• Particle and aerosol research
• /
• v.15 no.4
• /
• pp.139-148
• /
• 2019

This study was performed for the application of a high-speed centrifugal cyclone to shale gas mining process. This device uses the centrifugal force to control particles similar to typical cyclones, and the disk located inside the cyclone is forced to rotate using a motor. The pressure difference occurred during the rotating of disk. Hence, inflow rate was generated without a blower fan. In addition, flow rate increased with elevating rpm of motor. The installing the disk in multiple stages on the inner rotor increased the instantaneous disk outlet flow. Hence, the control efficiency of oil particle increased from 1.05% to 31.2%. By modifying the structure of the disk so that the air flow to the opposite direction of the cyclone, the control efficiency of oil particles increased to 81.5%. By increasing the capacity of the motor and the size of the disk, the flow rate was increased to 2.5 ㎥/min because the rpm of motor and pressure difference increased. As rpm of motor increased, the cut-off diameter (d_pc) became smaller. Unlike the Lapple's equation, d_pc was inversely proportional to the effective number of rotations (N_e). The control efficiency was maintained even if the concentration of oil particles increased, for this reason, the higher the oil concentration, the more particles were accumulated and controlled.

• Korean Journal of Materials Research
• /
• v.27 no.5
• /
• pp.281-288
• /
• 2017

In this study, Fe-Ni slag, converter slag and dephosphorization slag generated from the steel industry, and fly ash or bottom ash from a power plant, were mixed at an appropriate mixing ratio and melted in a melting furnace in a mass-production process for glass ceramics. Then, glass-ceramic products, having a basalt composition with $SiO_2$, $Al_2O_3$, CaO, MgO, and $Fe_2O_3$ components, were fabricated through casting and heat treatment process. Comparison was made of the samples before and after the modification of the process conditions. Glass-ceramic samples before and after the process modification were similar in chemical composition, but $Al_2O_3$ and $Na_2O$ contents were slightly higher in the samples before the modification. Before and after the process modification, it was confirmed that the sample had a melting temperature below $1250^{\circ}C$, and that pyroxene and diopside are the primary phases of the product. The crystallization temperature in the sample after modification was found to be higher than that in the sample before modification. The activation energy for crystallization was evaluated and found to be 467 kJ/mol for the sample before the process modification, and 337 kJ/mol for the sample after the process modification. The degree of crystallinity was evaluated and found to be 82 % before the process change and 87 % after the process change. Mechanical properties such as compressive strength and bending strength were evaluated and found to be excellent for the sample after process modification. In conclusion, the samples after the process modification were evaluated and found to have superior characteristics compared to those before the modification.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2008.05a
• /
• pp.35-41
• /
• 2008

Qualitative enhancement of dwelling life has changing the recognition for the environment friendly wood which is being highlighted for its usage as an interior materials. This trend may prove the excellent performance of wood whose inherent characteristics has its comfortable, mild feeling of material, sound resistance and stabilities and the market of interior woods including floor, moulding and wooden panel as finishing interior materials is growing sustainably. However, since this materials is vulnerable to humidity and flame, waterproofing and flame retarding stability, an essential condition for interior materials, together with maintenance, are the main topics to be resolved. From the above-mentioned results, as a result of waterdrop contact angle, wood absorption volume and water content percentage test and the performance test of the processed materials after flame retardant, though there was some submerging time changes among types of woods for ensuring waterproofing performance improvement but as time passes, similar tendency was noticed to be formulated. As the submerging time is increased, so does the absorption volume and accordingly optimal level of range is judged to be drawn in order to ensure excellent performance, taking optimal economy into consideration. Therefore, it is considered that above-mentioned woods could be utilized for waterproof and flame retardant processed interior materials using uniform microwave and in order to put this technology into practical application, a research by way of diversified performance proving is required to be carried out.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.22 no.4
• /
• pp.152-159
• /
• 2014

Urea solution as a reductant of SCR has been widely used to reduce NOx emissions from diesel engine. But it has lots of problems which are freezing at low temperature due to liquid state, deposition of solid formation in the exhaust, dosing device, and complex package such as mixers for uniform concentration of ammonia. In order to overcome these obstacle, ammonium carbonate which is one of solid ammonium materials to produce ammonia gas directly by sublimation process is considered. Simple reactor with visible widow was designed to predict equilibrium temperature and pressure of ammonium carbonate. To simulate real operation conditions under automobile environment, several cycles of heating and cooling condition were settled, two different re-solidification materials were extracted from the reactor and visible window. Analytical study is performed to characterize these unknown materials by XRD(X-Ray Diffraction), FT-IR(Fourier Transform Infrared Spectroscopy), and EA(Elemental Analyzer). From analytical results, re-solidification materials from heating and cooling cycles are very similar to original material of ammonium carbonate.

• International Journal of Highway Engineering
• /
• v.5 no.2 s.16
• /
• pp.25-35
• /
• 2003

During construction of circular lifeline pipe, the non-proper compaction along the pipe and the decrease of compaction efficiency are the main problems to induce the failure of underground pipe. The use of CLSM(controlled low strength materials) is one of the applications to overcome those problems. In this research, the numerical analysis by PENTAGON FEM program was carried out for 20 cases with the couple of combinations on bedding materials, backfill materials, and pipes. From the FEM analysis, the use of CLSM as backfill materials reduced the settlement of ground surface and the deformation of pipe employed. In case of the vertical deformation on the pipe, common soil backfill for flexible pipes showed 2 times for rigid pipes, but CLSM backfill case did less deformation than the soil backfill for rigid pipes. CLSM backfills for rigid pipes showed the similar results. Judging from the FEM analysis, the use of CLSM increases the structure capacity of the underground pipes.

• Journal of the Korean Society for Heat Treatment
• /
• v.16 no.5
• /
• pp.260-266
• /
• 2003

In order to study the interfacial reaction between Nb thin sheet and Fe-C-(Si) alloy with different Chemical compositions, they were cast-bonded. The growth of carbide layer formed at the interface after isothermal heat treatment at 1173K, 1223K, 1273K and 1323K for various times was investigated. The carbide formed at the interface was NbC and the thickness of NbC layer was increased linearly in proportional to the heat treating time. Therefore, It was found that the growth of NbC layer was controlled by the interfacial reaction. The growth rate constant of NbC layer was slightly increased with increase of carbon content when the silicon content is similar in the cast irons. However, as silicon content increases with no great difference in carbon content, the growth of NbC layer was greatly retarded. The calculated activation energy for the growth of NbC layer was varied in the range of 447.4~549.3 kJ/moI with the compositions of cast irons.

• Journal of the Korean association of regional geographers
• /
• v.23 no.1
• /
• pp.213-226
• /
• 2017

Geography textbooks and atlases are typical printed materials broadly used in the classroom and the public education as certified materials. The students' atlas, as supplementary materials, is useful in teaching and learning geography in the classroom. This study examines and evaluates the supplementary role of the students' atlas in the institutional and pedagogical perspectives. The textbook and the atlas were written by different writers and publishers based on the interpretation of the geography curriculum, the pedagogical beliefs and interests. The textbook is submitted to be certificated by Ministry of Education. Then the textbook and the atlas which is passed in the certification process can be distributed to schools to use in the classroom. Most maps and materials are supplied in the textbook and the atlas variously depended on the authors' interpretation of geography curriculum, which are designed complementally. But, that maps and materials of respective book of even different author are similar and duplicated. Sometimes maps and materials of textbook and atlas are independent, not mutual complement. It needed that geography textbook and student's atlas take a efficient role supplementarily in these certification system of textbook.

• Restorative Dentistry and Endodontics
• /
• v.22 no.1
• /
• pp.305-324
• /
• 1997

Numerous materials such as amalgam, IRM, SuperEBA, dessicated ZOE, and Ketac-Silver have been used as a root-end filling material or to repair furcation perforations. But so far no material has been found to satisfy all of the requirements of an ideal restorative material. Recently, mineral trioxide aggregate (MTA) has been suggested for use as a root end filling material and for the repair of furcation perforations. The purpose of this study was to compare the effect of MTA on the proliferation of MC3T3/E1 osteoblastic cell, formation of bone nodule, alkaline phosphatase activity, and finally the tissue reaction of bone with those of amalgam, IRM, SuperEBA, dessicated ZOE, and Ketac-Silver. The following conclusions were drawn within the limits of the experimental results : 1. MTA showed a excellent proliferation of osteoblastic cell and Ketac-Silver showed moderate proliferation of osteoblastic cell. The rest of test materials showed no proliferation of osteoblastic cell. 2. Many of definite bone nodules were found in the MTA group. In contrast, Ketac-Silver group showed no definite bone formation but only showed mild sign of bone formation. 3. Alkaline phosphatase activity of Ketac-Silver and MTA showed similar results. But both of them showed higher activity than that of other materials (p<0.005). 4. The tissue reaction to implanted MTA in the calbarium of mouse was milder than that observed with other materials. The tissue reaction of dessicated ZOE showed the worst results among the test materials.

• Journal of Fashion Business
• /
• v.20 no.2
• /
• pp.124-133
• /
• 2016

Currently the fashion industry is developing to create a novel culture due to the very sensitive and knowledge-oriented advancement of the IT industry. With fast turnover of information, consumers have come to have a more diverse desire for purchasing. Cubical expression techniques, which empathizes formativeness, can be a creative expression method adjusting into the trend of this era. Along with functional aspects of consumers, even in a textile manufacturing sector, new materials are required to meet sensitive and emotional aspects. Consumers' desire for new and creative designs and the development and adoption of new materials are essential to meet their emotions. The IT industry and fashion industry are forced to combine and a 3D apparel CAD system has been developed, enabling virtual clothing to be represented within a computer virtual space. All processes such as design, pattern creation, sewing and simulation are possible in 3D level. Digital clothing can shorten the production process time and is very effective in that it can reduce clothing waste generated during the sample production. This paper reviewed the works of Dutch designer, Iris van Herpen, who has developed formative designs. She tries to build, construct, and sculpt employing diversified materials other than soft textile materials, as shown in her series of fashion shows. The materials include films, 3D printed polymers, stiff and sheer organza, and artificial leather textiles. A few characteristics of her works have been selected in order to prepare patterns exhibiting the traits. The paper further focused on the physical features of the textile materials used to express similar techniques and its various forms were reviewed.

• The Journal of Advanced Prosthodontics
• /
• v.8 no.6
• /
• pp.457-464
• /
• 2016

PURPOSE. The aim of this study was to determine whether two methods of documentation, print and electronic forms, for the assessment of patient-reported outcomes (PRO) in complete denture wearers provide comparable results. The study also quantified the time needed for filling the forms by each method. MATERIALS AND METHODS. Thirty participants enrolled in a university clinic answered two forms (a questionnaire for denture satisfaction and OHIP-EDENT). They provided answers with two application methods in a random order, with a one-month interval between them: (1) electronic forms on a tablet computer; and (2) print forms. The methods were compared in terms of mean results, correlation/agreement, internal consistency, and spent time. RESULTS. Mean results for both methods were similar for each denture satisfaction item (100-mm VAS) and OHIP-EDENT summary score. Both questionnaires presented good internal consistency regardless of the application method (Cronbach's ${\alpha}=0.86$ or higher). Correlation and agreement between the methods regarding specific items was at least moderate for the majority of cases. Mean time for the electronic and print forms were 9.2 and 8.5 minutes, respectively (paired t test, P=.06, non-significant). CONCLUSION. The electronic method is comparable to print forms for the assessment of important PRO of prosthetic treatment for edentulism, considering the results and time needed. Findings suggest the viability of replacing print forms with a tablet for applying the tested inventories in clinical trials.