• 한국정보전자통신기술학회논문지
• /
• 제12권4호
• /
• pp.366-372
• /
• 2019

본 논문에서는 불소가 함유된 상용 폴리이미드를 사용하여 빗살형 전극을 갖는 정전용량형 습도센서를 제작하고 특성 측정 및 분석을 수행하였다. 먼저 상용 폴리이미드의 성분 분석을 위해 실리콘 웨이퍼 상에 패턴닝을 하고 열처리 공정을 수행한 후 EDS 분석을 수행하였다. 분석 결과 탄소(C) 62.48 Wt%, 산소(O) 9.38 Wt% 그리고 불소(F) 성분이 평균 8.44 Wt% 포함되어있는 것을 알 수 있었다. IDT구조에 대한 설계값을 토대로 제작된 습도센서의 면적은 $1.56{\times}1.66mm^2$이며, 전극의 넓이와 전극간 폭은 동일하게 각각 $3{\mu}m$, 센서의 감도를 높이기 위해 전극 수를 166개, 길이를 1.294mm로 제작하였다. 제작된 센서에 대한 기본특성 측정 결과 감도는 24 fF/%RH, 선형 특성 < ${\pm}2.5%RH$ 그리고 히스테리시스는 < ${\pm}4%RH$로 나타났으며, 주파수 특성은 10kHz, 20kHz, 50kHz, 100kHz에서 습도변화에 따른 용량값 변화를 측정한 결과 주파수가 증가할수록 동일 습도에서 용량값은 작아지는 것을 확인할 수 있었으며 10kHz와 100kHz의 습도변화에 따른 용량값 편차는 평균 0.3pF으로 측정되었다.

• Transactions on Electrical and Electronic Materials
• /
• 제16권2호
• /
• pp.99-102
• /
• 2015

Thin film transistors (TFTs) with amorphous 2 wt% silicon-doped zinc tin oxide (a-2SZTO) channel layer were fabricated using an RF magnetron sputtering system, and the effect of post-annealing treatment time on the structural and electrical properties of a-2SZTO systems was investigated. It is well known that Si can effectively reduce the generation of oxygen vacancies. However, it is interesting to note that prolonged annealing could have a bad effect on the roughness of a-2SZTO systems, since the roughness of a-2SZTO thin films increases in proportion to the thermal annealing treatment time. Thermal annealing can control the electrical characteristics of amorphous oxide semiconductor (AOS) TFTs. It was observed herein that prolonged annealing treatment can cause bumpy roughness, which led to increase of the contact resistance between the electrode and channel. Thus, it was confirmed that deterioration of the electrical characteristics could occur due to prolonged annealing. The longer annealing time also decreased the field effect mobility. The a-2SZTO TFTs annealed at 500℃ for 2 hours displayed the mobility of 2.17 cm²/Vs. As the electrical characteristics of a-2SZTO annealed at a fixed temperature for long periods were deteriorated, careful optimization of the annealing conditions for a-2SZTO, in terms of time, should be carried out to achieve better performance.

• ETRI Journal
• /
• 제34권6호
• /
• pp.950-953
• /
• 2012

Schottky barrier single electron transistors (SB-SETs) and Schottky barrier single hole transistors (SB-SHTs) are fabricated on a 20-nm thin silicon-on-insulator substrate incorporating e-beam lithography and a conventional CMOS process technique. Erbium- and platinum-silicide are used as the source and drain material for the SB-SET and SB-SHT, respectively. The manufactured SB-SET and SB-SHT show typical transistor behavior at room temperature with a high drive current of $550{\mu}A/{\mu}m$ and $-376{\mu}A/{\mu}m$, respectively. At 7 K, these devices show SET and SHT characteristics. For the SB-SHT case, the oscillation period is 0.22 V, and the estimated quantum dot size is 16.8 nm. The transconductance is $0.05{\mu}S$ and $1.2{\mu}S$ for the SB-SET and SB-SHT, respectively. In the SB-SET and SB-SHT, a high transconductance can be easily achieved as the silicided electrode eliminates a parasitic resistance. Moreover, the SB-SET and SB-SHT can be operated as a conventional field-effect transistor (FET) and SET/SHT depending on the bias conditions, which is very promising for SET/FET hybrid applications. This work is the first report on the successful operations of SET/SHT in Schottky barrier devices.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2016년도 제50회 동계 정기학술대회 초록집
• /
• pp.296-296
• /
• 2016

ITO films doped with a small amount of high-permittivity materials not only retain the basic properties of ITO films but also improve some of their properties. We report the highly conductive and transparent (ITO:Zr) films with various substrate (RT to 300oC) temperatures on glass substrate for the HIT solar cell applications. We observed a decrease in sheet resistance from 36 to $11.8{\Omega}/{\Box}$ with the increasing substrate temperature from RT to 300oC, respectively. The ITO:Zr films showed also lowest resistivity of $1.38{\times}10-4{\Omega}.cm$ and high mobility of 42.37cm-3, respectively. The surface and grain boundaries are improved with the increase of substrate temperature as shown by SEM and AFM surface morphologies. The highly conductive and transparent ITO:Zr films were employed as front electrode in HIT solar cell and the best performance of device was found to be Voc = 710 mV, Jsc = 33.70 mA/cm2, FF = 0.742, ${\eta}=17.76%$ at the substrate temperature of $200^{\circ}C$.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2016년도 제50회 동계 정기학술대회 초록집
• /
• pp.340-340
• /
• 2016

We have prepared alumina (Al2O3) doped zinc oxide (AZO) films by DC magnetron sputtering (MS) technique and obtained higher self surface texturing at a high target angle (f). We have characterized the films and applied it as a front electrode of a single junction amorphous silicon solar cell. At a lower f the deposited films show higher values of optical gap (Eg), charge carriers mobility & concentration, crystallite grain size and wider wavelength range of transmission. At higher target angle the sheet resistance, surface roughness, haze factor etc for the films increase. For f=72.5o the haze factor for diffused transmission becomes 6.46% at 540 nm wavelength. At f=72.5o the material shows a reduction in crystallinity and evolution of a hemispherical-type sub-micron surface textures. A Monte Carlo method (MCM) of simulation of the AZO film deposition shows that such an enhanced self-surface texturing of the films at higher f is possible.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2015년도 제49회 하계 정기학술대회 초록집
• /
• pp.196.2-196.2
• /
• 2015

There are various issues fabricating the successful and efficient solar cell structures. One of the most important issues is band alignment technique. The solar cells make the carrier in their active region over the p-n junction. Then, electrons and holes diffuse by minority carrier diffusion length. After they reach the edge of solar cells, there exist large energy barrier unless the good electrode are chosen. Many various conductor with different work functions can be selected to solve this energy barrier problem to efficiently extract carriers. Tungsten oxide has large band gap known as approximately 3.4 eV, and usually this material shows n-type property with reported work function of 6.65 eV. They are extremely high work function and trap level by oxygen vacancy cause them to become the hole extraction layer for optical devices like solar cells. In this study, we deposited tungsten oxide thin films by sputtering technique with various sputtering conditions. Their electrical contact properties were characterized with transmission line model pattern. The structure of tungsten oxide thin films were measured by x-ray diffraction. With x-ray photoelectron spectroscopy, the content of oxygen was investigated, and their defect states were examined by spectroscopic ellipsometry, UV-Vis spectrophotometer, and photoluminescence measurements.

• 센서학회지
• /
• 제15권5호
• /
• pp.334-340
• /
• 2006

A compact biosignal monitoring device was developed. Electrodes for electrocardiogram (ECG) and a LED and silicon detector for photoplethysmogram (PPG) were used. A lead II type was arranged for ECG measurement and reflected light was measured at the finger tip for PPG. A single chip microprocessor (model ADuC812, Analog Device) controlled a measurement protocol and processed measured signals. PPG and ECG had a sampling rate of 300 Hz with 8-bit resolution. The maximum power consumption was 100 mW. The microprocessor computed pulse transit time (PTT) between the R-wave of ECG and the peak of PPG. To increase the resolution of PTT, analog peak detectors obtained the peaks of ECG and PPG whose interval was calculated using an internal clock cycle of 921.6 kHz. The device was designed to be operated by 3-volt battery. Biosignals can be measured for $2{\sim}3$ days continuously without the external interruptions and data is stored to an on-board memory. Our system was successfully tested with human subjects.

• Progress in Superconductivity
• /
• 제12권2호
• /
• pp.110-113
• /
• 2011

We have grown a Nb/Gd bilayer on a$SiO_2$/Si substrate by using a DC magnetron sputtering system, which was fabricated in situ with silicon stencil masks. In order to investigate proximity effect of the Nb/Gd bilayer, we used a planar tunnel junction with an AlOx tunnel barrier by oxidizing the Al ground electrode at the bottom. A $Co_{60}Fe_{40}$ backing of Al was deposited so as to reduce the superconductivity of the Al, ensuring a normal counterelectrode. With a 50-nm-thick Nb layer, we have measured dI/dV (dynamic conductance) by varying the thickness of Gd, which can reveal the density of states (DOS) of the Nb/Gd bilayer as a function of the Gd thickness resulting from the proximity effect of a superconductor/ferromagnet bilayer (S/F). The SF proximity effect in Nb/Gd will be discussed in comparison to our previous results of the CoFe/Nb, Ni/Nb and CuNi/Nb proximity effect; Gd is expected to show different effects since Gd has f-electrons, while CoFe, Ni, and CuNi have only d-electrons. Our studies will focus on the triplet correlation in a superconducting pair.

• 한국결정성장학회지
• /
• 제13권2호
• /
• pp.93-97
• /
• 2003

FALC(Field-Aided Lateral Crystallization) 공정에서 요구되는 a-Si의 결정화는 인가한 전계(electric field)의 세기와 방향에 의존한다. 본 연구에서는 유한요소법을 적용하여 실제 패턴을 간단하게 모델링한 형상에 각 물질의 전도도를 대입하고, 전안을 가해 그 결과로 발생하는 전계의 분포를 계산하였다. 전계는 (-)극 주위에서 전극의 양쪽 모서리 부근이 가운데 부분보다 더 높게 나타났고 그 방향은 전극과 50~$60^{\circ}$를 이루는 대각선 방향이었다. 또한 예상한대로 크기가 작은 패턴이 큰 패턴보다 더 큰 전계 값을 가지는 것으로 나타났다.

• Journal of information and communication convergence engineering
• /
• 제1권4호
• /
• pp.199-204
• /
• 2003

In this paper, we present the thermal annealing effects of the W/$SiO_2$ multi-layer reflectors in ZnO-based FBAR devices with cobalt (Co) electrodes in comparison with those with aluminum (Al) electrodes. Various thermal annealing conditions have been implemented on the W/$SiO_2$ multi-layer reflectors formed on p-type (100) silicon substrates. The resonance characteristics could be significantly improved due to the thermal annealing and were observed to depend strongly on the annealing conditions applied to the reflectors. Particularly, the FBAR devices with the W/$SiO_2$ multi- layer reflectors annealed at $400^{\circ}C$/30min have shown superior resonance characteristics in terms of return loss and quality-factor (Q-factor). In addition, the use of Co electrodes has resulted in further improvement of the resonance characteristics as compared with the Al electrodes. As a result, the combined use of both the thermal annealing and Co electrodes seems very useful to more effectively improve the resonance characteristics of the FBAR devices with the W/$SiO_2$ multi-layer reflectors.