hybrid sensor is proposed that has two capabilities: The first is to sense longitudinal of flexural elastic waves selectively which are transmitted along the targe shaft, the second to measure the rotating speed of the shaft. All measurement are made in a noncontact manner since this sensor uses magnetostriction as its measuring principles. Furthermore, the switching between these two sensing capabilities are accomplished by a very simple mechanical operation. To verify the capabilities of the Proposed sensor, an Prototype sensor are fabricated and the experiments are made. The result shows this sensor can embody two sensing capabilities in one sensor configuration.

• 천문학회지
• /
• 제26권1호
• /
• pp.1-12
• /
• 1993

In order to explore the time dependence of the closure parameters of the two-fluid calculations for supernova remnants and the terminal shocks of stellar winds, we have considered a simple model in which the time evolution of the cosmic-ray distribution function was followed in the test-particle limit using the Bohm diffusion model. The particles are mostly accelerated to relativistic energy either in the free expansion phase of the SNRs or in the early phase of the stellar winds, so the evolution of the closure parameters during these early stages is substantial and should be followed correctly. We have also calculated the maximum momentum which is limited by either the age or the curvature of these spherical shocks. We found that SNRs expanding into the medium where the gas density decreases with the distance from the explosion center might be necessary to explain the observed power-law distribution of the galactic cosmic rays. The energy loss due to the escaping energetic particles has been estimated for the terminal shocks of the stellar winds.

• 대한전자공학회논문지
• /
• 제25권9호
• /
• pp.1027-1038
• /
• 1988

This paper, the last part of these three companion papers treated the electromagnetic diffraction by a dielectric wedge, presents the correction to the physical optics approcomation by the sheet currents of the Neumann expansion. Those expansion coefficients obtained by solving dual series equation amenable to simple numerical calculation may provide the asymprotically corrected solution. The validity of this result, satisfying both the edge condition near the tip of the dielectric wedge and the boundary condition along dielectric interfaces, is assured by approach of the corrected diffraction pattern to that of a perfectly conducting wedge for large permittivity of dielectric wedge.

• Kyungpook Mathematical Journal
• /
• 제53권4호
• /
• pp.661-680
• /
• 2013

The eigenvalue problems arise in the analysis of stability of traveling waves or rest state solutions are currently dealt with, using the Evans function method. In the literature, it had been shown that, use of this method is not straightforward even in very simple examples. Here an extended "variational" method to solve the eigenvalue problem for the higher order dierential equations is suggested. The extended method is matched to the well known variational iteration method. The criteria for validity of the eigenfunctions and eigenvalues obtained is presented. Attention is focused to find eigenvalue and eigenfunction solutions of the Kuramoto-Slivashinsky and (K[p,q]) equation.

• 한국통신학회논문지
• /
• 제25권7A호
• /
• pp.1057-1062
• /
• 2000

Allow me to introduce the development of an FM transmitter. The transmitter uses millmeter waves at the frequency of 60 GHz, and it can produce as much as 20 mW power with the band width of 1 GHz. The great feature of the FM transmitter is that it has been created by the special technique of utilizing the NRD (non radiative dielectric) waveguide. The advantage of adopting the NRD waveguide is that it can significantly reduce transmission loss. We can construct a small-size NRD guide transmitter in a simple way that has superb transmission performance. The NRD guide transmitter is very useful for CATV transmission or transmission over a wide range. In addition, the transmitter has almost the same band width as optical communication, and the data transmission speed of the transmitter is faster than that of optical communication. A transmitter with these merits would be highly appreciated as a way of ultra-highspeed communication network over short distances.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2007년도 추계학술대회 논문집
• /
• pp.299-299
• /
• 2007

This paper presents an omni-directional piezoelectric actuator which utilizes only one actuator. The actuator has a simple structure of cone type consists of two piezoelectric ceramics of ring type and electrodes divided four segments and a stainless steel body. To find the optimal operating condition of the actuator, the frequency characteristics of the actuator are analyzed by ATILA, FEM and measured by Impedance Analyzer. We have also developed a stage using the omni-directional actuator and an actuator driver circuit to create four sinusoidal waves with a variable frequency and phase difference.

• 비파괴검사학회지
• /
• 제22권6호
• /
• pp.649-658
• /
• 2002

As an attempt to further improve the reliability and effectiveness of ultrasonic testing (UT), a two-dimensional numerical simulator of UT was developed. The simulator models the wave medium (or test object) using the mass-spring lattice model (MSLM) that consists of mass-points and springs. Some previous simulation results, obtained by using MSLM, are briefly reviewed in this paper, for propagation, reflection, and scattering of ultrasonic waves. Next, the models of transmitting and receiving piezoelectric transducers are introduced with some numerical results, which is a main focus of this paper. The UT simulator, established by combining the transducer models with the MSLM, was used to simulate many UT setups. In this paper, two simple setups are considered as examples, and their simulated A-scan signals are discussed. The potential of the MSLM, transducer models, and the UT simulator developed in this study to be used in the actual UT is confirmed.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2000년도 추계학술대회논문집
• /
• pp.720-725
• /
• 2000

A new ultrasonic pulse-echo technique was developed and described for vibration measurement of the suspension assembly in hard disk drives. The method is based upon the difference in magnitude of two consecutive reflection waves from a moving object(suspension), while the traditional ultrasonic vibrometer uses the phase shift of the reference wave and the reflection wave. A cone-shape delay line is designed to access the small structure. A simple mathematical model is presented and analyzed with experimental results to show the feasibility of the method. The advantages of this ultrasonic vibration measurement method are relatively high resolution, low cost, and ease of implementation comparing with the Laser Doppler vibrometer.