• Archives of Plastic Surgery
• /
• v.36 no.3
• /
• pp.318-321
• /
• 2009

Purpose: The bony mallet finger injury is generally managed by conservative treatments, but operative treatments are needed especially when the fractures involve above 30% of articular surface or distal phalanx is accompanied by subluxation in the volar side. This is the reason they often result in chronic instability, articular subluxation and unsatisfactory cosmetic. In this report, We describe new method using the hook plate as an operative treatment of Mallet finger deformity. Methods: Among 13 patients with Mallet finger deformity who came from February 2006 to February 2008, six patient were included in surgical indication. Under local anesthesia, H or Y type incision was made at the DIP joint area. After the DIP joint extension, the hook plate was put on the fracture line, and one self tapping screw was used for fixation. 2 hole plate which was one of the holes in 1.5 mm diameter was cut in almost half and bended through approximately $100^{\circ}$. Results: In all six cases which applied the hook plate, complications such as loss of reduction or nail deformity were not seen. In only one patient, hook pate was removed due to inflammatory reaction after surgery. At 2 weeks after operation, active motion of DIP joint was performed. The result was satisfactory not only cosmetically but also functionally. At 6 weeks after operation, the range of motion of DIP joint was average $64^{\circ}$. Conclusion: The purpose of the operative treatment for mallet finger deformity using the hook plate is to provide anatomical reduction with rigid fixation and to prevent contracture at the DIP joint. While other operations take 6 weeks, the operation using the hook plate begins an active motion at 2 weeks after operation. Complication rate was low and the method is rather simple. Thus, the operation using the hook plate is recommended as a good alternative method of the mallet finger deformity treatment.

• Journal of rehabilitation welfare engineering & assistive technology
• /
• v.10 no.1
• /
• pp.65-72
• /
• 2016

In this study, a fully active transfemoral prothesis with a knee joint is designed considering stair walking conditions. Since the torque at the knee joint required for stair walking condition is relative high compared with the one in normal walking condition, the proposed design has high torque generating mechanism. Moreover, the transfemoral prothesis is designed in compact size to reduce its weight, which is related to comfortable fit and fatigue of patients. Flat type BLDC motor is used for simple and compact structure and various components are used to generate required torque with target working angle and speed. The weight reduction of structure is carried out using optimization method after the initial design process is complete. The optimization is conducted under the load conditions of stair walking. The optimized design is validated via finite element analysis and experiments. As a result, the weight is reduced using topology and shape optimization but maintaining the safety of structure. Also the space efficiency is improved due to its compact size.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.31 no.2D
• /
• pp.237-245
• /
• 2011

Asphalt Plug Joint(APJ) is a new type of expansion joint that it's application are increased in USA as well as several European countries. APJ's' advantages are cheap construction and maintenance costs, and simple construction and securing of excellent flatness. However, APJ's usability is hindered because it showed a problem of premature failure. Research for solving this problem has been progressed, and FEM analysis among existing researches was peformed. However, the behavior of APJ was insufficiently analyzed and the reliability of the analysis was much low, since the material showing complicated behavior was oversimplified, Therefore, a material model was proposed and its effectiveness was confirmed by comparing it with actual behavior in order to improve the reliability of FEM analysis in this paper. ABAQUS program was used for FEM analysis, and an elasto-plastic model and a viscous-plastic model as the material model of APJ were suggested on the base of experiment results of APJ material performed by Bramel et al. The elasto-plastic model was defined by time-independent analysis since it didn't consider time and strain rate, and the viscous-plastic model was defined by time-dependent analysis since it considered. Influence of various elements affecting the behavior of APJ was investigated, and it was confirmed that the time-dependent analysis showed better result closed to actual behavior than the time-independent analysis.

• 제어로봇시스템학회:학술대회논문집
• /
• 1996.10a
• /
• pp.12-15
• /
• 1996

In this paper, a new shape control law is derived as a result of introducing the parametric curve representation. This control alw is based on the estimation of the curve parameters corresponding to the target joint positions and the target tip position. Estimating target curve parameters makes it possible to find, easily, a simple shape control law by the Lyapunov design method.

• International Journal of Control, Automation, and Systems
• /
• v.3 no.3
• /
• pp.453-460
• /
• 2005

In this paper, a prototype Cartesian Parallel Manipulator (CPM) is demonstrated, in which a moving platform is connected to a fixed frame by three PRRR limbs. Due to the orthogonal arrangement of the three prismatic joints, it behaves like a conventional X-Y-Z Cartesian robot. However, because all the linear actuators are mounted at the fixed frame, the manipulator may be suitable for applications requiring high speed and accuracy. Using a geometric method and the practical assumption that three revolute joint axes in each limb are parallel to one another, a simple forward kinematics for an actual model is derived, which is expressed in terms of a set of linear equations. Based on the error model, two calibration methods using full position and length measurements are developed. It is shown that for a full position measurement, the solution for the calibration can be obtained analytically. However, since a ball-bar is less expensive and sufficiently accurate for calibration, the kinematic calibration experiment on the prototype machine is performed by using a ball-bar. The effectiveness of the kinematic calibration method with a ball-bar is verified through the well­known circular test.

• Proceedings of the IEEK Conference
• /
• 2001.09a
• /
• pp.869-872
• /
• 2001

Blind identification and equalization of communication channel is important because it does not need training sequence, nor does it require a priori channel information. So, we can increase the bandwidth efficiency. The linear prediction error method is perhaps the most attractive in practice due to the insensitive to blind channel estimator and equalizer length mismatch as well as for its simple adaptive algorithms. In this paper, we propose method for fractionally spaced blind equalizer with arbitrary delay using one-step forward prediction error filter from second-order statistics of the received signals for SIMO channel. Our algorithm utilizes the forward prediction error as training sequences for data estimation and desired signal for channel estimation.

• ETRI Journal
• /
• v.30 no.3
• /
• pp.441-450
• /
• 2008

The scalable extension of H.264, known as scalable video coding (SVC) has been the main focus of the Joint Video Team's work and was finalized at the end of 2007. Synchronization between media is an important aspect in the design of a scalable video streaming system. This paper proposes an efficient media synchronization mechanism for SVC video transport over IP networks. To support synchronization between video and audio bitstreams transported over IP networks, a real-time transport protocol/RTP control protocol (RTP/RTCP) suite is usually employed. To provide an efficient mechanism for media synchronization between SVC video and audio, we suggest an efficient RTP packetization mode for inter-layer synchronization within SVC video and propose a computationally efficient RTCP packet processing method for inter-media synchronization. By adopting the computationally simple RTCP packet processing, we do not need to process every RTCP sender report packet for inter-media synchronization. We demonstrate the effectiveness of the proposed mechanism by comparing its performance with that of the conventional method.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.26 no.6
• /
• pp.417-426
• /
• 2006

A Digital X-ray imaging system using Compton backscattering has been developed to obtain a cross-sectional profile and mass loss of corroded lap-splices of aging aircraft from density variation. A slit-type camera was designed to focus on a small scattering volume inside the material, from which the backscattered photons are collected by a collimated scintillator detector for interpretation of material characteristics. The cross section of the lap-joint is scanned by moving the scattering volume through the thickness direction of the specimen. The mass loss of each layer has been estimated from a Compton backscatter A-scan to obtain the thickness of each layer including the aluminum sheet, the corrosion layer and the sealant. Quantitative information such as location and width of planar corrosion in the lap splices of fuselages is obtained by deconvolution using a nonlinear least-square error minimization method(BFGS method): A simple reconstruction model is also introduced to overcome distortion of the Compton backscatter data due to attenuation effects attributed to beam hardening and quantum noise.

• Journal of Korea Multimedia Society
• /
• v.12 no.6
• /
• pp.824-832
• /
• 2009

Multi-radio multi-channel Wireless Mesh Network requires an effective management policy to control the assignment of channels to each radio. We concentrated our investigation on modeling method and solution to find a dynamic channel assignment scheme that is adapted to change of network traffic. Multi-path routing scheme was chosen to overwhelm the unreliability of wireless link. For a particular traffic state, our optimization model found a specific traffic distribution over multi-path and a channel assignment scheme that maximizes the overall network throughput. We developed a simple heuristic method for channel assignment by gradually removing clique load to obtain higher throughput. We also presented numerical examples and discussion of our models in comparison with existing research.

• 제어로봇시스템학회:학술대회논문집
• /
• 1999.10a
• /
• pp.21-24
• /
• 1999

There-have been many control strategies for the enact joint position tracking of flexible manipulators, but direct cartesian space tracking control methods an not developed well. In this paper, we propose a PD control method based on the cartesian error in the end point trajectory tracking. the proposed controller is composed of PD control combined with nonlinear saturation term hut has a very simple form. the effect of this term is continuous suppression of vibration which is induced by the coupling of rigid motion. This control works both on the regulation and on the tracking cases. The performance and validity of this control method is shown by simulation examples.