• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2005.04a
• /
• pp.59-63
• /
• 2005

Compression tests were performed for six types of hat stiffened composite panels with different bonding methods and stiffener section shapes. Six panels showed similar behaviors in buckling and post-buckling region before a skin-stiffener separation failure occurred. The skin-stiffener separation failures occurred in the panels with closed type stiffeners regardless of bonding methods, but not in the panels with open type stiffeners. The separation failures not only reduced the postbuckling strength but also changed buckling mode and postbuckling stiffness. All the separation failures were initiated at the stiffener flange edges closest to skin buckling crests. The co-cured or secondary bonded panels with open type stiffeners had the largest structural performance. Because the post-buckling strength and performance of the composite stiffened panels are reduced by the separation failure, it is important to find bonding methods, stiffener types and manufacturing parameters for preventing of the separation failure.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2005.04a
• /
• pp.240-244
• /
• 2005

In this study a simple model is developed that predicts impact damage in a composite laminate using an analytical model. The model uses a non-linear approximation method (Rayleigh-Ritz) and the large deflection plate theory to predict the number of failed plies and damage area in a quasi-isotropic composite circular plate (axisymmetric problem) due to a point impact load at its centre. It is assumed that the deformation due to a static transverse load is similar to that occurred in a low velocity impact. It is found that the model, despite its simplicity, is in good agreement with FEM predictions and experimental data for the deflection of the composite plate and gives a good estimate of the number of failed plies due to fibre breakage. The predicted damage zone could be used with a fracture mechanics model developed by the second investigator and co-workers to calculate the compression after impact strength of such laminates. This approach could save significant running time when compared to FEM solutions.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2005.04a
• /
• pp.111-115
• /
• 2005

Recently, natural fibers draw much interests in composite industry due to low cost, light weight, and environment-friendly characteristics compared with glass fibers. In this study, mechanical properties were evaluated for two extreme cases of jute fiber orientations, i.e. the unidirectional yarn composites and the felt fabric composites. Samples of jute fiber composites were fabricated by RTM process using epoxy resin, and tensile, compression, and shear tests were conducted. As can be expected, unidirectional fiber specimens in longitudinal direction showed the highest strength and modulus. Compared with glass/epoxy composites of the similar fabric architecture and fiber volume fraction, the tensile strength and modulus of jute felt/epoxy composites reached only 40% and 50% levels. However, the specific tensile strength and modulus increased to 80% and 90% of the glass/epoxy composites. The main reason for the poor mechanical properties of jute composites is associated with the weak interfacial bonding between fiber and matrix. The effect of surface treatment of jute fibers on the interfacial bonding will be examined in the future work.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.48 no.4
• /
• pp.339-344
• /
• 2003

To identify the new source of breeding materials for rice salt tolerance, the salinity tolerance of thirty-four varieties was evaluated under 0.5% saline condition at seedling stage. The salinity score showed highly significant correlations to dry weight and dead leaf ratio. The tested varieties were classified into three groups by visual score, reduction ratio of dry weight, and dead leaf ratio. Eighteen varieties were classified as the highly tolerant group (salinity scores of 1.3-3.7), seven varieties were fallen into the tolerant group (salinity scores of 4.2-5.8), and others were susceptible (salinity scores of 6.7-9.0). In highly tolerant group, most indica varieties including Getu, Dikwee and Kuatic Putic, didn't exsert a panicle under the Korean climate. But six varieties, Xiangcho V, Annapuruna, HP 3319-2wx-6-3-1, Giza 175, and GZ 2447-S-17, GZ 4255-6-3 were suitable to the Korean climate, and their heading date (6-16, August) and culm length (65-78㎝) were similar to the Korean varieties. Accordingly, these varieties can be utilized as crossing materials for the salt tolerance in japonica rice.

• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 2000.11c
• /
• pp.560-568
• /
• 2000

The aims of this research were to investigate the preprocessing effect of spectrum data on prediction performance and to develop a robust model to predict SSC in intact apple. Spectrum data of 320 Fuji apples were measured with the on-line transmittance measurement system at the wavelength range of 550∼1100nm. Preprocess methods adopted for the tests were Savitzky Golay, MSC, SNV, first derivative and OSC. Several combinations of those methods were applied to the raw spectrum data set to investigate the relative effect of each method on the performance of the calibration model. PLS method was used to regress the preprocessed data set and the SSCs of samples, and the cross-validation was to select the optimal number of PLS factors. Smoothing and scattering corection were essential in increasing the prediction performance of PLS regression model and the OSC contributed to reduction of the number of PLS factors. The first derivative resulted in unfavorable effect on the prediction performance. MSC and SNV showed similar effect. A robust calibration model could be developed by the preprocessing combination of Savitzky Golay smoothing, MSC and OSC, which resulted in SEP= 0.507, bias=0.032 and R$^2$=0.8823.

• Mass Spectrometry Letters
• /
• v.7 no.2
• /
• pp.31-40
• /
• 2016

The analysis of nuclear materials and environmental samples is an important issue in nuclear safeguards and nuclear forensics. An analysis technique for safeguard samples has been developed for the detection of undeclared nuclear activities and verification of declared nuclear activities, while nuclear forensics has been developed to trace the origins and intended use of illicitly trafficked nuclear or radioactive materials. In these two analytical techniques, mass spectrometry has played an important role in determining the isotope ratio of various nuclides, contents of trace elements, and production dates. These two techniques typically use similar analytical instruments, but the analytical procedure and the interpretation of analytical results differ depending on the analytical purpose. The isotopic ratio of the samples is considered the most important result in an environmental sample analysis, while age dating and impurity analysis may also be important for nuclear forensics. In this review, important aspects of these techniques are compared and the role of mass spectrometry, along with recent progress in related technologies, are discussed.

• Journal of the Korean Society for Precision Engineering
• /
• v.33 no.4
• /
• pp.257-264
• /
• 2016

Solid state joining techniques are increasingly applied in a wide range of industrial applications. Friction welding is a solid state welding technique that is used to join similar or dissimilar materials. In this study, friction welding was applied to rotor shaft composed of a disk and a shaft. The disk and shaft were manufactured by hot forging and rolling, respectively. The aim of the study was to predict the structural characteristics during hot forging and friction welding process for rotor shaft of turbo charger. The structural characteristics were determined by heat input and heat affected zone (HAZ) during a short cycle time. Thus, transient FE analysis for hot forging and friction welding was based on heat transfer. The results were used to predict structural characteristics during hot forging and friction welding processes. The prototype of rotor shaft was manufactured by the result-based process parameters.

• Korean Journal of Soil Science and Fertilizer
• /
• v.47 no.5
• /
• pp.356-361
• /
• 2014

The coal fly ash (CFA) may be utilized as an extender for organic waste composting at the same time fully expected to solve all industrial waste disposal and sawdust tribe. The main objective in this study was to evaluate the effect of CFA addition as a bulking agent for swine manure composting. To determine the suitable addition rate of CFA as a bulking agent, 0, 10, 20 and 30% of saw dust were mixed with 30, 20, 10 and 0% of coal fly ash, respectively. Compost quality for swine manure composting was to evaluate temperature, pH, C/N ratio, and phytotoxicity as germination index. Stability of compost increased with increasing levels of CFA as bulking agent during swine manure composting due to the high alkaline materials including CFA. C to N ratio in treatment added CFA was higher than that of the control without CFA. After finishing composting, germination index of lettuce and cabbage in swine manure compost added 10% of CFA was similar to the control, all the heavy metal contents were far below the stipulated standard for organic farming. These results indicated tahr coal fly ash as bulking agents might be alternative materials to save saw dust and apply industrial products for swine manure composting.

• Transactions of Materials Processing
• /
• v.20 no.2
• /
• pp.99-103
• /
• 2011

Many parameters influence the frictional behavior of steel sheet during stamping. The contact pressure between a die and a sheet during stamping is one of them. Thus, this parameter is investigated for high strength steel (HSS) sheets, which are widely used for auto body panels due to their potential for weight reduction. Since HSS extend the limits of contact pressure for mild steel, the effect of this parameter on friction cannot be ignored. To investigate the influence of contact pressure on the frictional behavior of steel sheets, a flat type of friction test was conducted on three different steel sheets under various contact pressures. For bare steel sheets, the curve representing the relationship between contact pressure and friction coefficient exhibits a U shape. Coated steel sheets show a similar tendency except at low contact pressure. For these materials, when the contact pressure is very low, the friction coefficient slightly increases with pressure before it starts to decrease. The test results show that the effect of contact pressure on frictional behavior of steel sheet is not negligible even for contact pressures that are lower than the strength of HSS sheet.

• Korean Journal of Materials Research
• /
• v.9 no.1
• /
• pp.57-64
• /
• 1999

The electrical conductivity of TiO$_2$ doped with 0.05~1.5mol% WO$_3$ was measured in the oxygen partial pressure range of 10\ulcorner~10\ulcorner atm and temperature range of 1100~130$0^{\circ}C$ to investigate the defect types and the electrical properties. The grain size and density were increased as the liquid phase was formed by the doped WO$_3$. The secondary phase and WO$_3$peaks at the sample doped up to 4.0 mol% were not detected from the XRD results. The data(log$\sigma$/logPo$_2$) over 110$0^{\circ}C$ were divided into the four regions. From these experimental results, we proposed the following defect regions. 1) Magneli phase(extended defect), 2) Reduced rutile region which is similar to the behavior of undoped rutile, 3) Nearly stoichiometric Ti\ulcornerW\ulcornerO$_2$region in which extra charge of W\ulcorner cation is expected to be compensated by an electron, 4) Overstoichiometric Ti\ulcornerW\ulcornerO\ulcorner region which is a metal deficiency not to be observed in pure TiO$_2$. The electrical conductivity of w-doped TiO$_2$ was influenced by the measuring temperature, oxygen partial pressure, and the dopig content.