• 한국생물공학회:학술대회논문집
• /
• 2005.10a
• /
• pp.502-506
• /
• 2005

Three EGCG analogues were synthesized by the acceptor reaction of a glucansucrase from Leuconostoc mesenteroides B-1299CB with EGCG and sucrose. The transfer products was purified using Sephadex LG-20 column chromatography and high performance liquid chromatography (HPLC). EGCG-G1 and EGCG-G2 were novel compounds for the first time reported in this paper. EGCG glycosides showed similar or slower antioxidative effects according to their structures $(EGCG{\geq}EGCG-G1>EGCG-G1'>EGCG-G2)$. However, the water solubilities of the EGCG-G1, EGCG-G1' and EGCG-G2 were 52, 76 and 140 times higher than that of EGCG. Furthermore, they showed more browning resistance against UV irradiation than EGCG.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.54 no.4
• /
• pp.139-143
• /
• 2005

For application of carbon nano-tube (CNT) as a counter electrode materials of dye-sensitized solar cell (DSSC), the electrochemical behavior of CNT electrode was studied, employing cyclic-voltammetry (C-V) and impedance spectroscopy. Fabrication of CNT-paste and formation of CNT-counter electrode for characteristic measurement have been carried out using ball-milling and doctor blade process, respectively. Unit cell for measurements was assembled using Pt electrode, CNT electrode, and iodine-embedded electrolyte. Field emission-scanning electron microscopy (FE-SEM) was used for structural investigation of CNT powder and electrode. Sheet resistance of electrode was measured with 4-point probe method. Electrochemical properties of electrode, C-V and impedance spectrum, were studied, employing potentiogalvanostat (EG&G 273A) and lock in amplifier (EG&G 5210). As a results, the sheet resistance of CNT electrode is almost similar to that of F-doped SnO2 (FTO) coated glass substrate as approximately 10 ohm/sq. From C-V and impedance spectroscopy measurements, it was found that CNT electrode has high reaction rate and low interface reaction resistance between CNT surface and electrolyte. These results provides that CNT electrode were superior to that of conventional Pt electrode. Particularly, the reaction rate in the CNT electrode is about thrice high than Pt electrode. Therefore. CNT electrode is to be good candidate material for counter electrode in DSSC.

• Transactions on Electrical and Electronic Materials
• /
• v.11 no.6
• /
• pp.275-278
• /
• 2010

We have examined the Ferroelectric properties of $PbZr_{0.4}Ti_{0.6}O_3$ (PZT) grains by monitoring the surface potential through the utilization of Kelvin force microscopy. Hysteretic and time dependent behaviors of small and large grains were compared with each other. The smaller grain yields had smaller values of surface potential. However, the normalized voltage versus surface potential behavior indicates that the smaller grains became saturated earlier with respect to the writing voltages than did the larger grains. On the other hand, the surface potential hysteresis loop obtained from the smaller grains showed a similar shape to what might be obtained from a Zr rich PZT film. In contrast the hysteresis loop of the larger grain looks like that obtained from a Ti-rich film. In addition, the time dependent behaviors of the smaller grains also revealed a better response than the response of larger grains. The overall ferroelectric properties of the smaller grains seem better than corresponding properties for larger grains. The Ti/Zr ratio of the PZT film which was examined in this study was 60/40.

• Journal of Ocean Engineering and Technology
• /
• v.7 no.2
• /
• pp.19-29
• /
• 1993

The static tensile tests of GFRP, ID300, CFRID300 and CFRPEEK were made on the plain and notched specimens at room temperature. The results were discussed based on linear notch mechanics which was proposed by H.Nistani. The fracture of notched GFRP, ID300, CFRID300 and CFRPEEK specimens is controlled by the elastic maximum stress, $({\sigma}_max)$, and the notch root racius,$\rho$, alone, independently of the other geometrical conditions. The relation between fracture nominal stress,$({\sigma}_max)$, and stress concentration factor, $K_t$ and a part where $({\sigma}_c)$ is nearly constant independent of $K_t$. A similar phenomenon can be seen in the fatigue tests of notched specimes under rotating bending or push-pull. The almost constant $({\sigma}_c)$ values correspond to the nearly constant apparent stress intensity factor, $K_{1pc}$ values, obtained by assuming ,$\rho$=0. This can be attributed to the existence of the stable crack. Linear notch mechanics is very useful for analyzing the static tensile fracture behavior of notched GFRP, ID300, CFRPEEK specimens.

• International Journal of Fluid Machinery and Systems
• /
• v.5 no.2
• /
• pp.91-99
• /
• 2012

The Fighter aircraft transmission system consists of a light weight, High Speed Flexible Coupling (HSFC) known as Power Take-Off shaft (PTO) for connecting Engine gearbox (EGB) with Accessory Gear Box (AGB). The HSFC transmits the power through series of specially contoured metallic annular thin flexible plates whose planes are normal to the torque axis. The HSFC operates at high speed ranging from 10,000 to 18,000 rpm. The HSFC is also catered for accommodating larger lateral and axial misalignment resulting from differential thermal expansion of the aircraft engine and mounting arrangement. The contoured titanium alloy flexible plates are designed with a thin cross sectional profile to accommodate axial and parallel misalignment by the elastic material flexure. This paper investigates the effect of misalignment on the transmission characteristics of the HSFC couplings. A mathematical model for the HSFC coupling with misalignment has been developed for analyzing the torque transmission and force interaction characteristics. An extensive testing has been conducted for validating characteristics of the designed coupling under various misalignment conditions. With this the suitability of the model adapted for the design iteration of HSFC development is validated. This method will reduce the design iteration cycles of HSFC and can be extended for the similar development of flexible couplings.

• Proceedings of the IEEK Conference
• /
• 2002.06b
• /
• pp.45-48
• /
• 2002

This paper discusses the surface roughness of negative chemically amplified resists, SAL601 exposed by I-beam direct writing. system. Surface roughness, as measured by atomic force microscopy, have been simulated and compared to experimental results. Molecular-scale simulator predicts the roughness dependence on material properties and process conditions. A chemical amplification is made to occur in the resists during PEB process. Monte-Carlo and exposure simulations are used as the same program as before. However, molecular-scale PEB simulation has been remodeled using a two-dimensional molecular lattice representation of the polymer matrix. Changes in surface roughness are shown to correlate with the dose of exposure and tile baking time of PEB process. The result of simulation has a similar tendency with that of experiment.

• The Journal of Korean Academy of Prosthodontics
• /
• v.42 no.4
• /
• pp.443-457
• /
• 2004

Purpose: The purpose of this study was to analyze and estimate whether each company may produce the color of artificial teeth as it stands, in the standard of vita classical shade guide using ShadeScan$^{TM}$ System. Material and methods: we chose the products of 6 companies -EFUCERA, IVOCLAR, ENDURA, TRUBYTE, DURADENT, and DURACROSS- estimated the shade value of each fixed point(cervical, body, and incisal area) of artificial tooth, and verified the equality among the samples from the same company. Results: First, the variation appeared significant at cervical and incisal area. It means that there were significant differences between cervical and incisal area although the most similar artificial teeth to the patients’natural teeth were provided. Second, the results in the body area showed that the variation between artificial and natural teeth was finite(p<0.05) in that area. Conclusion: it shows that the reproduction of colors of artificial teeth might be successful regarding the body is the most important part for a determination of the color of artificial teeth. However, more complements are necessary for the better reproduction of the color of artificial teeth between cervical and incisal area.

• Journal of Electrochemical Science and Technology
• /
• v.5 no.2
• /
• pp.58-64
• /
• 2014

The surface of an ordered mesoporous silica (OMS) was functionalized using 1H,1H,2H,2H-perfluorooctyltrimethoxysilane at $20^{\circ}C$ and $60^{\circ}C$. It was shown that only elevated temperature allows lyophobic properties on the walls of OMS, eventually preventing pore flooding with nonaqueous electrolytes. The functionalized OMSs (OMS-F) were characterized with various techniques: wettability test, $N_2$ sorption measurement, high-resolution transmission electron microscopy (HR-TEM). Cathodes of $10mg/cm^2$ loading were prepared with a commercial Pt/C catalyst and polyvinylidene fluoride (PVDF, 2.5 wt.%) binder using a typical doctor blade method on a commercial gas diffusion layer (GDL) in the presence or in the absence of OMS-F additives. Subsequent discharge-charge curves were taken in a 1M LiTFSI-TEGDME electrolyte at 60oC in pure oxygen atmosphere. It was found that the discharge capacity was significantly affected by OMS-F: 5 wt.% of additive extended discharge capacity by a factor 1.5. On the other hand, a similar OMS material but synthesized at $20^{\circ}C$ did not show lyophobic properties and deteriorated cathode capacity.

• Fashion & Textile Research Journal
• /
• v.12 no.2
• /
• pp.149-155
• /
• 2010

The advanced and complicated modern society recognizes image creation based on the identity of the global competitive age as the important means. The requirement for a new vision to the globally environmental problem has affected on design so that as environmentally-friendly products and technologies have been developed and original expression modes have been appeared which the medium of paper which is natural material, paper has been highlighted newly. Hanji made of mulberry fiber, a bast fiber of mulberry is a representative environment-friendly natural fiber. In addition, it has various functions similar to those of yellow earth such as emission of far infrared rays, antibiosis, deodorization, fast dry ability of sweat, and simple dyeing ability. It is Hanji threads that are produced from various processes of Hanji materials. Therefore, hanji threads are able to be both woven and knitted still remaining Hanji's excellent characteristics. In addition, it is light, bio-degradable, durable and washable, and it is an environment friendly product with the distinguished texture and sensitivity. Under the concept of 'Circle' designed the uniforms of music hall to inform that the uniforms as a media representing music hall represents the unique Sori Arts Center of Jeollabuk-do traditional style.

• Fashion & Textile Research Journal
• /
• v.10 no.1
• /
• pp.68-75
• /
• 2008

Demands and attempts to express Korean traditional beauty are increasing. Some schools choose the uniform in designs expressing the image of Hanbok, but recently there is a few increment of wearing the uniforms. For the improvement of the uniforms, first of all, the shape and the clothing materials of the uniforms should be considered. We have compared and analyzed the shape and the clothing materials of the uniforms reflecting the image of Hanbok, according to seasons and clothing items. The uniforms reflecting the image of Hanbok were worn in eight schools and all of them are Saenghwal Hanbok style. The shape of Saenghwal Hanbok school uniforms showed both Korean style and western style characteristics. Korean style characteristics were expressed through the appearance-related parts while western style characteristics showed through the performance-related parts such as open/closure method, armhole pattern and straight sleeve line. It was shown that girls' uniforms are more diverse and similar to the western style uniforms than boys' uniforms. It was found that most of the clothing material were synthetic fiber or mixture of natural/synthetic fiber, and polyester was shown to be used most.